What is the typical compression ratio and combustion chamber pressure in a compression ignition engine?

Cars & Vehicles

Typical compression ratios between 18:1 and 23:1 are common, although in an effort to minimize oxides of N2 compressions as low as 16:1 are being employed generally resulting in a loss of 1-2 mpg resulting from the lower thermodynamic efficiency of the diesel cycle. Higher compression ratio yield higher thermodymic efficiency relative to the ideal or Carnot thermodynamic cycle.

I'm not sure who answered this but you are way off. 18:1 on up is for engines that run on Diesel or a variation of a bio-fuel. Gasoline engines are typically 8:1 on up to about 11:1 on the newer engines with coil on plug coils which can have over 80.000 volts per cyl. Thus alowing the variable valve timing and great mpg even on a large engine.

The gentleman asked about a compression ignition engine, which is a diesel engine. The rebuttal about an 8:1 would be for a spark ignition engine. I believe that the 1st answer was correct (Otto & Diesel would be upset). As for the pressure of the diesel/compression combustion, You could look on online commercials for piezo electric transducers to see what ranges they use to measure engine pressures during combustion in engine testing (food for thought).

Previous questionHow much did a gallon of gas cost in 1938?
Next questionHow many points in NJ does it take to lose your driver's license?

Related question

Compression ratio of the internal combustion engine is defined as?

The compression ratio of an internal-combustion engine, or an IC engine as it is more commonly called, is the ratio of the volume the highest capacity of the combustion chamber to its lowest capacity.In the IC engine, the piston makes a stroke, resulting in the compression of the air in the combu...

Read more

How do you calculate the pressure on explosion in a combustion chamber of a car engine?

There is this gauge you can buy it screws right into the spark plug port and when you turn your motor over slightly not starting it but just bumping the starter when you get the internals of the motor at a certain point it will read the exact max pressure in your cylinder.

Read more

How much pressure is in a combustion chamber?

Mechanical issues.Rocket combustion chambers are normally operated at fairly high pressure, typically 10–200 bar (1–20 MPa, 150–3,000 psi).

Read more

Are the intake and exhaust valves open During the stage of internal combustion engine operation in which the piston rises and compresses the fuel in the combustion chamber?

No, both valves are closed so as to create a seal around the combustion chamber so the fuel/air mixture can be compressed.It goes like this:Stroke 1 - the piston is drawn down in the combustion chamber with the intake valve open, allowing air to enter the chamber. At the same time, fuel is inject...

Read more

What is meant by the compression ratio of a combustion engine?

The compression ratio of a combustion engine is the relationship of the largest and smallest capacities of the combustion chamber. A higher compression ratio is advantageous because the engine operates more efficiently, extracting more mechanical energy from the fuel. Most gasoline-powered engine...

Read more

What is the compression ratio of and engine?

Compression ratio is the difference in the volume of a engine cylinder between when the cylinder is at it's largest volume, compared against when the cylinder is at it's smallest volume. Gasoline engines use 8:1 to 12:1 compression ratio. Diesel fuel engines use 14:1 to 25:1.

Read more

Why is the compression ratio of a spark ignition engine limited to about 9.51?

So the engine can run on regular 87 octane gasoline.

Read more

What is engine compression ratio?

The compression ratio is the ratio of the volume of the cylinder and the combustion chamber when the piston is at the bottom, and the volume of the combustion chamber when the piston is at the top.Automotive engineers can improve fuel efficiency and fuel economy by designing engines with high com...

Read more

What is a good engine compression ratio?

Compression ratios are often between 14:1 and 23:1 for direct injection diesel engines, and between 18:1 and 23:1 for indirect injection diesel engines.Since diesel engines operate on the principle of compression ignition, a fuel which resists autoignition will cause late ignition, which can lead...

Read more

Peak temperature in combustion chamber petrol engine?

2500K around 4000*F or 2225*C

Read more

What is compression ratio of IC engine?

The compression ratio is the ratio of the volume of the cylinder and the combustion chamber when the piston is at the bottom, and the volume of the combustion chamber when the piston is at the top.Automotive engineers can improve fuel efficiency and fuel economy by designing engines with high com...

Read more

What is the compression ratio of a diesel engine?

