Where is heater fan located on 1983 Chevy S 10 4 wheel drive pick up?
how many actuators is on a 1997 s-10 if anyone knows please let me know.The activator to engage or disengage the front axle is located under the battery tray. It is best to remove the battery and battery tray to gain access.
Top rear of engine, under the distributor on drivers side. Best reached for R&R with distributor removed.
PO446 code isÊa diagnostic code for Evaporative Emission Control System Vent Control Circuit.Ê The most common fix for this code is to replace the gas cap and make sure it is turned till you hear a click.
There is no coil wire only spark plug wires. The coil pack can be found on the lower passenger side of engine block. It is best seen and accessed from under the vehicle.
It is located on the rear of the left side of the engine towards the firewall next to the AC accumulator (the big aluminum can looking thing). This dip stick should have a red handle and is inside a black tube that comes from underneath the engine. Simply flip the handle up and pull the dip stick...
Where is my oil sensor on a 96 Chevy S-10 pick up truck when looking at the truck from battery is on the left-side of me?
Need to know what size engine you have.
If you have a manual transfer case, you put the car into neutral or park (use your parking brake if you have a manual transmission), get out, lock your hubs (if your locking hubs are manual), get back in the car, and pull the lever back to the desired position. If you have an electronic transfer ...
Not easily accessible. It is behind the dash assembly attached to the HVAC assembly.
The horn is located just behind the Chevy emblem on the front grill. Removing the top bolts from the grill will allow you to access the bracket that holds the horn in place. Be careful not to break the electrical connector when removing the horn.
The fuel pump relay on a 1995 Chevy Pickup is located along with other relay switches in the fuse box next to the battery. This is on the passenger side fender wall above the wheel housing.
Tighten rocker arm down to 35 lbs of torque and your all done. These lifters are hydraulic and self adjusting. If you still have valve clatter, you have worn valve train parts.
The differential is part of the transmission gear train. It does not have a separate motor.
Why after replacing fuel injector on my 97 Chevy s-10 pick up truck wont start it cranks but don't turn on?
Fuel Pump or Fuel Pump Relay Maybe? It could be the o2 sensor or a fuel injection problem. Something with fuel is most likely the answer.
There isn't a control board - the controls are all in the switch.
With the 2.2 L engine and ACDelco R42LTS spark plugs, the gap is .040".With the 4.3 L engine and ACDelco R44LTS6 spark plugs, the gap is .060".Platinums are gapped at 0.60, and iridiums are typically gapped at 0.40... you shouldn't try to change the preset gaps.
The part number for the TYC parking light for a 1993 Chevy S10 pickup is 12-1247-01. The list price is $30.35, but they can be found online for $21 to $25.
It's not fused separately. If your fuel gauge isn't working, you either have faulty wiring to the gauge, or a faulty fuel sending unit.
I have an 05 Chevrolet and the flasher is on the back side of the fuse panel that is accessed on the drivers side of the dash.If you remove the knee panel by removing 2 7mm screws and pull strait out on the panel it can be changed.Good luck, Molugnut.
What would cause both headlights to go out but the running lights work on a 1995 Chevy S-10 4X4 pick up?
My money would be on the switch itself... having owned a couple Gen 2 vehicles on that platform, I've had the exact same problem... running lights would work, all other lights would work, but headlights and low beams would not... it's about a $20 part, so it won't set you back much.A problem with...
You have 2 O2 sensors on that vehicle. They are both threaded into the exhaust system, one before the catalytic converter and one after the catalytic converter. Bank 1 sensor 1 is the O2 sensor before the catalytic converter.
Really depends on how well you maintain it. 200 - 300k isn't unheard of with these vehicles, but you have to be diligent about keeping them up.
Lower front of engine, behind crankshaft balancer, best accessed from underneath.
It is located on the throttle body, opposite side of where the throttle cable is attached.
Both years are 2nd generation S-10s therefore most parts on each vehicle are interchangeable. Even some parts from the 1st generation are interchangeable with the 2nd generation.
I have a 2001 s-10 ext cab with 60-40 front seats. The module was located under the 20% of the drivers seat where a center console would be. It was under the carpet. I had to cut the carpet to get to it. Hope this helps.
