What thermostast should be used in 350 Chevy?

Cars & Vehicles

195 degree F is most common.

Previous questionWhere is the blenddoor actuator motor in 1993 lincolntowncar executive series?
Next questionHow many coils do i need for 2.4 liter engine?

Related question

What temperature should a 1978 Chevy 350 run?

195 degrees F, + or - 5 degrees F with a 195 degree thermostat.

Read more

Should you use a super charger or turbo charger on your 1998 Chevy 350?

You should first figure out if your transmission is up to it. If you're running a 4L60E auto or NV3500 manual (the two transmissions most commonly mated to a GM small block for that era), it won't be. Then you'll have to figure out what PPM injectors you'll need, and what air intake and exhaust y...

Read more

What weight of oil should be used in 2002 Chevy Trailblazer?

Look at your oil cap. The weight is on the cap.

Read more

What type of oil is used in a 1988 Chevy small block V8 350?

Your climate may make a difference but 5W-30 covers most.

Read more

What size battery should you use for a 350 engine?

They are all about the same except for terminals and case or group size. See what group originally recommended for your vehicle and get the right terminals. If you can afford the best, get one with large CCA rating-Cold cranking amps.

Read more

What type of motor oil should be used in a Chevy Metro LSI 2001 with a 1.3 liter engine?

5w30 i only use synthetic walmart supertech is great and cheaper than mobile

Read more

What type of turbo Supercharger you should get for a chevy 350 performance car?

of all the s/chargers i installed in my shop pro charger has the best systems. check superchargers4less.com

Read more

What systems should be used in car valuation?

The crash rate and possibility of being broken down should be used in car valuation. Many cars are being over advertised for their look and not their reliability.

Read more

What words should not be used in a resume?

Here are a few additional examples of phrases hiring managers expect without needing to see them on your resume: Hard worker.People-person.Self-motivated.Team player.

Read more

What kind of oil should be use in a BMW?

depends on the year!!! all the newer models EXCEPT for the M's need Synth 5w-30. it must be synthetic!!!

Read more

What should you be looking for in a used car?

Before buying any used car, you should definitely check Carfax to get information on its previous owners and to see if any serious accidents were reported. Otherwise, you'd want to check the mileage, tires, brakes, and any other wear items to make sure that they do not need to be repaired or repl...

Read more

What antifreeze should be used in diesel engines?

Most antifreeze will work in any engine. For diesel engines in general, use a good long life coolant that includes nitrates (red stuff). For regular (green) coolant, most diesel manufactures require you to add your own nitrates or DFCA to this mix to prevent pitting of the cylinder liners. Check ...

Read more

Should there be any side to side play in the crankshaft on a 87 trx 350?

If you mean "end play", yes.

Read more

What type of brake fluid should you use in a 2003 Chevy 6500?

It came standard with DOT-3 but you can use DOT-5 IF you first flush/drain the entire system. Do not mix them.

Read more

How many freeze plugs are in a Chevy 350?

How to Remove the Freeze Plugs on a Chevy 350.The small-block Chevy 350 engine has two freeze plugs on either side of the engine block and two in the rear of the block on both sides of the camshaft.They are offered in steel or brass.

Read more

Do you need a thermostast in your car in Florida?

YES SO YOUR ENGINE WON'T OVER HEAT.

Read more

Firing order on a 350 Chevy engine?

All V8 Chevrolet's firing order is 1,8,4,3,6,5,7,2. 1,3,5,7 is on the left bank and 2,4,6,8 is on the right bank. The distributor turns clockwise.

Read more

Is the Chevy 350 a good engine?

The best-known small block V8 in GM's stable, the Chevy 350 engine is considered one of the 20th century's best engines.Sought after for its durability, quiet operation and performance, the 350 has also earned a reputation for reliability and usability in a variety of applications, including boats.

Read more

Should synthetic oil be used in 1990 civic dx?