The compression ratio of a Diesel ranges from 14:1 to as high as 25:1.I agree just depends on engine.

Read more

What is the average compression ratio of a diesel engine?

Diesel engines are designed to operate at higher compression ratios, usually between 15 to 20, while petrol engines have lower compression ratios usually between 8 to 10.Since the higher the compression ratio of an engine the higher the thermal efficiency, so diesel engines generally have a bette...

Read more

What is the average temperature inside the combustion chamber of an internal combustion diesel engine?

the air temp at the end of the compression stroke for the ignition of diesel fuel within the combustion chamber is approx between 450*c - 675*c Brent

Read more

How can you increase the compression ratio of an internal combustion engine?

Compression ratio (CR) is the total volume of a cylinder at BDC (bottom dead center) divided by total volume of space at TDC (top dead center).To increase CR, you must either increase the total volume of displacement, or decrease the volume at TDC. This can be achieved by shaving the heads, incre...

Read more

What is compression ratio for petrol engine?

Different engines - different ratios, but commonly around 8 to1.

Read more

What is the average temperature inside the combustion chamber of an internal combustion gasoline engine?

Temps can be close to 3600 deg f away from surfaces. Surfaces however are kept cool by the engines cooling system and the fact that the burning mostly takes place in only 1 of the four strokes. Exhaust manifolds can reach temps of over 1800 deg. f

Read more

Is the internal combustion engine's fuel burns outside the engine in chambers called cylinders?

Internal combustion refers to an engine were the combustion process takes place inside the engine. The cylinders in question are an internal portion of the cylinder block which houses the crankshaft, connecting rods and the pistons which move up and down in the cylinder drawing in the air fuel mi...

Read more

What is the air pressure inside the top of a normally aspirated engine cylinder with an 11.5 compression ratio when the piston therein is in the power stroke and at full compression.?

Assuming an atmospheric pressure of 14.7 psia and a specific heat ratio of the air at 1.3 then the required pressure is: P = Patmp X rck= i4.7psia X 11.5 1.3= 351.74psia

Read more

How does compression ratio affect engine efficiency and performance?

Engine efficiency is increased though compression ratio by allowing a more thermodynamic energy to be converted into mechanical energy. Energy transfer is the key to efficiency.

Read more

What takes place in the combustion chamber of a gas turbine engine?

combustion it is where the fuel and air mixture burns and the expanding gasses drive the turbine

Read more

Which engine is more efficient in terms of compression ratio?

For a conventional gasoline engine, the higher the compression ratio, the more efficient the engine. US passenger cars have not had very high compression ratios for about 30 years for multiple reasons. During 1970-1972, Chrysler had the highest compression ratios in US production cars, requiring ...

Read more

What is a compression ratio?

Compression Ratio is the ratio between the original volume and the compressed volumein combustion chamber.The compression ratio is denoted as CR. It is the measure of how much air-fuel mixture is compressed during the compression stroke in the case of the gasoline engine (in the case of the diese...

Read more

What pressure ratio causes knocking in a petrol engine?

The pressure ratio does not cause pinging in an internal combustion engine. Pinging is the result of the air/fuel mixture igniying before the piston is in the propper position. Chep gas will cause pinging because it is igniting too quickly. Too high a compression ratio will do the same thing. Ing...

Read more

What is the ideal compression ratio?

Compression ratios usually range from 8:1 to 10:1.A higher compression ratio -- say, from 12:1 to 14:1 -- means higher combustion efficiency.Higher compression ratios and combustion efficiency mean more power with less fuel, and fewer exhaust gases.

Read more

Is an engine's bore a measurement of the combustion chamber or the piston?

The cylinder. When you "Bore Out" an engine block, you're making the combustion chamber wider to accommodate larger pistons to increase horsepower. That's usually mostly done in drag racers, not much use for it in a street car, unless you like supportin' the local Policemans Ball.

Read more

What is the danger of high compression in a spark ignition engine?

If the pressure is too high for the grade of fuel, you will get 'pinking' or 'pinging'. This is the term for pre-ignition. The fuel will explode instead of burning rapidly, and makes a metallic rattling or 'pinking' sound.This can damage the valves and piston crown if left to continue.High compre...

Read more

What is a Compressor Ignition Internal Combustion Engine?

