What causes distributor go bad?

Cars & Vehicles
Distributors and Distributor Caps

Normal wear and tear.

Basically it is wear on all the moving parts.

Previous questionWhat SUV starts with the letter R?
Next questionDoes low tire pressure causes squeaking?

Related question

Do distributor caps go bad?

Since the distributor rotor and cap can go bad over time because they are located in a harsh environment, it is important to know the symptoms this part will give off before it completely fails.Signs you need your distributor rotor and cap replaced include: The Check Engine Light comes on.

Read more

Can a bad distributor cause no start?

A faulty engine distributor won't spark, which will either prevent the engine from starting or cause it a running engine to fail.In order for the ignition system to work properly it is important to keep the engine distributor operating at maximum efficiency.

Read more

Can a bad distributor cause engine power failure?

Yes, a bad distributor can cause the engine to fail to run, the distributor (distributes) a spark to the spark plugs that ignite the air/fuel mixture, if it is malfunctioning there might be no spark at all, there may be spark at only a few spark plugs, or the output may be intermittently bad whic...

Read more

What causes gasoline to go bad?

There are many things that can cause gasoline to go bad. Time (decrease in volatility), oxidation, or water contamination are all culprits.

Read more

What causes a starter to go bad?

HOW STARTERS GO BAD.Oil/Fluid Soaked: Signs of oil, grease or corrosion are signs of a leak in the vehicle.Broken Gear: When you see a pinion gear with severely damaged teeth all the way around, it is typically from improper contact with the starter ring gear.This is usually caused by a faulty ig...

Read more

What causes wheel bearings to go bad?

The main reasons that a wheel bearing fails are: Faulty installation – inappropriate tools such as a hammer or an impact wrench can cause damage to the exterior and or interior of the wheel end bearing causing the wheel bearing to fail prematurely.

Read more

What causes a flywheel to go bad?

This phenomenon is sometimes caused by a failing pilot bearing or brushing in the flywheel, but it can also be produced by problems with the crankshaft assembly.Many causes of clutch chatter originate with the clutch disc, but grooves in the flywheel or missing or damaged dowel pins can be the so...

Read more

What causes bushings to go bad?

If your bushings are made of rubber, high heat may cause them to crack and harden over time.If bushings allow excessive roll on your vehicle, this can cause them to twist and ultimately tear.Both of these will cause the bushings to go bad and potentially fail.

Read more

What causes crankshaft bearings to go bad?

Crankshaft bearings can wear out due to: excessive heat (if the oil doesn't provide sufficient cooling) drying out due to oil leakage, blockage or otherwise poor circulation (also sometimes caused by incorrectly sized or fitted bearings) metal-on-metal contact (as a result of drying out from poo...

Read more

What causes ball joints to go bad?

When debris and water are able to get into the socket, ball joints wear down much faster because of the declining quality of the lubricant.Ball joint failure can be catastrophic.If the wear becomes bad enough, the stud may separate from the housing.This can cause immediate loss of control of your...

Read more

What causes an engine to go bad?

lack of good maintenance.there are lots of reasons, what exactly do you mean?

Read more

What causes a solenoid to go bad?

Bad wiring instances include terminals that are left loose or connected the wrong way.It happens when extremely high currents flow to or through the solenoid, and for too long.It can be caused by instances where the ignition switch is left in the 'start' position for long.

Read more

What causes a stator to go bad?

There are a few things that may cause a stator to fail.Too heavy of a load when operating accessories (winch,heated grips,headlights, etc).If working several of these items at one time (plowing/pulling/possibly stuck at night) you would overload the system.This could cause either the stator or re...

Read more

What would a bad distributor do?

1.Your check engine light is on: If your car's computer detects a problem that could affect emissions, such as a misfire caused by a bad distributor, it turns on the check engine light.2.A faulty distributor can keep the spark from happening, resulting in an engine that cranks but doesn't start.

Read more

Can distributor cause misfires?

The distributor cap of an ignition system is one possible cause of many for misfires. Other possible sources to investigate are the distributors cap and gears. The flow chart of diagnosing misfires also include the coil, capacitor (if applicable), ignition wires and the spark plugs.

Read more

What happens when the distributor goes bad?

It could short out the coil voltage and cause a faulty connection inside the terminal of the distributor cap.The result is a misfire in the spark plugs.Look for any cracks or carbon trace in the cap.Inspect the condenser; the engine will not function if it is broken.