It is your choice. It can even be mixed with conventional oil.

Read more

What is the torque specs on a Chevy 350?

You should always check the year of your engine before torquing any bolts.The specifications given are for the typical 350 engine.The Chevrolet 350 cylinder-head torque specification is 65 ft.-lbs.The intake installed onto cast-iron heads requires 30 ft.-lbs.

Read more

Should used trucks be cheaper?

Used cars and trucks are usually a better deal than new trucks, which depreciate instantly. However, if they are too cheap, beware of serious problems that could cost you a fortune in repairs.

Read more

Why does my Chevy 350 backfire?

Backfiring is typically caused by an air/fuel mixture that is too lean, meaning the mixture has too much oxygen in it.First, check that the mixture screw(s) on the carburetor are adjusted properly.Most of the carburetors installed on the 350 use a single air/fuel mixture screw, while some carbure...

Read more

What is the timing mark for a 350 Chevy?

There are actually two of them that you line up with each other. The first is a small pad attached to the timing chain cover near the top on the drivers side. The second is a line on the harmonic balancer. When using a timing light, the line on the balancer will line up with one of the numbered l...

Read more

What size carburetor is needed for a chevy 350?

depends on the application, but anywhere from 600 cfm up to 850 cfm is common. Carburetor manufacturers provide a formula for this calculation.

Read more

What are the cylinder numbers of a 350 Chevy?

Passenger side 2-4-6-8Driver side 1-3-5-7

Read more

What year Chevy 350 has dipstick on passangers side?

This can get a little tricky! If you are referring to the first generation small block Chevy that is. Here's a GENERAL guideline for stock oil pans with dipsticks that enter the block, and not the pan: 67-79 Drivers side 80-81 Driver or Passenger side 82-96 Passenger side As this was a corporate ...

Read more

What is the best carburetor for a Chevy 350?

What is the best carburetor for chevy 350 engine? 1.Rochester Quadrajet Stage 2 Carburetor JET 35002.Edelbrock 1406 Performer 4 Barrel Carburetor.Best Edelbrock Carburetor for Chevy 350.Holley 2300 0-7448 2-Barrel Carburetor.Holley 2 Barrel Carb for Chevy 350.Rochester 2GC 2 Barrel Carburetor.

Read more

What is the firing order for a 350 Chevy engine?

The most important thing to remember is that the firing order must follow the same pattern as the engine.The Chevy 350 firing order is 1-8-4-3-6-5-7-2.

Read more

What is the reguler running tep of a 350 Chevy?

carbureted and early Fuel Injected engines are happy running anywhere between 160 degrees F and 215 degrees. In cold climates a 195 F thermostat is recommended to get heat from the heater and have engine oil warmed enough.In extreme hot climates the 160 F T-stat is common and recommended.Since ab...

Read more

What is the Correct timing for a 92 Chevy 350?

8-10 deg.before top dead center.

Read more

What distributor comes with a 1975 Chevy block 350?

An HEI from the factory but can run most any aftermarket and depending on where you are sourcing may or may not even be included.

Read more

What is number one cylinder on a Chevy 350?

“What is the firing order of a Chevrolet 350 smallblock engine?” 1–8–4–3–6–5–7–2.Number one cylinder is, as you stand in front of the car looking at the engine, on your right hand, the closest cylinder.The cylinder numbers alternate between banks.

Read more

What is the spark plug gap on a Chevy 350?

Spark plugs for the Chevy 350 engine are readily available from any auto parts store.Spark plugs come pre-gapped, but you should always verify the gap with a spark plug gap tool.The gap for a 350 small block should be 0.035 inches.

Read more

What is firing order for a Chevy 350?

The most important thing to remember is that the firing order must follow the same pattern as the engine.The Chevy 350 firing order is 1-8-4-3-6-5-7-2.

Read more

What's the difference between a Chevy 305 and 350?