I think you have a typographical error in your question. The question I believe is "What is a compression ignition engine?"The answer is:- A diesel engine is a compression ignition engine.

Read more

If an engine has a compression ratio of 7.1?

Depends on the make of engine, but that sounds about normal .

Read more

Why does diesel engine have a higher compression ratio?

The diesel engine doesn't require spark plug to generate power, instead, the high compression ratio is enough to ignite the fuel.To self-ignite the engine; the higher compression ratio is required.Moreover, the diesel is highly volatile and only air compression is enough to ignite the fuel.

Read more

What occurs in each combustion chamber during operation of a 4-stroke-cycle Otto engine.?

So what you have then is a description of Combustion Chamber status during each "stroke" portion of the 4-stroke-cycle (Otto) internal combustion engine:

Read more

What is the effect of air fuel ratio on detonation in internal combustion engine?

A leaner fuel mixture burns hotter than a rich mixture. so a leaner mixture will be more prone to detonation than a richer mixture.

Read more

What is a Spark Ignition Internal Combustion Engine?

That is your standard gasoline engine found in most cars today.Fuel/air mixture is ignited by a timed spark, controlled combustion creates power.

Read more

What unit is a compression ratio measured in?

There is no "unit". It is a ratio. Just pick a unit. Since you're likely talking about engine displacement, liters are a good unit to use.+++Engines are described in litres, but individual cylinder volumes are normally expressed in cubic centimetres (c.c.), but the compression-ratio is the same i...

Read more

How does a Compression ignition engine work?

A compression ignition engine works with Pistons and Valve openings.There is an intake valve, with lets the fuel and air into the cylinder, and the exhaust valve which allows for the escape of the combustion.The engine starter, supposedly started by a battery, gives the piston an Initial movement...

Read more

What is the compression ratio for gasoline?

It would vary between gas engines and how they were built, but most would fall between 8 1/2 to 1 and 11 to 1 compression ratio.

Read more

What is the deffintion of compression ratio?

Compression is squeezing something so that it occupies a smaller space. Ratio is the proportion between two quantities or numerical values. Click the link for a detailed explanation. Explanation below!++++Therefore a Compression Ratio is the ratio between original and compressed volumes of, norma...

Read more

What is compression ratio formula?

By definition, the compression ratio is the total swept volume of the cylinder with the piston at bottom dead center (BDC), divided by the total compressed volume with the piston at top dead center (TDC).

Read more

What is the compression ratio on a 1.4 corsa petrol engine?

For the Opal Corsa generation Corsa B, 1.4 i petrol engine, the compression ratio is 9.4. It has 60 horsepower and a 46 liter fuel tank. For the 1.4 XER, the compression ratio is 10.5. For the 1.4 i 16V ECOTEC, the compression is 10.5.

Read more

What is my compression ratio?

By definition, the compression ratio is the total swept volume of the cylinder with the piston at bottom dead center (BDC), divided by the total compressed volume with the piston at top dead center (TDC).

Read more

What happens inside a combustion chamber?

A combustion chamber is an enclosed space inside of a combustion engine in which a fuel and air mixture is burned.Burning fuel releases a gas that increases in temperature and volume.When you heat a gas, the atoms in the gas start bouncing off each other with more energy and vigor.

Read more

What's a good compression ratio?

Compression ratios usually range from 8:1 to 10:1.A higher compression ratio -- say, from 12:1 to 14:1 -- means higher combustion efficiency.Photo: Sébastien D'Amour.The benefits.Higher compression ratios and combustion efficiency mean more power with less fuel, and fewer exhaust gases.

Read more

What is the total displacement in cubic inches of a v6 engine when the compression ratio is 3-3 and 1 half Does it equal 173 cubic inches?

The compression ratio doesn't deal with the displacement, the bore and stroke do. If it's a modern engine it should say the size of the engine in liters. You can use this to convert the engine size to cubic inches. A 173ci engine is a 2.8L engine when converted.

Read more

How do you lower the compression ratio of an engine?

There are several means by which the compression ratio of an engine might be reduced although all involve extensive mechanical rework to accomplish.1) Remove the heads from the motors and grind the compression chambers of the head(s) to make the area larger.2) Install replacement pistons that hav...

Read more

How does a two stroke engine combine the four strokes of a typical internal combustion engine?