Read more

What happens when distributor cap goes bad?

Your car keeps stalling: A failing distributor can prevent adequate voltage from reaching the spark plugs.Since the engine needs that spark to run, a bad distributor can result your car stalling when it idles.

Read more

What causes a fuel pump relay to go bad?

There are different reasons due to which the fuel pump relay goes bad.There is a winding in the relays which can get burned due to a short as a result of high current or high voltage.There may be something wrong behind the scenes that could cause a burned relay winding.

Read more

What causes a voltage regulator to go bad?

Other causes for a dead regulator rectifier center on the battery.Ground connections are important for good voltage, and if there is faulty voltage, the regulator rectifier can run hot.Bad grounding, corroded battery connection and poor or loose battery connections will cause faulty voltage.

Read more

What would cause a crank sensor to go bad?

Faulty wiring harness – Loose wiring, oil or debris can cause incorrect voltage, ground or return circuit problems that can lead to wiring harness problems.This voltage disruption or wear and tear on the wiring may cause the crankshaft sensor to go bad.

Read more

What cause your tires to keep going bad?

Your alignment could be off. Meaning your tires are either facing out a bit, or facing in a bit. This can cause your tires to go bad. Your local garage should be able to do a alignment on your vehicle to straighten things up.

Read more

What can cause an Electonic Control Module to go bad?

Electrical short, factory defect, vibration, moisture, or accident.

Read more

What causes a valve cover gasket to go bad?

The valve cover gasket is very delicate and prone to oil leaks.Over time the gasket becomes brittle and will crack due to exposure to dirt, debris, heat and other elements.When this occurs, the gasket can lose its integrity and leak.

Read more

What would cause a transfer case to go bad?

Vehicle jumps in and out of four-wheel drive This is commonly caused by broken parts inside the transfer case that control this operation.The parts become worn out prematurely due to the leaking fluid caused in many cases by the output shaft seal.

Read more

What causes an oil pump to go bad?

Increased Temperature A bad oil pump can lead to an increase in engine operating temperature by restricting normal engine oil flow, reducing engine oil lubrication and increasing engine friction, which leads to an increase in engine operating temperature.

Read more

What can cause a flywheel to go bad?

This phenomenon is sometimes caused by a failing pilot bearing or brushing in the flywheel, but it can also be produced by problems with the crankshaft assembly.Many causes of clutch chatter originate with the clutch disc, but grooves in the flywheel or missing or damaged dowel pins can be the so...

Read more

What causes a fan clutch to go bad?

Attached to the engine's water pump a fan clutch can go bad in one of two ways.The clutch fails to engage no matter how hot the engine becomes.This condition will cause the engine to overheat because the fan fails to pull the necessary air through the radiator that cools the engine by the use of ...

Read more

What causes a camshaft position sensor to go bad?

Faulty wiring harness – Loose wiring, oil or debris can cause incorrect voltage, ground or return circuit problems that can lead to wiring harness problems.This voltage disruption or wear and tear on the wiring may cause the crankshaft sensor to go bad.

Read more

What causes an o2 sensor to go bad?

O2 sensors that are failing tend to read lean, which causes the fuel system to run overly rich to compensate.The result is increased emissions and fuel consumption.The same goes for any O2 sensor that has a bad internal heater circuit.O2 sensor failures can be caused by various contaminants that ...

Read more

What can cause a starter to go bad?

The misalignment is usually caused by an existing fuel or ignition timing problem.This can also cause severe damage to the nose cone and/or the starter driver assembly.Poor Grounding: The mounting bases are a key part of the starter motor's ground.These bases provide the electrical ground path to...

Read more

What causes a water pump to go bad?

Water pumps wear out over time, but the following things will speed up the process: Bad/wrong coolant:Contaminated or incompatible coolant can cause corrosion inside the water pump.Worn/improperly installed belt:A belt that's either misaligned or too tight can make the water pump seize.

Read more

What would cause a solenoid to go bad?

Bad wiring instances include terminals that are left loose or connected the wrong way.It happens when extremely high currents flow to or through the solenoid, and for too long.It can be caused by instances where the ignition switch is left in the 'start' position for long.

Read more

What causes the tensioner pulley to go bad?

There are three sources to belt tensioner failure. The first is through routine wear and tear of the drive system, which is inevitable. Other failure include failure of the pulley bearing resulting in noise, and weakening of the spring loaded assembly itself.

Read more

What causes a cylinder head to go bad?

