What is the torque spec for the exhaust manifold on a 95 Honda Odyssey?

Cars & Vehicles
Honda Odyssey

The 1995 Honda Odyssey exhaust manifold bolt torque specification is 45 pounds. The exhaust manifold bolts should be torqued in 15 pound intervals.

Previous questionHow much does a traffic citation cost for failing to stop at a stop sign in Riverside California?
Next questionWhat is the most costly military vehicle?

Related question

What is the torque specs on an edelbrock aluminum intake manifold for a 69' Chevelle 396?

the edelbrock website should have that info.

Read more

What are torque specs for 5.7 aluminum intake manifold?

With iron heads, the stock spec for iron intakes of 30ft-lb should do. If you are going into aluminum heads, you do not want to go very tight, maybe 20ft-lb or so. AFR recommends just making them "snug" when installing an intake and exhaust headers on their aluminum small block heads.

Read more

What is the 95 blazer cylinder head torque specs?

Tighten all bolts first pass to 22 ft lbsThen long bolts 75 degreesMedium bolts 65 degreesShort bolts 55 degreesYou can also do them this way.First pass 26 ft lbsSecond pass 44 ft lbsFinal pass 66 ft lbsThe first method is the factory recommended but both will work fine.

Read more

Torque specs for 327 small block intake manifold?

Intake Manifold (Cast Iron Heads) Non- Hardening Sealer 30 ft-lbs.

Read more

What are the manifold bolt torque spec for gm 292 engine?

I have an official 1963 Chevrolet Truck Shop Manual, published in 1962 by GM. I also have the Supplement Truck Manuals for 1964 and 1966, which are meant to be used with the 1963 Manual and cover changes made in those years. 1963 apparently was the first year of the 6 cylinder 230 and 292 engines...

Read more

What are torque specs for head gasket and intake manifold for 1999 Pontiac sunfire?

The 1999 Pontiac cylinder head gasket bolt torque specification is 160 pounds. The intake manifold bolt torque specification is 90 pounds.

Read more

What is the SRS light on a Honda Odyssey?

Generally, the SRS light only flashes on when the vehicle has been in an accident.If it turns on when there has been no accident, it means the airbag system is malfunctioning and the vehicle should not be driven.

Read more

What is the torque specs on a Chevy 350?

You should always check the year of your engine before torquing any bolts.The specifications given are for the typical 350 engine.The Chevrolet 350 cylinder-head torque specification is 65 ft.-lbs.The intake installed onto cast-iron heads requires 30 ft.-lbs.

Read more

What are torque specs for cambolt on 94 ford escort?

Need More information? Which engine and will normally be found in most engine repair manuals available at local library's and www.autozone.com also for free! Good Luck

Read more

What is the torque spec for a water pump on a 2003 Buick lesabre?

3800 II V-6LONG Bolts - 2 Steps: 15FtLbs; +40degSHORT Bolts - 2 Steps: 11FtLbs; +80degMy husband is replacing the water pump on my 2003 buick lesabre and the box does not include any information for the torque specs. could you direct us on this?

Read more

What is the torque specs for Chevy 350 heads?

You should always check the year of your engine before torquing any bolts.The specifications given are for the typical 350 engine.The Chevrolet 350 cylinder-head torque specification is 65 ft.-lbs.

Read more

What is the torque sequence for the intake manifold bolts on a olds 3.1?

Driver, Buy the repair manual for the vehicle. Haynes makes excellent manuals for most vehicles. Or, barring actual purchase go to your local library and look up the information, make a copy or drawing to take with you to torque the fasteners.

Read more

On a 1987 Honda Accord is the exhaust manifold in the front facing the radiator or underneath the car?

asuming the vehicle has a 4 cylinder, the exhaust manifold would be facing the radiator. 6 cyl. would also have one facing the firewall. You can figure it out simply by tracing your exhaust system from back to front. tail pipe - muffler - exhaust pipe - catalytic converter - exhaust pipe - exhaus...

Read more

What are the torque specs for a 22r head?

get specs from your local librarys technical isle look up specs and tightening sequence.

Read more

What are the torque specs for a toyota 4ac?

For what? Without knowing, I will give you the head bolt specs. First, always use new bolts. Begin in the middle. Then go to the ends. Never tighten two bolts on the same side in sequence.. First torque them to 22ftlbs, the go around and do them again give them 1/4 turn. 90 degrees. Then do that ...

Read more

What is the torque specs on the hub assembly for 2002 alero front?

96 foot pounds for the three 13mm bolts that hold the hub, was looking for myself and found you was looking too! http://www.automotiveforums.com/vbulletin/showthread.php?p=4941184

Read more

What are the torque specs for 327 rocker studs?