A two stroke engine combines the four strokes of a typical internal combustion engine into two strokes instead of four.

Read more

How do I change the compression ratio on my engine?

To decrease the compression ratio "remove material" from inside of the Cylinder head or piston top. This increases both the volumes by equal amount and hence the ratio gets decreased. Changing the piston head design.Changing the stroke length of the cylinder.Changing cylinder diameter.Chang...

Read more

Glowing hot spots in the combution chamber that ignite the fuel before timed ignition is called?

pre-ignition or inaccuratley, Dieselling. it is , of course a hazard, and could cause a backfire, or even an engine explosion.

Read more

What is the compression psi of a compression ratio of 16.2?

There is no direct connection between compression ratio and pressure. Ratio is a mathematical calculation of the cylinder volume from bottom center to top center. Actual cylinder pressure will depend on the volumetric efficiency of the engine. Factors the affect volumetric efficiency include rpm,...

Read more

Auto Technician A says the total volume of all the cylinders in an engine is called the compression ratio?

The volume of an engine is called displacement and is typically measured in cubic inches or liters. An eight cylinder engine that could hold 1/2 liter of water (or air) in each cylinder would be a four liter engine. As the pistons move to the top of the cylinder in an exhaust stroke, they theoret...

Read more

What affects the efficiency of the combustion chamber?

This sounds like a homework question and I don't know what your teacher wants. But here goes.And a bunch more that I have forgotten.

Read more

What is the functional relationship between compression ratio and thermal efficiency?

Compression Ratio – Otto Engine In the following section, it will be shown that the compression ratio determines the thermal efficiency of used thermodynamic cycle of the combustion engine.In general, it is desired to have a high compression ratio, because it allows an engine to reach higher the...

Read more

How many general types of combustion chambers are used in diesel engines?

Diesel Engine combustion chamber types : Swirl port combustion chamber type and Preignition port combustion chamber type.

Read more

Why compression ratio is greater than 1 in i c engine?

because a 1 to 1 comp ratio would not generateenough power to keep the engine to idle,the higher your ratio the more of a powerful stroke you will have. more power is good.a i c fuel engine will be between 9;1 to 11;1 race motors on hi octane around 14;1

Read more

What is the key difference between the piston action of an internal combustion engine and that of a compressed-air engine?

The internal combustion engine uses a fuel i.e petrol or diesel to cause compression when ignited ,when the fuel burns it causes compression of the piston. A compressed air engines power comes from an electric motor which forces the piston up and down to produce compressed air.

Read more

What is the formula for calculating compression ratio?

To calculate the ratio for your vehicle, you need to use the formula, compression ration = volume at below dead center divided by volume at top dead center.

Read more

What is diesel combustion pressure?

The diesel combustion pressure depends on various factors. The model and the type of diesel engine is important.

Read more

What is the compression pressure of a 400 sbc?

It could vary greatly depending on how the engine was built. What you want to see is all the cylinder readings be within 10% of each other.

Read more

What is the combustion chamber size of a 1994 4.3liter V8 Chevy?

There is no Chevy 4.3 V8. The 4.3 is a V6 followed by a 4.8 V8

Read more

What is the most important difference between an internal combustion engine and an external combustion engine?

in internal combustion engine combustion happens internally in cylinder and in external combustion engine combustion happens externally in boiler

Read more

What is the difference between internal combustion engine and external combustion engine?

An internal combustion engine burns the fuel inside the engine itself, i.e. gasoline burning in the cylinders.An external combustion burns the fuel outside the engine, i.e a steam engine on a locomotive.

Read more

What does compression ratio mean in car motors?

In an internal combustion engine, there are cylinders that have pistons in them. When the piston is down you have an open cylinder that has a specific size of volume that it will hold. When the piston moves back up to as high as it can, it compresses all that space into the new space and that is ...

Read more

What is the difference between the Internal combustion and the External combustion engine?

In an Internal Combustion Engine, the Fuel is burnt in the cylinder or vessel eg. Diesel or Petrol engine used in Cars.Gasoline engines, Wankel engines, diesels, gas turbines are all examples of internal combustion.In an External Combustion Engine, the internal working fuel is not burnt. Here the...

Read more

How much pressure is required to push up and down the piston of a 4cylinder internal combustion engine?