The 305 has different heads with smaller combustion chambers and smaller intake valves so as to not overhang the smaller bore.You can put 305 heads on a 350 but not necessarily the other way.A Chevy 305 has a 3.74" Bore with a 3.48" Stroke.A Chevy 350 has a 4.00" Bore and a 3.48" Stroke.

Read more

What vehicle did the 350 Chevy engine with casting no 8970010 come in?

Look again, could it be 3970010? If so it came out of a 1969-79 car, truck or Vette

Read more

Which direction is distributor rotation Chevy 350?

Clockwise rotation. Firing order= 1 8 4 3 6 5 7 2

Read more

Where is oil sensor on 350 Chevy?

The Original small block Chev 262, 283, 302, 305, 307, 350 and 400 all had the oil pressure sender under the distributor at the rear of the engine between the two valve covers.

Read more

What grade engine oil should be used in turbo charge vehicles in a humid counntry?

For older vehicles, 10W30 or 10W40 should be used in a hot climate. A lighter viscosity oil, such as 5W30, should be used in newer vehicles.?æ

Read more

What year is your 350 Chevy engine 3970010?

Could be a,1968 327ci, 2 bolt mainor1969 to 1979 350ci, 2 or 4 bolt main, from a car, truck or Vette.Re-post question with the engine code stamped numbers on the machined pad in front of the passenger side cylinder head. This code will help us give you more specific info.

Read more

What is the torque specs for Chevy 350 heads?

You should always check the year of your engine before torquing any bolts.The specifications given are for the typical 350 engine.The Chevrolet 350 cylinder-head torque specification is 65 ft.-lbs.

Read more

In a 1992 Chevy Beretta alternator how many wires should be connected?

There should be one female plug-in and one separate hot wire that is hot anytime the battery is hooked up.

Read more

Is a Chevy 350 an interference engine?

Re: chevy 350 interference heads? Technically they are not an interference engine.Lose a chain at high RPMs and the valves could float and make contact but at low RPMs they will not touch.The ignition timing cannot be adjusted.

Read more

What was the first car with the Chevy 350?

The 350 sbc was introduced in the new for 1967 Chevrolet Camaro , it was rated at 295 hp .

Read more

What HP does a Chevy 350 block 10066038 make?

Not possible to answer that question, too many variables.

Read more

What are the best spark plugs for a Chevy 350?

The 4 Best Spark Plugs for Chevy 350 – Reviews 2019 ACCEL 0526-4 Copper Core Spark Plug, (Pack of 4)NGK 3403 NGK G-Power Platinum Spark Plug TR55GP – 6 PCS.Autolite APP605 Double Platinum Spark Plug.NGK (7397-4PK) TR5IX Iridium IX Spark Plug, (Box of 4)Picking Out the Best Spark Plugs for Che...

Read more

What would cause no compession in cylinders 3 and 5 for a 350 Chevy engine?

A blown head gasket between 3 and 5 cylinders.Bent push rods.Burned valves.Valve adjustment done incorrectly.Valve adjustment lock nuts backed off, (replace with new nuts).

Read more

When checking a kingpin what tool should be used?

In just checking them for play, you would just use a suitable prybar for the vehicle. On HD trucks, I raise the steer axle one side at a time, and I have a five foot long prybar I stick under the tire to check for play in the kingpins. Make sure to not have your feet underneath the bar, in the of...

Read more

When should alcohol interventions be used?

Alcohol interventions should be used when one loses control of his/her day to day life in terms of harming themselves or others. Also when one cannot function by his/herself. Examples of this may be DUI, being involved in car accidents, missing work due to drunkeness, advice of a Dr due to a medi...

Read more

What motor oil should be used for 1988 Camry?

I recommend a high-mileage synthetic. 10w-30

Read more

What metal should not be used to make a battery?