Straight six engine, 12 US qts.V-8 engine, 15.8 US qts.
You must either drop the fuel tank to access the pump OR you can remove the 6 bolts which secure the box and lift it to gain access to the fuel pump. If you have the means for this method it will save you a couple hours on the job. and possibly a migraine too.
Under the hood, drivers side, backside of radiator support, best reached from under the vehicle.
The ignition module is screwed to the base plate of the distributor. Remove the distributor cap and rotor. Remove the two screws that hold it to the base plate. Unplug the two wiring clips from each end and replace.
The main fuse block in the '96-'97 S-10 pickups is located on the side on the driver's side of the dashboard, and is clearly visible on the side there when the driver's door is open. There are also several relays that control vehicle exterior lighting and internal accesories located behind a smal...
The shift cable runs under the drivers side carpet. After many years of moisture and corrosion the cable seizes up and you can't move the shift into gear or it moves with great difficulty.
Toyota vehicles do not utilize a fuel pump inertia switch.I don't believe it has one. That's a Ford thing.
I had a bad transfer case, maybe you have also
Parking brake (cables) may be stuck on.Could do with a little more detail here, as in, are they acting like they're frozen up, or are you not getting any power to them? Do you need to have your transfer case engaged in order for the vehicle to move? If so, there's something broken in your rear dr...
The bleeder is above the hydraulic hose connection.
Not without fabrication.
One answerer's view:No, the truck has to say z71 off road or z71 4x4 for it to actually be four wheel drive now the z71's that just say z71 on the side of the truck are not four wheel drive they have skid plates and other off road features but they are not for wheel drive!!!Another answerer's vie...
The ABS light is on because there is a problem within the ABS system. The light will remain on until the problem is fixed. The light will go away once the problem is fixed.Fix the deficiency. The light will go out on its own after you get up to 15 MPH once you've corrected the problem.
Simply push the hydraulic line back into the quick release fitting. When it is pushed all the way in you will hear a "snap" then it is locked in.
Need to know which sensor, there are several.
How can I fix my signal light switch on my Chevy S-10 . It has a hard click up or down and doesnt blink it stays on?
The switch itself isn't serviceable... you replace it. If your indicators aren't blinking, that might indicate a faulty turn signal relay. Do your four ways work?Replace the multi-function switch (aka, signal light switch) with a new one. Trying to repair the broken one is not practical.
the aux fan relay is located on the fan shroud on e46 vehicles. It is a rectangular box with wires going to a harness and two wires going to the fan motor. It is not a replaceable part and comes as part of the fan unit. It commonly goes defective and can be a cause of overheating. This despite th...
A manual lever on the floor board. You put the vehicle in neutral, shift the lever to the desired position, and roll.
If the truck is a 4 wheel drive, you can't repack the front wheel bearings. It has a sealed hub/bearing assembly that is not serviceable.
What do the number 2 and 1 mean in the 1987 Chevy S-10 Gearshift.and the D with a circle is for driving on the freeway right?
The "2" means that the transmission will only shift up to 2nd gear and will just rev the motor higher the faster you go. The D with a circle means Overdrive. And yes this is what you use for any normal driving.
The correct firing order is 1-3-4-2
few websites i have searched have come back with a flywheel to crankshaft torque spec of 50 ft-lbs same goes for the flex plate in automatic models. pressure plate torque spec is 23 ft-lbs
On line at Fixya.com. You could also buy a repair manual at a local auto parts store. Hope this helps.
Both cars drive all four wheels so in one sense there is no difference except that AWD has become an accepted description for a car that drives all of the wheels, all of the time.4WD is normally used on large SUV Four-Wheel Drive (4x4) vehicles designed to use the extra traction of 4WD in off roa...
it will be the same as the rear diff
Under the hood, passenger side of firewall,
A 1995 Nissan 6 cylinder pickup should have a spark plug gap of .044 inches. These spark plugs come preset from the factory.
The spark plug gap on a 1986 Chevrolet S10 4 cylinder pick up truck should be set at .060 inches. The spark plug for this vehicle may be purchased at any auto parts store.
