Routing new serpentine belt on 94 Plymouth Voyager?

Cars & Vehicles
Plymouth Voyager

When routing a new serpentine belt, make note of how the old belt was routed. Take a picture of the belt routing if possible. Also most cars have a sticker under the hood with the routing on it.

Previous questionRuns at a idle and stalls when you accelerate?
Next questionWhat are the torque specs for accord 2.2 head bolts?

Related question

1999 mercury grand marquis 4.6 serpentine belt routing?

The 1999 Mercury Grand Marquis has (2) TWO engine styles, both different. The style for Vin numbers with a "W" engine, and the Vin numbers with an "X".The "W" series has the A/C Compressor to the RIGHT of the engine when viewed from the front.The belt circles all components from the outside but t...

Read more

What is the correct routing for a serpentine belt on a 1999 BMW 740 il car?

It is important to have the belts of a car put in the right direction. This serpentine belt goes around the AC compressor, above the AC tensioner,under the crank pulley, around the power steering, over the alternator pulley, under the idle pulley, around the w/p,and behind the tensioner.ÊÊ

Read more

Do you losen the altinator to change serpentine belt on a 94 Jimmy?

You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.

Read more

Resetting trouble codes on a 1998 Plymouth Voyager?

Codes for a 1998 Plymouth Voyager can be reset, by a diagnostic code scanner, or by disconnecting the battery. If the code is still showing up, after work has been done on the vehicle to fix the code problem, the vehicle may need to go into a car dealership to ensure there are not other problems ...

Read more

How do you route smaller serpentine belt on98 zx2 to bypass ac compressor?

The belt that I used my my 1999 ford escort ZX2 is a 6K730 to bypass the A/C. when routing the difference is the belt will come from the power steering to the tension pulley to the crank then water pump and the rest is normal. I hope this helps

Read more

Fuel line routing 94 Camry?

The fuel routing on a 94 Toyota Camry runs from the fuel tank, along the frame, up the front of the engine, and into the fuel rail. The specific routing of the fuel line is important to prevent damage and ensure a steady flow.

Read more

Do you have a Diagram of serpentine belt for 94 ranger 3.0?

check on autozone .com or maybe going to your local store and they might have one or be able to help you with it

Read more

Does a 1987 Plymouth voyager have airbags?

No. Air bags or ABS was not available in the 1987 model year Voyager.

Read more

Belt routing diagram?

look under the hood there is usually a diagram somewhere thereOr ask a new question and include year, make, model, and engine size.

Read more

How many oxygen sensors does a 2000 Plymouth Voyager have?

The 2000 Plymouth Voyager had three engine options for that year, the 2.4L, 3.0L, 3.3L engines. If your vehicle was equipped with the Flex Fuel system or (TLEV) Transitional Low Emission Vehicle, it wouldn't make a difference. The Plymouth Voyager was only equipped with two oxygen sensors, one us...

Read more

Where is the fuel pump for 1997 Plymouth Voyager?

It is in the fuel tank.

Read more

Is a 1989 Plymouth Voyager w auto trans towable?

Not with all four wheels on the ground. The front wheels need to be off the ground.

Read more

Plymouth Voyager transmission will not shift into third?

On my 1990 Voyager, the transmission has a "safe," or "limp" mode. If something is wrong with the trans, it will not shift out of second gear. This is supposedly to allow you to drive to the repair shop at a reduced speed.

Read more

Cost of an oxygen sensor for a 1999 Plymouth Voyager?

Between $40 - $60 seems typical. The actual cost will depend on specifics of your vehicle, such as which engine it has.

Read more

How do you replace a catalytic converter on a 1996 Plymouth Voyager?

The 96 Voyager came with a 4 or 6 cylinder engine, either way you can replace the cat two ways. You can purchase a bolt in replacement or you can purchase a weld in replacement from your local auto parts store. The bolt in assembly is more costly but you can DIY at home if you're handy and have t...

Read more

How do you change the fuel filter on a Dodge 1998 Plymouth Voyager?

It should be located at the rear of the vehicle, attached to the frame rail near the fuel tank, you will have to use fuel connector release tool to free the hoses, but not before you have relieved the pressure on the line. You can then undo the strap holding the filter on and swap out the new one...