Metal isn't used at all, Automotive Batteries are made of plastic with lead plates, if it were just metal it wouldn't leas as the battery works off of electrolysis is the case was made of metal if would be corroded and eventually leak out all the acid. so to answer you question... NONE only lead ...

Read more

What hitches should be used with a torque wrench?

A torque wrench should not be used on any hitch type.

Read more

What gear should be used when driving uphill?

When you're driving uphill, change down to a lower gear to avoid the engine struggling to give enough power.Driving downhill, you can use a lower gear to increase the effect of engine braking and reduce the risk of overheating the brakes.

Read more

When should a relay be used?

Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal.

Read more

When should cruise control not be used?

When you are on a hill, going down a hill.Never use it in heavy traffic, when it is raining, when towing, or when there is ice or snow on the road.It should not be used when:Usually when the car is below 25-20 mph (miles per hour) but you should'nt use it when you are travelling on hilly terrain ...

Read more

What is a power divider in a truck when and how it should be used?

On a tandem truck, you have two configurations - single screw, where the driveshaft goes directly from the transmission output directly to the differential of a live axle... the other axle will be a dead axle, and does not propel the vehicle.The other configuration is known as twin screw, and thi...

Read more

What precautions should be taken in the storage and use of home oxygen tanks?

Oxygen tanks should be kept in a well-ventilated area. Oxygen tanks should not be kept in the trunk of a car. "No Smoking--Oxygen in Use" signs should be used to warn visitors not to smoke near the patient.

Read more

What kind of things should you be looking for in a used truck?

If you're looking to buy a used truck, make sure to take it to a place where it can be raised for inspection and look for the following kinds of things: leaks and damage or repairs to previous damage; condition of the brakes, drive shaft, U-joints and steering components; and structural rust, not...

Read more

What gradeweight of motor oil should be used in a high-mileage engine?

20 w 50- after you have change it and the filter. Did you chang the transmossion fluid and filt too?

Read more

What type of antifreeze should be used in a Dodge Journey 2010?

A 2010 Dodge Journey uses red, five year HOAT antifreeze.

Read more

What kind of motor oil should you use for your 2001 Chevy express2500 van?

It depends on your climate but in most cases a 5W-30 is what it calls for.

Read more

How much does a Chevy 350 engine block weigh?

A bare Chevy 350 engine block weighs about 200 to 250 pounds. When you add in the crankshaft, camshaft, headers, and the intake it is more like 500 to 550 pounds.

Read more

How do you get more vacuum with your 350 Chevy?

the easiest way... valve and timing adjustments doesnt mean itll work right though

Read more

Which way does the distributor turn on a Chevy 350?

A: Chevy distributors rotate clockwise, so you'd want to turn the distributor counterclockwise to advance the timing.

Read more

How many cubic inches is a Chevy 350?

The Chevy 350 engine is a 350 cubic inch (5.7-liter) small block V8 with a 4.00 and 3.48 inch bore and stroke.Depending on the year, make and model of a car, horsepower ranges from approximately 145 to more than 370.

Read more

How Set idle speed on Chevy TBI 350?

There is no adjustment on a TBI fuel system, The Idle is controlled by the computerYou need to check the Idle speed control solenoid. You can find that on the top left rear side of the TBI housing. It screews in, and is about 4 inches long with an electrical connecter pluged into it. Also check f...

Read more

Will 68 Pontiac 350 headers fit 383 Chevy stroker?

No. The Pontiac headers will not bolt up to the Chevy small block.

Read more

How much horsepower does a 1987 Chevy 350 have?

Chevy 350 Engine Specs The Chevy 350 engine is a 350 cubic inch (5.7-liter) small block V8 with a 4.00 and 3.48 inch bore and stroke.Depending on the year, make and model of a car, horsepower ranges from approximately 145 to more than 370.

Read more

How many head bolts does a Chevy 350 have?

Chevy 265 283 302 5.0L 305 5.7L 350 400 Cylinder Head Bolts & Washers Set (Bolts & Washers)

Read more

How much horsepower does a 1972 Chevy 350 have?