The most common cause of cylinder head cracking is overheating.This can cause the head gasket to fail, which may lead to cylinder head cracking as the components warp and pressure begins to leak.All drivers should properly maintain their vehicles to prevent overheating.

Read more

What causes a steering rack to go bad?

Another common rack and pinion steering problem is that the bushings and bearings might wear out, leading to excessive slipping and a loose feeling in the steering wheel when driving.If there is a leak within the system, power steering fluid can slowly drain out.

Read more

What would cause my ECM to go bad?

Corrosion or damage due to moisture is one of the main reasons for ECM failure.Corrosion can enter the ECM through the wiring harness and moisture can enter by a failure in the seals in the ECM itself.This happens over a period of time (5 to 10 years) due to the ECMs exposure to the elements.

Read more

What causes a car computer to go bad?

Vibration and Stress.Vibration as well as thermal stress has also been known to cause control modules to go bad.This is because they can cause tiny cracks to form in the control module's circuit boards.However, unlike water damage, this type of damage to a control module is repairable.

Read more

What can cause a throttle position sensor to go bad?

Unstable Engine Idle: Faulty position sensors can cause sporadic idle conditions due to fluctuating airflow.Warning lights: The check engine light is designed to warn you when any sensor goes bad.If the check engine light turned on in your car, then it's important to check it out before the issue...

Read more

What can cause an ignition control module to go bad?

Overheating is a common indicator that you could be having an ignition module problem.Ignition modules that are overheating will soon completely cease to function and in the meantime can cause cause electrical shorts, engine stuttering, lower gas mileage, power loss, stalling, and gasoline odors ...

Read more

What causes a starter solenoid to go bad?

It could be a result of a starter solenoid that's broken or a defective solenoid-starter connection.Or it can be a case of decreased electrical conductivity due to corrosion, dirt, and breakages.It indicates burnt out contacts that remain closed even after the ignition switch is taken back to the...

Read more

What causes a canister purge valve to go bad?

If the canister purge solenoid starts to go out, the Check Engine light will come on and your car will not pass an emissions test.In addition, the buildup of fumes inside of the canister can cause your vehicle to stall or misfire.Vehicle fails the emissions test.Stalling vehicle due to a leak in ...

Read more

What causes a window regulator to go bad?

Window malfunctions are typically caused by a faulty window regulator (also called a window track), or a broken motor, cable pulley or window switch."The window regulators are not made to break ice free, and it prematurely wears out the window regulator mechanism." Power window issues can be inte...

Read more

What causes a relay switch to go bad?

There is nothing special about a fuel pump relay.Relays are a way to use a small or low voltage signal to close contacts that will pass a much higher voltage or current.It is a switch.If the signal coil is burned or shorted it is probably because the signal was at too high a voltage, or at too hi...

Read more

What can cause a regulator rectifier to go bad?

General Causes for Failure There are different reasons why the regulator rectifier fails.Ground connections are important for good voltage, and if there is faulty voltage, the regulator rectifier can run hot.Bad grounding, corroded battery connection and poor or loose battery connections will ca...

Read more

What can cause a voltage regulator to go bad?

A leaky diode also can allow current to drain out of the battery through the alternator when the vehicle is not being driven.A faulty voltage regulator can also cause charging problems.Internal voltage regulators also can fail from too much heat.

Read more

What causes a brand new alternator to go bad?

He adds that fluid leaks in the alternator or a tight belt can also cause damage to the alternator bearings, causing premature wearing.Gunning says when the alternator goes bad, the electronics try to draw all of their power off the battery, which can cause the battery to die as well.

Read more

What causes control arm bushings to go bad?

There are many signs of a failing ball joint or control arm bushings including: Worn bushings or ball joints can cause wheel shimmy, which may cause vibrations that are felt in the steering wheel.Vibrations may increase during acceleration and smooth out at higher speeds.

Read more

What causes the harmonic balancer to go bad?

To balance the vibrations and resonance, the mass element resists the acceleration of the vibrations and the energy element absorbs them.Over time, the crankshaft harmonic balancer can go bad from constant exposure to chemicals, the elements, or from old age.

Read more

How can you tell if distributor bad?

You wont get any fire at all, or the vehicle will not keep timing

Read more

What are the symptoms of a bad distributor cap?

Usually a faulty distributor rotor and cap will produce a few symptoms that alert the driver that service may be required. Engine misfires. Engine misfires can occur for a number of reasons. Car doesn't start. Check Engine Light comes on. Excessive or unusual engine noises.

