When Changed brakes bearings rear end seals on 2004 GMC 2500 HD duramax and still grinding on right side?

Cars & Vehicles
GM and GMC

The carrier bearings or pinion bearings may be at fault.

Previous questionWhat are three parts of the car that can use electrical energy?
Next questionCould you be a little more helpful for this?

Related question

What would cause the back right tire to grind on 2004 GMC 2500 HD series already changed brakes and bearing?

If the parking brake assembly hasn't been checked, check it out.

Read more

How much oil does your differential take on gmc serria 2500 hd 2wd 2004?

Probably 4 pints give or take a 1/2 pint.

Read more

Need to change wheel bearings on 2004 awd GMC Safari?

First, lift up the front and take off the wheels with a tire iron. Next, unbolt the brake caliper using the 3/8-inch ratchet and socket, pull it off the spindle and hang the caliper by the upper control arm. Then, remove the dust cap using a hammer and flathead screwdriver and remove cotter pin i...

Read more

What is causing a grinding noise on Passenger side when you turn right?

Could be bad pulley in accessory belt system if you have power steering, something contacting the rotor on that side or a failing wheel bearing.

Read more

What is that Thumping noise in tail end of car VW Golf 97 when turning when turning right get noise in rear right and when turning left get it in rear left side had struts replaced no help?

If you lowered the car or had suspension/strut work done you can be rubbingThe body in the boot?

Read more

Your right rear side light is not flashing on the outside but in the car it flashes really fast when you turn on and the left rear light is working Why is the right rear side not working?

Did you check if the bulb is ok? Normally if a bulb is burned out the speed of the indicator inside the car increases significantly.

Read more

How do you change the rear brake pads and depress the piston on the caliper on a 2004 Honda accord 4-D EX with disc brakes The rear caliper and the emergency brake are one unit and what tools.?

screw it in turn the piston clockwise and screw it in , only for rear brakes

Read more

What could cause a wheel bearing on a 14 bolt rear end to starve for oil and seize only on one side?

Hi, With any solid axle if the oil level is at all low it starves the left side first because all highways taper to the right for drainage so its like the right side is lower than the left and gravity takes care of the rest, of course if your car has 200K on it look for it to happen any time, if ...

Read more

What would make a ford f 150 shake when braking pads and rotors are in good condition when the rear end is jacked up off the ground and truck is in park the rear tires still spin?

It sure sounds like you have a warped brake rotor. They may "look" good but may still have excessive run out. For safety reasons, have a trusted mechanic inspect the brakes, steering and suspension for problems. As for the rear wheels spinning while elevated with trans in park, notice they spin i...

Read more

Right rear and which front brake do you bleed on 98 windstar?

You're supposed to bleed all four brakes or you really arent doing anthing, you could also cause improper and uneven wear on the brake pads them selves

Read more

What size socket do you need to change the wheel bearings on 1998 GMC Jimmy front and back axles?

Need to know if 2 wheel or 4 wheel drive for the front. Either way, there is no nut on the back axles.

Read more

My 1995 Mazda millenia is making a grinding as I increase the speed the noise increases Sounds as is coming from the front right side. I had the brakes an rotors replaced and it still hasn't went?

Brake calipers will sometimes not pull back from the rotors as they should and will make noise as the brake shoes literally rub the rotors continuously. This can happen even after changing both brakes and rotors. The contact points where the brake shoes slide back and forth on the caliper should ...

Read more

I already changed the rear brake light bulb on my C280 Mercedes Benz 2006 but it still won't light up?

Did you check the fuse?

Read more

Which cars have Lucas alternators on the right-hand side of the engine when viewed from the fan end?

My 1974 MG Midget has such an alternator.

Read more

2001 GMC Yukon. After changing the right and left tail lights to LED my center brake light is slightly on when the brakes are not applied. What would be the solution to eliminate that?

Get proper inline resistors wired into the circuit.Put the original bulbs back in.

Read more

When do you change the transmission fluid and fiter on a 2000 gmc Yukon?

You should change the transmission fluid and filter on a 2000 GMC Yukon every 5,000 to 6,000 miles. It does not need changes more frequently than that.

Read more

How do you change the rear disc brakes on a 2005 Chrysler town and country?

I just did replaced the rear brake pads and rotors on my 2005 Chrysler Town and Country Touring. I was stumped until I found: http://www.2carpros.com/forum/2002-Chrysler-town-and-country-rear-rotor-replacement-vt57403.HTMLThe rear is unlike the front, rather than removing 2 large hex nuts, on the...

Read more

When rotating tiers can you put the left rear on the right front and the right rear on the left front?

And move the fronts straight back, that's how I do it, as long as they are not directional tires.

Read more

Your tail lights don't work on the left side you have changed the bulbs on the side that don't work and the lights still don't work?

Check the fuse. Check the wiring to the lights, and also check your fuses.Isn't that what I said? Unless somebody rewired your car, This is a common problem on Honda's, Toy's etc.

Read more

What causes knocking in the front end and it goes away when step on the brakes?

Front Wheel Drive, could be bad CV Joints, Could be Control arm Bushings...