This depends on a lot of factors.Mostly though it would be the compression ratio, which is basically the ratio of the cylinder volume open/closed, and the stroke which would be the length, as well as the bore which would be the width.So how much surface it is hitting (bore) would vary the pressur...

Read more

Is a higher or lower compression ratio better?

Automotive engineers can improve fuel efficiency and fuel economy by designing engines with high compression ratios.The higher the ratio, the more compressed the air in the cylinder is.It's the same thing with compression ratios.By keeping the explosion in a smaller space, more of its power can b...

Read more

What is the problem if the combustion chamber is not properly sealed?

that would be a compression problem.

Read more

What is internal and external combustion engines?

In an external combustion engine, the fuel isn't burned inside the engine.External engines have a working fluid that is heated by the fuel.Internal combustion engines rely on the explosive power of the fuel within the engine to produce work.

Read more

What is the difference between internal and external combustion engines?

The only external combustion engine I can think of would be a steam engine. I suppose subway trains could be considered external since they receive electrical power from outside to run the electric motors.

Read more

What is the difference between external and internal combustion engines?

In an external combustion engine, the fuel isn't burned inside the engine.External engines have a working fluid that is heated by the fuel.Internal combustion engines rely on the explosive power of the fuel within the engine to produce work.

Read more

What is the correct octane rating for 10 to 1 compression ratios Is there a chart?

Depends on timing of the engine, whether the engine has aluminum or cast iron heads (aluminum dissipates heat faster, therefore allowing a lower octane), the design of the cams, and a host of other things. So no, no chart. Rule of thumb: 10:1 use 91-93 octane gas.

Read more

What happens if compression ratio is too high?

At that high compression ratio gasoline will self ignite during the compression stroke itself before the piston head reaches the top dead centre, this is a phenomenon of erratic combustion which brings a lot of damage to piston head and also the combustion chamber, temperature and pressure inside...

Read more

How does the explosion is the combustion chamber make the car move?

With combustion (explosion) the energy created has to go somewhere - so it expands within the chamber thereby forcing the piston to move downwards. When repeated rapidly and with more than once cylinder, the engine propels the vehicle, provided of course that the transmission is in the proper gear.

Read more

What is the difference between combustion and detonation as in a internal combustion?

When the engine detonates its referring to the engine giving spark to the compressed air/fuel in the cylinder, when theres combustion its simply the explosion that happens after ignition.

Read more

What does chamber volume mean in a engine?

The chamber volume refers to the compression ratio of the external combustion of the engine.

Read more

What is combustion efficiency in engines?

Most internal combustion engines are incredibly inefficient at turning fuel burned into usable energy.The efficiency by which they do so is measured in terms of "thermal efficiency", and most gasoline combustion engines average around 20 percent thermal efficiency.

Read more

What is a mix ratio in small engines?

Oil fuel mix ratio is different for different engines, please contact the manufacturerFuel air mixture is the same @ 17 to 1 by weight.

Read more

What is the combustion efficiency in an automobile engine?

It varies somewhat depending on engine design, but a gasoline engine is approximately 30% efficient due to heat, mechanical loss, etc. Despite modern engines getting about 98-99% efficiency out of the gasoline.

Read more

What is combustion in an engine?

Combustion, also known as burning, is the basic chemical process of releasing energy from a fuel and air mixture.In an internal combustion engine (ICE), the ignition and combustion of the fuel occurs within the engine itself.The engine then partially converts the energy from the combustion to work.

Read more

What is the correct octane rating for 9.8 to 1 compression ratio?

It really depends on the motor, heads(iron/aluminum), cam. For example an older iron head 350 with a small cam with 9.8:1CR will need 93 maybe even octane booster. While a small bore aluminum head engine could run 89 maybe even 87 depending on cam size.

Read more

Compression ration in diesel engine is?

Higher than a gasoline engine.

Read more

What is considered a high compression engine?

Anything over 10:1 is a high compression ratio.Anything over 12:1 is "highly compressed".87 Octane is both a high and low compression fuel.

Read more

What is the cause of combustion in car engine?

For a gas, E85, or LNG/LPG/CNG engine, it's a spark from the spark plug igniting the fuel air mixture. For a diesel engine, it's compression which causes the combustion to occur.