The towing capacity of a 1997 Chevy Tahoe 4 door 4 wheel drive truck with a 3.73 gear ratio is 7,000 pounds.
There are several circuit boards in that vehicle. Need to know which one you are looking for.
However, it is stamped on the housing where the thermostat is located, "thermostat located on water pump." It would be nice if it was located in an easily accessible place like the top of the engine, however it's on the bottom passenger side of the engine.
The steering wheel? Unless the horn its self has died. Or the previous owner (if there was one) Moved to to a button.
Jacking up your 2005 Chevrolet Trailblazer is can be dangerous if done incorrectly.The video above shows you where the jack and jack kit is located in your Trailblazer how to assemble the components of the jack kit and safety precautions to take when using your jack.
Assuming this van is still carbureted, the fuel filter is located inside the fuel line fitting just as it enters the carburetor. It takes a 5/8" wrench to remove the fuel line and a 1" wrench to remove the fitting from the carburetor. Take note of the positioning of the filter so not to install t...
Generally under the dash on or near the steering column. If one side blinks, turn it on ans follow the sound to the exact location. FRONT SEATING AREA, DRIVER SIDE, UNDER DASH, MOUNTED ON PASSENGER SIDE OF STEERING COLUMN
The evap cannister is located underneath the vehicle in front of the fuel tank.
Probably inner fender. It purges gas fumes at start up so you can always follow the line from the tank to find it.
By useing a Good standard measure Tape and have a helper you can easily adjust the Toe in by first loeing up the Collars that connect the tie rods to the drag link losen both bolts on each end of the collars.then taking a pipe wrench or vise grips and gently Rotate then Collar clockwise to expand...
There are different types of block heaters. You can place a magnetic heater on the engine block, transmission pan, or on the oil pan. A hot pad heater can also be placed on the oil pan or transmission pan. An external engine oil reservoir heater is plumed into the oil supply and pumps the oil thr...
Should be in a removable housing at the engine end of the upper radiator hose
where is the starter located on a 2001 chevy tahoe? helloCustomer the starter is located on the passenger side of the engine.Here is a picture of it's location.Go under the truck and go to the passenger side of the engine.
205/75-15 or 215/65-15 Either size is a perfect fit.
If you just installed the pads, and didn't open up the hydraulic system (e.g., cracking the bleeder or disconnecting the brake lines), there's no need to bleed it.. just pump the foot pedal a few times and it'll sort itself out. Otherwise, there's a couple ways to to about it... one way requires ...
In Carid.If there's a pull and pay yard near you, check that out. There's enough attrition that they'll likely have at least a few of the GMT400 platform pickups there.Right here: http://www.ebay.com/sch/items/?_nkw=1995+chevrolet+c1500+cheyenne+grille&_sacat=&_ex_kw=&_mPrRngCbx=1&...
You may have to remove the seat to get to the bottom, but you should be able to get a replacment part from the dealer or a wrecking yard and repair a broken handle. If nothing else, take the seat to an upholstry shop that specializes in automobile interiors. Or you can use JB Weld and glue them b...
your front wheel bearing should be a whole hub assembly instead of the old inner and outter bearing and race..so it comes off when you take the axle nut off..you may need a fourwheel drive socket to fit the nut [auto zone, advance, napa carrys them] the whole thing slides off studs and all..alot ...
Its a 28ft Jayco 5th wheel.Quote: Where is my Jayco vehicle identification number and what does it look like? The Jayco, Inc.vehicle identification number (VIN) is 17 digits long and for towable products is located on the lower side of the “road side” sidewall.
The 2001 Chevy S 10 Blazer power door lock relay switch is located inside of the drivers side door. You will need to remove the drivers side door panel in order to access the door lock relay switch.
In the Fuse box, its usually lacated near the battery
Mahindra Thar 4WD PS Engine & Transmission The SUV is driven by a 2.5 litre, four cylinder, in-line diesel engine which can churn out 63 PS at 3200 RPM along with 182.5 Nm between 1500 to 1800 RPM.A four-wheel drive system is also equipped in the variant that transmits drive to all four wheels.