Read more

What are the signs of a bad distributor cap?

Bad Distributor Cap Symptoms Yelling Noises. Squealing noise from the car is the first sign of a bad distributor cap. Difficulty in Starting. Some of the bad distributor cap symptoms. Shaking. You might have experienced extreme shaking or vibration when starting or shifting the gears. Stal...

Read more

What are the symptoms of a bad distributor?

Usually a faulty distributor rotor and cap will produce a few symptoms that alert the driver that service may be required. Engine misfires. Engine misfires can occur for a number of reasons. Car doesn't start. Check Engine Light comes on. Excessive or unusual engine noises.

Read more

What are the signs of a bad distributor?

Bad Distributor Cap Symptoms Yelling Noises. Squealing noise from the car is the first sign of a bad distributor cap. Difficulty in Starting. Some of the bad distributor cap symptoms. Shaking. You might have experienced extreme shaking or vibration when starting or shifting the gears. Stal...

Read more

Can a breaker going bad cause lights to flicker?

Faulty Connections A bad connection in your lamp or fixture's on-off switch can result in flickering.Troubleshoot the connections by wiggling the on-off switch.If your lights dim as you do this, you probably have a bad switch.In-line cord switches are easy to replace.

Read more

What are symptoms of a bad distributor cap?

Usually a faulty distributor rotor and cap will produce a few symptoms that alert the driver that service may be required. Engine misfires. Engine misfires can occur for a number of reasons. Car doesn't start. Check Engine Light comes on. Excessive or unusual engine noises.

Read more

What would cause the distributor to leak heavily?

If the distributor cap is cracked it will leak and if it gets damp out it may not allow your car to start. Also, there is rotar inside the distributor and if it is worn out it will cause the current to not glow properly to the spark plug wires.

Read more

How do I know if my distributor cap is bad?

Bad Distributor Cap Symptoms Yelling Noises. Squealing noise from the car is the first sign of a bad distributor cap. Difficulty in Starting. Some of the bad distributor cap symptoms. Shaking. You might have experienced extreme shaking or vibration when starting or shifting the gears. Stal...

Read more

What would cause a motorcycles ignition condenser to constantly go bad?

If it repeatedly fails you have excessive heat, wrong spec condenser, its getting wet, the voltage is incorrect off the ignition (or magneto if you have one that primitive)or you may have a bad plug wire or coil causing the spark to "back up" into the condenser. ( How it was described to me in th...

Read more

What would cause an alternator to go bad in less than 1 year?

Mechanically or electrically?T The belt tension was too tight and caused the alt bearings to fail early. You jumped it off with revesed battery ca

Read more

What causes a wheel bearing to go bad on a car hauler trailer?

There are 2 main reasons bearings "GO BAD" on a car hauler.Number 1 is lack of grease/The correct HIGH temperature grease! and the 2nd is overtightening the bearing lock nut.As the wheels turn temperatures increase and bearings expand,this causes the bearings to grind into or gall the races causi...

Read more

What causes the harmonic balancer in the car engin to go bad?

Harmonic balancers are composed of 2 elements: A mass of metal proportionate to the engine in the respect of reducing the acceleration vibration from the pistons firing, and a energy dissipating element, such as fluid, rubber or a clutch. If the mass of the balancer becomes fatigued and cracks, t...

Read more

What causes bad suspension?

An underinflated tire is a common reason for your car pulling, and a problem easily fixed.Poor alignment means uneven tire wear, annoying pulling, a constant fight with the steering wheel, and even decreased gas mileage.Your vehicle could be pulling for any number of reasons: Uneven tire pressure.

Read more

Does distributor go clockwise or counterclockwise on a 1991 Chevy?

ive got a 87 gmc it runs clockwise

Read more

What causes bad wheel bearing?

The main reasons that a wheel bearing fails are: Faulty installation – inappropriate tools such as a hammer or an impact wrench can cause damage to the exterior and or interior of the wheel end bearing causing the wheel bearing to fail prematurely.

Read more

What causes bad wheel alignment?

There are three main causes of wheel misalignment, these are: Sudden jarring or heavy impact caused by hitting something, such as a pothole, bumping a curb, or a road accident.Worn parts caused by wear and tear. Height modification, when suspension has not been changed to suit.

Read more

Would a rear end accident cause the mass airflow sensor to go bad?