50 lb/ft lubricated with oil. Check out the link I posted.

Read more

What are the torque specs for the head on a 650 Kawasaki jet ski?

what about a 08 sxr 800

Read more

Where is the stater on a 1997 Honda Odyssey?

behinder the pull starter

Read more

What are the torque specs for the heads on a 1981 305?

Head bolts are 65 lb/ft. Look at the link, "Small Block Chevy" at the right for all torque specs.

Read more

What is in a Honda Odyssey 2014?

What is in it ❓ Well, it has a 3.5 Liter 248 h.p V6 engine mated to a 6 speed automatic transmission. Want more information then click the link and read.

Read more

What are the torque specs for head bolts on a 14.5 horse power Briggs and stratton?

185 in/lbs. or 15.5 ft/lbs.

Read more

What is the bolt torque sequence for upper manifold bolts on 4.3 Vortec?

I take it you mean on a trailblazer/ envoy/ bravada..??Ok.. standing on the right side of the engine, looking at the head/ valve train and the front of the engines to your left. Locate the centre of the engine roughly tween 3rd an 4th cylinder.. that's hole 1 nearest with hole 2 across... move to...

Read more

What are the torque specs for accord 2.2 head bolts?

It is important to reach the recommended torque specs in increments by starting at the middle and working toward the ends. On the first round, you should go to 29 ft lbs, the?æsecond round, 51 ft lbs, and the third round, 72.3 ft lbs.?æ

Read more

What are the torque specks for the rocker arms on a 95 s10 2.2?

The torque specs for a 1995 s-10 rocker arm nut is 22 ft lbs.

Read more

What is the torque spec for a 1995 1.0 Geo metro spark plug?

The 1995 Geo Metro spark plug torque specification is 20 pounds. You should torque the spark plug intent pound intervals.

Read more

What is the lug nut torque spec for a 2006 Isuzu npr?

On steel wheels the lug nuts should be torqued to 80 lb/ft. On aluminum wheels torque them to 85 lb/ftDon't know the factory torque specs offhand, but for that vehicle, I'd recommend you torque them to at least 400 lbs/ft. On steel wheels the lug nuts should be torqued to 80 lb/ft. On aluminum ...

Read more

WHAT ARE THE TORQUE SPECS FOR Chevy Orlando CAR WHEELS?

2012-14 Chevrolet Orlando lug nut torque spec is 100 ft lbs.

Read more

What are the Torque spec for rod bearing on a 2.7L Chrysler Concorde?

20 ft.lbs. Plus 1/4 turn.

Read more

Torque specs for head on 1980 Yamaha YZ490?

there is no such bike yz490 didn't start till 1982 and went on to 1990 before this it was a 465 ....

Read more

What are torque specs on a 91 camaro intake?

If it is a small block V8 with cast iron heads you torque them to 30 ft/lbs.

Read more

Head bolt torque specs for a 2001 Kia Rio?

I found this on another post but thought it might help out. When tightening the head bolts always start in the center. Tighten the 2 center bolts the either diagonally or in a circular pattern work your way to the outside bolts. Diagonally is usually the best procedure. Be sure and put just a lit...

Read more

What is the torque specs on a transmission bolts of a 98 Oldsmobile eighty eight LS?

There are many different bolts on a transmission. Need to know which ones.

Read more

What is the fuel tank capacity for a 2000 Honda odyssey?

The fuel tank capacity of a 2000 Honda Odyssey is 21 gallons. This provides sufficient capacity for the vehicle to travel up to 400 miles.

Read more

What is the torque spec of a water pump on a 2002 Dodge Durango?

The 2002 Dodge Durango water pump bolt torque specification is 40 pounds. The water pump bolts should be torqued in 20 pound intervals.

Read more

Is exhaust oil leaking between the expansion chamber and exhaust manifold on a cr85rb normal?

i dont know if its normal but my cr 85 leaks there and everyone that i know had one says thiers leaked too it may not be normal but its definetly common and im sure its a very easy fix probobly a new gasget or tighter springs can help it.

Read more

What is the Head bolt torque spec for a 1994 gm 2.0 liter?

check with your local gm dealer or local auto parts store they can look it up in there books or on the computer

Read more

What is the torque specs on the oil pan of a turbo 350 transmission?

According to my haynes Gm manual... 120 inch pounds.

Read more

Are 1972 exhaust manifolds the same as 1973 exhaust manifolds?

It would depend on the type of vehicle and the size of the motor.