Chevy 350 Engine Specs Depending on the year, make and model of a car, horsepower ranges from approximately 145 to more than 370.Rated at up to 380 pound-feet of torque, this engine is great for towing; however, fuel economy is low and -- depending on the compression ratio -- it might require pr...

Read more

What safety features should be in cars?

Cars should have doors and seat belts for safety features. Other safety features include: airbags, safety locks and anti-lock brakes.

Read more

Will a 1992 Chevy 427 motor bolt to a 1978 Chevy 350 turbo trans?

No. blocks are not the same.

Read more

What gear should my bike be in?

The Gears.Most geared bikes have one, two, or three chainrings in the front (the rings attached to the pedal crank arm) and anywhere from seven to 12 gears—or cogs—in the back (or the cassette attached to the rear wheel).

Read more

What room should the thermostat be in?

Ideal Thermostat Placement The best place for your thermostat is on an interior wall, away from all the areas we previously discussed (direct sunlight, air vents, your kitchen, hallways, windows and doors).Ideally, it should be placed toward the center of your home.

Read more

Is a 350 engine 5.7L in a 97' the same as the 350 engine 5.7L in a 98' for a Chevy pickup?

YES, There the same. NO DIFFERENCE.

Read more

What size cam should you use on a 30 over bored 350 flat top pistons and a 9.5 to1 compression?

that depends on what type of heads you have, what type and ratio rocker arms you have and what length pushrods you have. some heads have sufficient clearance to compensate for higher lift cams by having larger combustion chambers. Stock rocker arms are a 1.5 ratio on most small block Chevy engine...

Read more

What should tire pressure be in winter?

Several vehicle manufacturer's owner's manuals recommend operating winter tires several psi (typically 3-5) higher than their recommended pressures for summer and all-season tires.The 3-5 psi higher recommended inflation pressures increase tire stability and help offset the reduction in responsiv...

Read more

What PSI should tires be in winter?

Find your recommended tire pressure.You can find it written in your owner's manual or on a sticker attached to your door edge, glove box, or fuel hatch.Recommended tire pressure usually falls between 30-35 PSI.

Read more

What does 350 mean in a 350 engine?

The size of the engine is 350 cubic inches of displacement. Engines used to be measured in cubic inches of displacement, now they are measured in liters. A 350 is now usually referred to as the 5.7 liter.

Read more

How much horsepower does a 97 Chevy 350 have?

The 6.2-liter engine produced 143 horsepower and 257 ft-lbs.of torque.The 7.4-liter engine offered 230 horsepower and 385 ft-lbs.of torque.

Read more

Where are the casting numbers on a Chevy 350?

The casting number is located on the driver's side, top rear of the engine block.The number on the front passenger side of the engine block will NOT tell you the displacement of the engine block.

Read more

How much horsepower can a Chevy 350 make?

Using stock components (block, crank, rods, pistons, bolts, etc.) a typical 350 Chevy can make upwards of 350 - 375 HP before you exceed the reliability of the components.

Read more

How can you reduce fuel presssure in a 1974 Chevy 350 engine?

Those fuel pumps only made about 4 psi, so there would never be a reason to reduce it. If you are having problems with fuel overflowing the carb, it is more likely a needle and seat problem or a bad float.The fuel pressure required on a 1974 Chevy 350 is 7 to 8 1/2 psi.

Read more

How has the Chevy 350 block changed in any way other than bore?

When they went to TBI, the firing order changed. Some construction feature of the block changed with the transition from carbureted engines to TBI, as well.The Chevy small block went from a 2 piece rear main seal to a 1 piece rear main seal in 1987.

Read more

Will a Chevy 350 small block fit in a 2000 Jeep Wrangler?

You can make it fit with plenty of money and fabrication but it is not a plug and play.

Read more

What lights should you use in rain?