It is definitely possible that being rear ended can cause the mass airflow sensor to go bad. If the exhaust system has been damaged, it will effect the airflow. Also the impact itself may have jarred the sensor loose.

Read more

Can a bad wiring cause the brake lights to go on on the dashboard?

Yes it can but that is rare. The more likely problem is one of the following:

Read more

Can a rear end accident cause the front wheel bearing to go bad?

no.not if its a car accident

Read more

Can a bad speed sensor cause it to go in limp mode?

The VSS can set a hard code, yes. Anytime the check engine light is on steady, the vehicle is in" limp mode". Meaning that its computer can not go into "closed loop operation" and none of the imput sensors are being addressed , your running on pre-set parameters as in a cold start.

Read more

Can the key being left on cause the starter to go bad?

Depending on the vehicle year it can keep power going to the distributor and possibly ruin it. The starter only gets engaged when your turn the key past "start" position.

Read more

What would cause fuel gauge bad reading?

a couple of things could cause this. depends on what kind of car. the wires could some how be shorting out to the guage itself. the guage could b bad. if the fuel pump is in the tank you will have a floater in there that could be off or the pump itselfcould b bad. sometimes you can oil the needle...

Read more

What makes a car battery go bad?

Approximately 50% of premature car battery failures is caused by the loss of water for normal recharging charging due to the lack of maintenance, evaporation from high under hood heat, or overcharging.Positive grid growth and undercharging causing sulfation also cause premature failures.

Read more

What makes a speed sensor go bad?

Over time, the transmission speed sensor can go bad due to wiring issues or just outright failing due to it constantly being used every time you are driving your vehicle.If the sensor is magnetic, it can go bad from iron sticking to the tip of the sensor, which will cause an inaccurate reading.

Read more

What makes a blower motor go bad?

The blower motor may seem to be to blame when air flow becomes notably decreased, when if fact, the fault lies elsewhere.Insufficient flow at all blower speeds might be caused by a clogged air intake screen.Leaves, or other debris that obstruct the screen can make the blower motor efforts seem fe...

Read more

What happens when struts go bad?

2) Nose dive when braking.This is a common issue in larger vehicles when a shock or strut goes bad.No, your vehicle will not flip over like it does in the movies when this happens, but this can be a safety issue.In severe cases, there can be longer braking times and a momentary loss of steering.

Read more

What can a bad idler pulley cause?

If the surface of the idler pulley wears, or the pulley seizes or binds it may cause the engine belt to squeal as a result of it rubbing against the surface of the pulley.In some instances a bad pulley may bind or slip and cause the belt to squeal when the engine is first started.

Read more

What can a bad fuel filter cause?

A severely dirty or clogged fuel filter can cause the vehicle to experience several engine problems: Misfires or Hesitation: Under heavier loads, the clogged fuel filter may cause the engine to randomly hesitate or misfire.This occurs as particles clog the filter and deplete the fuel supply going...

Read more

What causes bad smell from car exhaust?

The smell of rotten eggs is due to a compound called hydrogen sulfide.This comes from the small amount of sulfur that is present in the fuel.Two other causes of rotten eggs besides a broken catalytic converter include an engine that is running too hot or a broken fuel pressure regulator.

Read more

What can a bad coil pack cause?

missing at low or high revs or breaking down[ lack of power ] under load have a look at the engine running in the dark somtimes you can see the spark track across the coil to earth

Read more

What causes a bad battery connection?

If your vehicle won't start, it's usually caused by a dying or dead battery, loose or corroded connection cables, a bad alternator or an issue with the starter.It can be hard to determine if you're dealing with a battery or an alternator problem.

Read more

What can a bad air intake cause?

Reduction in engine performance The cold air intake also uses an engine air filter, which when clogged or dirty can cause a reduction in power, acceleration, and fuel efficiency.In more severe cases, a dirty air filter may also cause problems with starting the vehicle.

Read more

What makes ignition module go bad?

The number one reason that ignition modules go bad is because of heat.On most of the cars that have a recurring problem with this, they have the original distributor in the car.As the distributor ages and wears, the bushing in the shaft goes goes bad and starts to cause excessive heat.

Read more

What makes a starter go bad?

Loose Electrical Connection: When the electrical connection to the starter motor from the battery is not tight, it can cause arcing and burning.Melted Terminal: Cranking an engine for longer than 10-12 seconds causes critical electrical connections to become overheated and can cause them to melt.

Read more

Do bad rims cause bad alignment?