Read more

What is the torque spec for flywheel for Chevy S-10?

few websites i have searched have come back with a flywheel to crankshaft torque spec of 50 ft-lbs same goes for the flex plate in automatic models. pressure plate torque spec is 23 ft-lbs

Read more

What is average cost for replacement of shocks of a 2009 Honda Odyssey?

Both front strut inserts only, $600 to $700 parts and labor.Both rear struts only, $300 to $450 parts and labor.Alignment extra.

Read more

What are the torque specs for a 1996 Subaru Outback with a 2.6?

wheel torque specs are 80 foot pounds.

Read more

Torque specs for a cylinder head on a 1987 Nissan Sentra sohc?

The 1987 Nissan cylinder had bolt torque specification is 140 pounds. The cylinder head bolts should be torqued in 45 pound intervals.

Read more

Head gasket torque specs for a 2000 Pontiac sunfire 2.2L?

The short bolt torque specs for the head gasket of a 2000 Pontiac Sunfire is 43 foot pounds. The torque specs for long bolts is 46 foot pounds.

Read more

What are torque spec for Neon caliper bolt?

The torque for the brake hose to the caliper mounting bolt is 35 ft. pounds. For the adapter mounting bolt it's 16 ft. pounds. For the adapter to the knuckle mounting bolt, the torque is 50 ft. pounds.

Read more

What is the purpose of the exhaust manifolds?

A typical exhaust manifold collects the exhaust from multiple cylinders and leads the exhaust out one common opening into the exhaust pipe.It carries the exhaust away from each cylinder and routes it to the exhaust pipe where it flows to the catalytic converter and then to the muffler where the s...

Read more

What are the torque specs for the rear bub bearings on a 2000 gmc c6500 straight truck?

This bearing is NOT preloaded by a torque spec.It has a end play specification to guaranty it has enough clearance to operate safely.

Read more

What is the torque sequence on a 351 Windsor intake manifold?

just start in the middle and tighten in circler pattern

Read more

What does the code p0780 mean on a 2001 Honda odyssey?

Shift Control system fault. Most common cause is low fluid, second is contaminated fluid. If the fluid is Ok, then shift solenoids

Read more

Head bolt torque specs on a C-12 Caterpillar engine?

120ft lbs first- 160ft lbs second then mark heads turn another 1/4 turn outside smaller dia bolts are 22 ft lbs

Read more

Is there dual exhaust manifolds for v6 Dakota?

V6 Dakotas come with "dual exhaust manifolds". If your asking about exhaust systems, all I've seen are singles in and out or single in with dual tips (mufflers). The pipes to the mufflers is Y-pipe to single.

Read more

WILL 23570R16 TIRES FIT ON HONDA ODYSSEY?

If it came with 235/65/16 tires originally, and you are replacing all the tires, it will fit but the speedometer will be slightly off (3.3%). I would also check the tire load rating, to make sure it equals or exceeds the stock tire rating.

Read more

What are the torque specs for a half shaft 1999 leganza?

the half shafts about 4 inches but the head of it is where size matters. make sure there are two ball sockets below the shaft when you configure with it. cradle them with care.

Read more

What are the flywheel bolt torque specs for a 1984 F250 with a 6.9 diesel?

Don't bother with torque specs, rust and worn bolts can make the torque innacurate. Just make nicely tight with one hand on wrench (DO NOT STRIP, A 12-POINT BOXED END WRENCH IS GOOD ENOUGH). You can also put anti-seize on bolts (only a little)... you never know if you will be the next person that...

Read more

Torque specs on a head bolts for a 1991 yz 125?

The cylinder head bolt torque specification is 90 pounds. The cylinder head bolts should be torqued in 30 pound intervals.

Read more

What is the torque spec for clutch plate Chevy 1997 S10?

35 lbs/ft.1997 S10 4 cylinder engine pressure plate to flywheel bolts, 33 ft lbs.1997 S10 V6 engine pressure plate to flywheel bolts, 29 ft lbs.

Read more

What is the caliper mounting bracket bolts torque spec for an 2004 Pontiac Grand Am?

Front caliper bracket to knuckle, 85 ft lbs. I also use a drop of blue "Loctite" thread locker on clean threads.

Read more

What are the cylinder head torque specs for a 1996 Ford Explorer 6 cylinder?

For the 1996 Ford Explorer 4-wheel drive 4.0 liter 6-cylinder engine, the head bolt torque for step one is 44 ft. lbs. For step two, the torque is 59 ft. lbs., and for step three, turn an additional 80 to 85 degrees.

Read more

What are the torque specs for a 2000 Subaru Outback transmission pan?

Go to you local library and get the repair book, its free to use or a few cents to copy.