Read more

1998 Mercury Villager Bleeding brakes Put on new rear shoes and right side wheel cylinder was blown out cannot get fluid pressure to rear wheels. What could the problem be?

Make sure that the master cylinder is full. Loosen the rear line at the cylinder and make sure that the fluid has pressure and comes out at the loose line. If fluid flows, then check the lines fro a kink and bleed them again as there might still be air in the system.

Read more

Why would rear parking and brake lights stay on when the car is shut off?

There are two or more faults at work here depending on the car.If your car has a relay that runs brake lights or Tail lights one or both could be bad.ORIf your car has these items controlled by a body control module it could be bad or with this system the computer grounds the bulbs to make them w...

Read more

How do you move the piston back when changing rear brake pads on a Honda prelude 2.2 vti-r 93?

If parking brake is operated through service brake--then piston is threaded into caliper body--special tool is needed (not expensive) available at Sears or auto parts

Read more

What tools are needed to change the front and rear brake pads on a 2003 Mitsubishi Eclipse GT?

You will need a hoist, a socket wrench set and a torque wrench. You will also need the brake pads, brake fluid and brake grease.?æ

Read more

You have change brake calipers rotors and brake pads but your car is still shakeing but when you get to 60mph it stops whats is the problem?

Tire out of balance, or bent wheel.

Read more

Side to side movement of front wheels on my 96 F350 means it has loose tie rod ends right-- Would this also cause there to be a wobbling feeling in the steering wheel when driving on un-even surfaces?

Loose or worn tie rod ends on the 96 F350 can cause this problem. There could be other front end components wearing as well, check the entire front end system for problems.

Read more

Abs indicator light came on your dodge van 3500 mechanic replaced rear brakes and oil seals light went out had good pedal 20 miles light back on brakes work but soft pedal?

Soft pedal indicates air in system. Bleed the system of all air.

Read more

You changed the master cylinder and brakes and calipers on a ford explorer 2wd 1999 abs brake system and it still has air so how do you bled of the brake system?

there should be a bleeder on each caliper it takes two people for this part ive been told that on newer cars it needs to be turned on remove the reservoir cap on the master cylinder have your partner push the brakes three times and on the third push you use an offset wrench to open the bleeder wh...

Read more

How do you figure out how to check brakes cylinders on 1994 GMC sierra pu and or find out how fix no brake pressure but still have brakes at bottom of peddle?

Make sure master cylinder is full Have assistant step on brake pedal Walk around vehicle and look to see if any wheel is wet (from leaking wheel cylinder) See if any brake line is leaking Make sure rear brakes are adjusted properly (if drum brakes) Check to make sure caliper slides are not frozen...

Read more

When you turn on your left turn signal and you have to apply the breaks at the same time your right rear brake light goes out but the center brake light works?

If this were my car, I would replace the brake light switch ( near the brake pedal ). This could be the problem and is about the cheapest thing to start with. Good luck.check the ground connection at the taillights a bad ground will cause this

Read more

What would cause a thunk noise in the rear right side of a 2007 MazdaSpeed 6 when applying thrust not when braking switching gears or clutching in or out?

The rear-differential is shot. On a year old car with 20,000 miles. Quality engineering go!

Read more

When passing a vehicles on a 2 lane road way when do you return to the right side and at how many feet?

I return to the right lane after I see all of the car I passed in my rear veiw mirror.

Read more

Can you have a japan car made with the gas and brake peddles on the left side of steering your right leg was amputaed?

It wouldn't make a difference, JDM(Japanese Domestic Market) cars have the pedals exactly the same. only difference is which hand you use to shift. if your leg was amputated you would just have to figure out how to use the leg you still have, I've never seen a car have a brake and gas pedal on th...

Read more

There are times when my 2004 4-Runner will not move when put into drive. Then there will be a pop or clunk in the rear end and the vehicle will start to move forward.?

sounds like transmission problems( not moving in drive) and u-joint problems(pop or clunk

Read more

If a car gets rear ended on a foggy and rainy highway and that car didn't have their tail lights on as required by law is the car that hit them still 100 percent liable?

yes the law states that a vehile be operated in a manner and distance from vehicle in front, to be stopped in any circumstance Driving without the proper safety equipment (lights) was probably a contributing factor.

Read more

My brakes are not fully working and a red warning light and parking brake light is on why is it still on when the emergency brake is fully released?

Because the e brake is hooked into your braking system and that system has a problem.

Read more

2004 Yamaha Blaster and it burning trans gear oil you were told to replace the crankshaft seal so that's what you did but its still doing it can anyone tell you whats going on THANKS?

there is a wall between your trans part and your bottom end where ur crank is. If it is not leaking out of the outer case, then i dont know because it wont be getting past the wall unless it has a hole in the wall... and u will know if that has happened.

Read more

What causes a car to make a gurgling noise on passenger side front end fwd car when accelerating and hitting bumps at the same time and rolling downhill at low speeds or when turning and accelerating?

You may be hearing the coolant passing thru the heater core with an air pocket trapped in there.