The short answer is yes.The rim itself can vibrate excessively on the axle which could loosen the components which maintain the alignment. This could happen gradually and go unnoticed for awhile. Chances are better bad tires can vibrate which is why they are balanced upon installation. Your tire ...

Read more

What makes an alternator go bad?

Internal parts can wear out or burn out.

Read more

What makes crankshaft sensor go bad?

Faulty wiring harness – Loose wiring, oil or debris can cause incorrect voltage, ground or return circuit problems that can lead to wiring harness problems.This voltage disruption or wear and tear on the wiring may cause the crankshaft sensor to go bad.

Read more

What happens when rear brakes go bad?

One of the first symptoms of bad or failing drum brakes is unusual brake pedal feel.If the brake drums are worn excessively they can cause vibrations that may be felt in the pedal.Worn drums may also cause shuddering or pulsating that will become noticeable once you step on the pedal.

Read more

What makes engine mounts go bad?

The most common reason for a broken motor mount is aging and use.The rubber is susceptible to dry rot from the constant temperature changes in the engine compartment.

Read more

What makes an ECM go bad?

Corrosion or damage due to moisture is one of the main reasons for ECM failure.Corrosion can enter the ECM through the wiring harness and moisture can enter by a failure in the seals in the ECM itself.This happens over a period of time (5 to 10 years) due to the ECMs exposure to the elements.

Read more

What makes a ECT sensor go bad?

A faulty sensor can confuse the computer, keeping it from providing enough fuel.As a result, the engine may hesitate or stall.3.You're getting poor gas mileage: Until the vehicle is warmed up, the car's computer relies on information from the coolant temperature sensor for fuel control.

Read more

What makes a car thermostat go bad?

Still, a failing thermostat is not the only cause for an abnormal engine operating temperature.Other reasons include low coolant level, a bad water pump, a worn out or loose water pump belt, cooling system leaks, a clogged radiator, a failed radiator fan and a collapsed radiator hose.

Read more

What makes a clutch go bad?

Sticking or binding in the pedal linkage, cable, cross shaft, or pivot ball are common causes.Sometimes a blockage or worn seals in the hydraulic system can also cause a hard clutch.Another problem associated with clutches is a worn throw-out bearing, sometimes called a clutch release bearing.

Read more

What problems can a bad solenoid cause?

Bad Wiring Poor and hurried wiring lead to either inadequate current supply to the starter solenoid or a more dangerous problem of shorting.Both can make a starter solenoid to malfunction and cause starter system problems.Bad wiring instances include terminals that are left loose or connected th...

Read more

What happens when motor mounts go bad?

There are three general symptoms of a bad or failing motor mount: Worn, damaged, or broken motor mounts can cause clunking, banging, and other impact type sounds as a result of the weight of the engine shifting around.Excessive vibrations: Another symptom of a bad or failing motor mount is exces...

Read more

What makes a fan clutch go bad?

Symptoms of a Bad Fan Clutch If the fan clutch is going bad or has failed, there are a couple of ways you may notice.Engine overheating at low speed or when stopped is the most-common fan clutch failure symptom.When cruising, the vehicle moving through the air pushes air through the radiator, co...

Read more

Do carburetors go bad?

If there is too much fuel, the engine can flood, run poorly, have bad fuel economy, or become very smoky while running.This is called running rich.The carburetor plays an important part in keeping your vehicle in smooth operating condition.Problems with the carburetor are often attributed to the ...

Read more

Does gas go bad?

Like a wine without a cork, gas can go bad when it sits around mingling with air.Fuel actually starts to turn nasty after 30 days.Since your car's fuel system is not an airtight container, precautions have to be taken for long-term storage.The easy solution is an additive called a fuel stabilizer.

Read more

What is distributor cap?

Distributor caps and rotors are responsible for passing the voltage from the ignition coils to the engine's cylinders in order to ignite the fuel-air mixture inside and power the engine.The coil connects directly to the rotor, and the rotor spins inside the distributor cap.

Read more

What causes a battery to go dead?

battery no longer can store a electrical charge, a charging system failure, a parasitic draw,

Read more

What causes tail lights to go out?

Common reasons for this to happen: Sometimes when a taillight lens cracks or breaks, it can allow moisture to enter the lens and cause a short circuit, blowing the fuse.Burned Out Bulbs: In the case where only one of your rear lights appears to be out, the cause is most likely a burned out bulb.

Read more