Read more

What does the SRS light mean on a 2004 Honda Odyssey?

Posted: 12/22/2011.I actually dealt with this last week at my shop.The SRS light is a warning light for your supplemental restraint system (airbags).An SRS light means that there is a problem in the system.The first thing I would check is the fuse for the SRS unit.

Read more

What does the SRS light mean on a 2003 Honda Odyssey?

SRS means Supplemental Restraint System Indicator.This light indicates that there is a problem with the airbags and seat belt tensioners and they may not deploy in case of an accident.

Read more

What are the rod and main bearing torque specs for a 1995 Toyota 4Runner 3.0 v6?

The 1995 Toyota 3.0 liter engine main bearing torque specification is 160 pounds. The rod bearings torque specification is 120 pounds.

Read more

What is a 4 2 1 exhaust manifold?

From the cylinders, 4 individual exhaust passages converge into 2 passages and finally collect into 1.

Read more

What are the cylinder head torque specs on a 1990 Toyota Corolla?

Depending on the model/engine type, the cylinder head torque specs for a 1990 Toyota Corolla are: For the 4AFE (1.6) coupe/sedan/wagon: 44 ft lbs For the 4AGE (1.6) GTS coupe: 1st: 22 ft lbs 2nd: additional 90 degrees 3rd: additional 90 degrees

Read more

What is the Torque specs for the nut on the spindal that holds in your wheel bearing for a 1997 ford f150?

You tighten it down until it is snug ( hub will be stiff ) and back it off 1/4 turn. The slots on the castle nut will line up with the hole for the cotter pin. You tighten it down to set the bearings into place, then back it off till it spins freely without play.

Read more

What are the head bolt torque specs for a 2003 ford F250 V10?

call up your local parts store. theyll tell you for free

Read more

What tis the part number for a 91geo prism exhaust manifold?

Single overhead cam 94856515Dual overhead cam 94845263

Read more

What is the purpose of an exhaust manifold?

Typically made of stainless steel, cast-iron or heavy-gauge steel, the exhaust manifold directs exhaust gases from multiple cylinders to a single exhaust pipe.In so doing, the exhaust manifold also helps to minimize leakage of heat, air and gases.

Read more

When to change timing belt on 1995 Honda odyssey?

The factory recommended mileage/time interval for replacing the timing belts on the Honda Odyssey is 10 years or 105,000-miles, whichever comes first. That being said the type of driving, environment, how often the engine was run, and so on can create conditions where a much earlier interval is a...

Read more

What size gap should the spark plug have on a 2000 Honda Odyssey?

.044" for most brands.

Read more

What are the Dodge Ram torque spec front drive shaft?

I can Not understandNot enough info. Need to know the year, model and type of suspension it has, with independent suspension or with link/coil suspension.

Read more

Head and cam torque spec for 1997 1.8 kia sephia?

The 1987 Kia 1.8 liter engine had bolt torque specification is 120 pounds. The camshaft bolt torque specification is 90 pounds.

Read more

How do you disable the horn in a Honda odyssey?

Pull the fuse or the relay.

Read more

What is the actual cash value of a 2003 Honda Odyssey EX L?

Your vehicle, in good condition, with 150,000 miles, is worth about $3000 trade in value and $4000 private party value. This value could be more or less depending on factors like mileage, and overall condition.

Read more

Where do you find the on-board diagnostic port on a 2003 Honda Odyssey?

It is important to know the location of all electrical parts of a car. The OBD port of the 2003 Honda Odyssey is found under the dashboard, on the right side of the center console.

Read more

What is front hub nut torque spec for 2005 Nissan x trail?

waths is the torques specification for a bearing nissan xtrail 2005 back

Read more

Where do you fill the transmission fluid on a 2002 Honda Odyssey?

you have to put it in the dipstick hole.

Read more

How can you disable the alarm system on a 2002 Honda Odyssey?

To disable the alarm system on the 2002 Honda Odyssey, just use the key fob to turn the system off. You can then use your vehicle's manual to learn how to disable the passive alarm system. This generally involves a series of steps that include turning the ignition key on and off and honking the h...

Read more

Is it safe to drive a car with spilled oil on the exhaust manifold?

Wipe off what you can and the rest will dry as the manifold heats up. There will be a noticeable stink as the spilled oil dries up. It should clear after a good drive. On the other hand, a continuous oil leak dripping on or near the catalytic converter could catch fire.

Read more

Is it normal for black soot to be around exhaust manifold for a 2004 trailblazer LS?

No. This means that the manifold has an exhaust leak.

Read more

What are the torque specs on the 1989 Nissan 2.4 Z24S engine?