Read more

Is the 460 a high compression engine?

Depends on what year the engine was made. Late 60's and early 70's produced around 10.5:1. Later years could be as low as about 8.8:1

Read more

What is the compression on a 1995 wildcat 700 engine?

120 P.S.I. is acceptable low, 130 is good 135 is factory startup/breakin period required.

Read more

What is the typical low side pressure of a vehicle's AC system?

Actual readings will vary according to ambient temperature.The low-side should be near 30 PSI at 90 degrees Fahrenheit or less.Pressure that is too much lower or higher shows there is a problem.On a properly working system, high-side pressure will be about twice the ambient temperature, plus 50 PSI.

Read more

Is the compression ratio of a piston inside its cylinder measured mechanically or atmospherically?

Mechanically To put it as simply as possible. The cubic inches of a cylinder and the amount of space your compressing it into is the compression ratio.

Read more

What is the maximum compression ratio to run on 93 octane?

12.4:1. this is your final or corrected compresssion ratio(FC). By that I mean adding in corrected altitudeFC- (altitude/1000)x.02your cam selection (see Keith black pistons calculators for dynamic and static compression)and if you are running a supercharger(boost / 14.7+1) x compression ratio= F...

Read more

What is the Difference between internal combustion engines and diesel engines?

There is no difference. Both are internal combustion engines. I think I know what you're asking though. A gasoline engine uses spark ignition and a diesel engine uses compression ignition.The gasoline engine needs an spark or other heat source to ignite the fuel air mixture in the cylinders. The ...

Read more

What is the effect of compression ratio on efficiency of Otto cycle?

Thermal Efficiency for Otto Cycle A higher compression ratio permit the same combustion temperature to be reached with less fuel, while giving a longer expansion cycle.This creates more mechanical power output and lowers the exhaust temperature.

Read more

What does a PVC do and what does it stand for in an internal combustion engine?

PVC - Positive Crankcase Ventilation. Used to allow the engine to vent out pressure that is creates while operating. Generally it is vented back into the air intake system after the air filter to get "burned" in the combustion chamber.

Read more

Why is the most important difference between an internal combustion energy and an external combustion engine?

shell, safeway, arco, texaco, cheveron,

Read more

What is the difference between ignition temperature and spontaneous ignition temperature in a fuel cell?

The minimum temperature the fuel ignites self sustained combustion is known as spontaneous ignition temperature. The temperature at which the substance is preheated and burns smoothly is known as ignition temperature.

Read more

What is the internal combustion engine?

sunil is really gay and sucks a call of duty 4!!!!!!There are several types: gasoline and diesel fueled are the two main types. Within those they have various combustion cycles: 2 cycle, 4 cycle, otto cycle, atkensen cycle, wankle cycle are some that apply to gasoline engines. The thing they all ...

Read more

What are the differences of internal combustion and gasoline engine?

and internal combustion engine and a gasoline engine are the same thing.

Read more

What is the combustion temperature of a diesel engine?

Most engines run at between 195F and 220F but the fuel ignites at any temperature that is conducive to the fuel's flash point.The range is 90F to 220F.Compression ignites the fuel in a diesel engine and the temperature of the cylinder when the fuel is introduced needs to be stable to achieve a cl...

Read more

You did a compression test and have 195lbs what is the compression of the pistions?

There is no possible way to answer that question based on just PSI.Try googling compression ratio calculator. Once opening the first result you will need to enter your engine specifications to find out the answer. You will need to know the bore, stroke, gasket thickness, size of the combustion ch...

Read more

How may amps pass through the typical auto ignition switch after starting and while running?

This unanswerableThe Question is like asking how many feathers are on a typical bird.For this question: what is a typical car? That will need to be defined.

Read more

What is a combustion engine for?

Converting chemical energy energy into kinetic energy (ie movement).

Read more

In a diesel engine the airfuel mixture is ignited by?

it is ignited due to the high temperature caused by the pressure inside cylinder, when it is compressed.

Read more

What is the difference between combustible and non combustible liquids?

Combustible liquids can easily catch on fire and burn. Non-combustible liquids cannot, at least under a set of defined conditions.

Read more

What is the Use of microcontrollers in engine ignition?

They are way more dpendable then points and condensors.

Read more