Any time your visibility is less than 150 metres because of heavy rain, for example, you'll want to use your low beams headlights.If you were to use your high beams in thick fog, for example, the light would get reflected back to you.

Read more

What lights should you use in fog?

Heavy rain, snow, sleet or fog Any time your visibility is less than 150 metres because of heavy rain, for example, you'll want to use your low beams headlights.If you were to use your high beams in thick fog, for example, the light would get reflected back to you.

Read more

Can a 350 transmission fit in a 1991 Chevy caprice with a 5.0 engine?

A TH350 can be used in a 91 Caprice with a 5.0 or a 5.7 engine. A 91 Caprice came with a 700R4 transmission in almost all cases. That being said, you must use a TH350 with a 9" tail shaft. These were available in 2wd Chevy trucks up to 86. They were also available in 72 to 76 Impala and Caprice.Y...

Read more

How do you fix joe's Chevy 350 small block?

Need to know what is wrong with it before we can help Joe fix it.

Read more

How much horsepower does a 1989 Chevy 350 have?

Engine Performance It had a bore and stroke of 4-by-3.48 inches, and a compression ratio of 9.5 to 1.Equipped on a Corvette, the 350 is capable of producing 240 horsepower at 4,000 RPM, and 345 pound-feet of torque at 3,200 RPM.

Read more

What Chevy engine is used in Indy cars?

INDYCAR has utilized the 2.2-liter, turbocharged V-6 formula since 2012, with exclusive use of twin turbos since 2014.Engines will continue to turn at a maximum of 12,000 RPM.On-track testing will begin in the summer of 2020.

Read more

Will a 1956 Chevy 3 speed trans bolt on a Chevy 350 engine?

If the 56 came with the Chevy V-8, yes. If the 56 came with the Chevy straight six, no. Different bolt pattern on the bell housing between the straight six and the V-8 engines.will a 1956 gmc 3 speed trans bolt on a chevy 350 v-8 engine

Read more

What kind of power steering fluid used in a 2000 Chevy s-10?

Use Dexron III the same stuff you would use in your automatic transmission.

Read more

Should a used vehicle need to be repaired with in the first six months?

Any vehicle can need repair at any time, new or used. A used vehicle is always a gamble, and you never know for sure how well it has been maintained. That is why when you buy a used car "As Is" always be prepared to spend some money on repairs. Factor that in when making an offer on the car.

Read more

What Oil filter is used for 94 ford 350 7.3?

I was looking at one of Fords websites and it shows :For a 1994 Ford F-350 , 7.3L DIESEL :IDI ( non turbo and turbo ) It takes the ( Motorcraft FL-784 engine oil filter )DI turbo - It takes the ( FL-1995 )

Read more

What to used to stop lifter tick in 1998 GMC Sierra 1500 with a 350 tbi?

A tick in a lifter is likely caused by poor fuel. Using a higher octane fuel will often stop the knocking or ticking.

Read more

Which engine should be used for maximum power generating?

It really depends on many things..what is it used for- drag-road racing, to power a pump/generator, boat?Is there a size/weight limit- 4cyl.,v16?what fuel? diesel, pump gas, alcohol, race fuel?How long before rebuild- 10yrs, 3 races?But in general-turbo diesel like the cummins 5.9 or duramaxall o...

Read more

How many years old should a used car be?

So for used car shoppers, purchasing a car that's two to three years old and driving it for three years results in some of the lowest costs for recent model cars.

Read more

How should a torque wrench be left after use?

However, there is a level of considered good practice that should be adhered to when using a torque wrench even if you don't need to unwind it after use.For a start, torque wrenches have moving parts and can be affected by corrosion and dirt in the mechanism.They should always be kept clean and i...

Read more

How old should a car be if buying it used?

The 'age' of the car is not really that matters but it's working condition is what is more important. A relatively new car with bad track record is worse than a 5 year old car with good maintenance record.

Read more