I believe that the torque specs on it is 137 ft-lbs at 2400 rpms.Hope this helped!

Read more

Whats the head torque specs to use on 1998 mercury mystique 2.0?

wat are the head bolt spec on a 98 mercury mystique 2.0 4 cyl anyone knows were can i get this info thanks

Read more

Why would all four brakes smoke on Honda Odyssey?

It sounds like the brake system is not releasing, as if you kept your foot on the pedal. Check to see that the pedal is coming all the way up, and that the master cylinder isn't sticking and keeping the brakes on.

Read more

Can having a new exhaust fitted damage the inlet manifold?

Only if the mechanic is abusive and does not follow proper procedure

Read more

What are the car specs of the Honda Civic VTec?

The 2013 Honda Civic VTec comes with 201 horse power, a 4 cylinder engine, and a aluminum allow engine block. It has a one touch moon roof feature 5 inch LCD screen, and has a combined gas mileage of 25 mpg.

Read more

What is the problem if a 95 Honda Accord is constantly shaking and the check engine light comes on?

The problem could be many things. With the check engine light coming on, it could be an internal issue in the engine, or broken engine mounts causing the vibrations. The shaking could also be caused by a separate issue from the engine, including a loose tire, or an out of balance tire, or bad sus...

Read more

How do you reset the SRS light on a 2005 Honda Odyssey?

Read more

Is the exhaust manifold the same for a left and right hand drive Jeep Wrangler Sport TJ 4.0L 1998?

It should be the same.. the standard jeep(left hand drive) the intake and exhaust are on the left side of the engine as well, so there is no need for a different manifold. so 99 % sure its the same manifold

Read more

Can you put a trailer hitch on a 2005 Honda Odyssey?

Yes, you can go to the dealer, or save money and stop by a uhaul dealer or truck/trailer accessory store.Yes, and you can get one right here. www. etrailer. com/hitch-2005_Honda_Odyssey. htm remove the spaces from the address.

Read more

How much does it cost to fix a sliding door on a Honda Odyssey?

Know what price you should pay to get your vehicle fixed.The average cost for a Honda Odyssey power sliding door motor replacement is between $1,461 and $1,515.Labor costs are estimated between $203 and $257 while parts are priced at $1258.Estimate does not include taxes and fees.

Read more

Do the new linkage bolts on a 99 Tahoe front stabilizer need to be torqued to a certain spec?

No, unless you are planning on racing.

Read more

What are the head bolt torque specifications for a Honda Accord 2.2L engine?

The head bolt torque specifications, for your Honda Accord 2.2 liter engine, is 120 pounds per square inch. The head bolts should be torqued in 30 pound intervals.

Read more

What are the functions ofengine inlet and exhaust manifolds?

Inlet manifolds are actually called intake manifold and this is to allow air to be injected into the fuel for either a rich or lean mixture for either performance or gas mileage (which can be adjusted). The Exhaust manifold is used to expel your burnt fuel, or air/fuel mixture, during the exhaust...

Read more

What does a leaking exhaust manifold sound like?

1.Excessively noisy engine.A faulty exhaust manifold gasket will produce an exhaust leak that will sound like a hissing or tapping sound coming from the engine.The sound may be especially pronounced during a cold start or during acceleration.

Read more

What are the head cam torques specs of a 1993 ford probe 2.0L double overhead cam?

Valve Camshaft Wheels/Pulley(s) = 50-60nm, Bearings Over Valves = 11-14nm ... by the way this engine only has a single head not two...

Read more

Looking for torque spec for 2001 forester front drive axle nut?

The 2001 Forrester front drive axle nut torque specification is 90 pounds. The front drive axle nut should be torqued in 45 pound intervals.

Read more

Can you get a labeled exhaust diagram or a picture of the exhaust for a 1994 Honda Civic hatchback?

yes you can, I am not sure what the site was, but google "Honda civic club." They have diagrams of just about everything that you will need.

Read more

Your 1997 ford F150 exhaust manifold is getting red hot?

You may have a problem with the fuel/air mixture. Your engine may be running way too rich. The raw fuel is being dumped into the exhaust manifold and burning there. But I think you may have a burned or leaking exhaust valve or two on one side, or poor combustion due to bad wires, plugs etc.

Read more

Does a Holden 202 blue inlet and exhaust manifold fit on a 202 red motor?

pretty sure they are not compatible as the blue motor head has more ports

Read more

How much does a 2001 Honda Odyssey weigh?

The curb weight (no passengers or cargo) of a 2001 Honda Odyssey EX 4 dr mini van is 4,288 lbs.

Read more