Read more

Who is at fault when there is a 3-car collision and Car 2 hits the Car 1 without applying the brakes and Car 3 rear-ends Car 2?

Sorry to inform you as you were probably in car 2 or car 3. Whenever a car is rear ended the car doing the hitting is usually at fault as it is considered that they were tail-gating and thus did not have enough time to stop. I know you didn't want to hear this. Good luck.

Read more

Why does my rear driver-side tire make a rattling noise when going over a bump or rough roads could it be worn out bearings and is that an easy fix?

Assuming something isn't broke it is more likely the strut that is worn out. Bearing would grind all the time. When the strut is worn out and you go over a bump the tire will leave the ground which lets it vibrate and make noise.

Read more

Can the used car dealership or the auto manufacturer be held liable if the driver's side air bag failed to deploy when you rear ended another vehicle and you suffered injury?

If you can prove that they knew or that it was worked on by inexpereienced or unqualified people or that it was deliberately not repaired properly, perhaps.

Read more

What is the problem when you pull up on the emergency brake of a 1998 Ford Escort and you can still drive the car?

Either the cable needs adjusting, or the rear brakes need to be replaced.

Read more

What is thr bar that runs across the underside of a 98 Camaro It passes just below the rear end differental and connects to brackets on both sides what is the purpose?

It is called a sway bar or a control bar. It improves the handling of the vehicle while cornering. You will find one in the front also.

Read more

Why would the right turn signal indicator inside the car stop working when you turn the right blinker on but the blinker outside still work and how do you fix it?

There is also a light bulb in the dashboard, although most newer cars use LED's.The only way to fix a dashboard lamp failure is to remove the dashboard itself, which can be a complicated procedure dependent upon how new the car actually is.Some dashboard assemblies are "modular" which basically m...

Read more

You spun out on an icy road the car ending up in the other lane at a stand still the car that was behind you in the original lane couldn't stop in time and ended up rear-ending you by sliding into you?

The insurance will see it as your fault because you lost control first, the other driver probably didn't have time to react.

Read more

Your mark 8 wont rise up but when you jack it up on the driver side and only driver side then the compresser comes on and the car still dont rise but when you drop the car the compresser shuts off and?

In the trunk of the vehicle is a switch that says on/off ANYTIME you raise your car even to change the tire make sure you turn it OFF. Sounds like you were unaware of this so you should shut it off now. In the future or if you still have the problem a good trick to do if your air bags are still i...

Read more

What would cause a knocking sound when making left or right turns in a rear wheel drive car that started doing this after the brakes and rotors were replaced?

more than likely to be loose wheel bearings in rotars Dont rule out loose wheel lug nuts

Read more

Why does my left turn signal flashes fast in front but not in the back and the rear brake lights do not come on that side too in my 2006 Chevy Cobalt?

Start with checking the left rear brake light bulb.

Read more

What is the cause of a whistle sound on left wheel It's intermittent and as soon as I hit the brake it disappear. It normally happens when I driving on speed of 31 mph. Is it perhaps wheel bearing?

It is a "chirper spring" that is warning you that you have very little brake pad left. ------------------------------------------------------------------------------------------------------- Thanks for the answer, but I have already replaced the brake pads and brake disc. Before, I replaced that ...

Read more

Why does the flasher on the drivers side of your 2002 Trailblazer flash at about three times the normal speed when the headlights are on and about a quarter of the normal speed with the brakes on.?

Either you have one of the bulbs burnt out or the wrong size bulb installed.

Read more

Clicking noise from front end when turning left or right on my 52 laguna 1.8 could this be outer drive shaft and how do you fix them if it is?

yes they can be fixed, but in this day and time it is easier to take the old one to autozone and exchange it for a rebuilt one.$ about 100.00 to 150.00 depending on vehicle.

Read more

What would cause a right front brake to over heat on a ford bronco2 the brakes and right calluiper was change last week after locking up why would it do it again It gets so hot it melted the hub linin?

I have run into this before and it was a bad master cylinder that kept pressure on the brakes .

Read more

When i turn on headlights the Taillights do not come on. I replaced the bulbs they were blown still no taillights brake and turn signal working fine. Honda accord 2000?

Do parking and dash lights work? If not, may be fuse most vehicles it is the same circuit

Read more

When making left hand turn out of side street onto highway and oncoming car making left hand turn out of parking lot on to highway who has the right of way?

Whoever was at the intersection first.

Read more

What does it mean in a Peugeot 306 when a yellow light has come on permanently on the lower right hand side it has a symbol of a car with 2 arcs on either side and a squiggle under the car?

It is something to do with your ABS your brake pads may need to be replaced or your brake discs. drive carefully and no handbrake turns!

Read more

How do you fix brake tail light dash light reverse light and brake light on 1989 Camry if out I changed to tail light and fuse and when I turn on the headlights the fuse for the dash and tail blow?

The reason a fuse blows is that the thin wire melts from too much current flowing through it. Now if it blows only when you turn your headlights on, you have a good starting point for diagnosis. Somewhere in your headlight wiring, It's likely a positive power wire is grounding out. In other words...

Read more