Read more

Why does the fan on your 1997 Plymouth voyager only work in low and high speed?

The blower motor speed resistor is burned out. Keep in mind that in many cases the speed resistor burns out because the blower motor is failing and drawing to many amps. So if the new resistor burns out soon, next time replace the blower motor also.

Read more

What does service code P0300 mean on a 1998 Plymouth Grand Voyager?

P0300 = random misfire. Could be as simple as needing a tune up.

Read more

How much would a drive shaft replacement cost on a 1990 Plymouth grand voyager?

The 1990 Grand Voyager was a front wheel drive vehicle, which used a transaxle - there is no driveshaft to replace.Replacing one side halfshaft could range between $300 to $400.

Read more

Ford Aerostar Belt Routing pic?

My 1995 Ford Explorer has a diagram in the front of the engine compartmentshowing how the serpentine belt is routed . Does your Ford Aerostar not havethat .

Read more

What are the car specs of the Plymouth Voyager?

NHTSA front-impact crash-test rating is 4 out of 5. The Plymouth Voyager has three doors and comes with a 4 cylinder engine or a V-6. The engine is in the front and they have front-wheel drive.

Read more

Where are oxygen sensors located 1997 Plymouth voyager?

There are two screwed into the exhaust on the rear of the engine.

Read more

How do you remove serpentine belt on 2005 Chevy Cobalt?

You have to release the stress in the tensioners to remove the serpentine belt. When you put it back on there is a diagram under the hood of the car that takes you step by step.

Read more

What happens if you put a serpentine belt on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

Can a serpentine belt be put on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

What does a code 411 mean on a 1991 Plymouth Voyager?

You should only have a 2-digit code. Here is a link to the entire list: A "41" indicates "charging system excess or no field circuit." Good luck.

Read more

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

How do you replace serpentine belt on a fx 35?

1. Remove front engine undercover.2. Loosen idler pulley (alternator and power steering oil pump belt) lock nut and adjust tension by turning bolt.3. Same is done for the other idlery pulley (A/C compressor belt).

Read more

How do you replace serpentine belt on 2005 Equinox?

Begin by loosening the tensioner pulley on your 2005 Chevrolet Equinox. The serpentine belt will become loose and can be removed. Reverse the process to install your new serpentine belt.

Read more

What happens when the serpentine belt breaks on a car?

when serpentine belt breaks alternator and water pump stop working along with power steering pump

Read more

Can you put a serpentine belt on backwards?

you actually can put a belt on backwards.grooves go to grooves, and smooth goes to smooth.but you have to pay close attention to the belt routing diagram.if the belt is put on the wrong way it can spin the water pump reversed causing an overheat condition very fast after starting.

Read more

Does wd40 damage serpentine belt?

WD-40 doesn't stop rubber squeaks Spraying an oil based lube onto a serpentine or poly-ribbed drive belt may make the squeak disappear for a while, but it doesn't fix the underlying problem.Plus, it damages the belt.Bottom line to nutjobs: WD-40 should NEVER by used on rubber.

Read more

Is the serpentine belt the same as the timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

Is a serpentine belt the same as a timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

What is fan belt routing Jeep Cherokee?

First we will need the model year, what size engine and if it has AC or not.

Read more

What is the serpentine drive belt?

The serpentine drive belt is the rubber belt that is connected to all the pullys 5-6 like the water pump, altenator, a/c clutch, fan, and crankshaft. usually located behind the radiator or on the side of the motor depending on what the motor is and what its in.

Read more

Can I change a serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

Does Jiffy Lube change serpentine belts?

The serpentine belt! For this key component, rely on the Jiffy Lube® serpentine belt replacement to help keep your vehicle on the road.

Read more

What happens when the serpentine belt breaks?

That means when your belt breaks, slips and, ultimately, wears out, everything—from the power steering pump to the alternator and air conditioner—stops working.What's more, the parts it controls can become severely damaged.Broken hoses and belts are bad; a damaged engine is even worse.

Read more

Does serpentine belt affect air conditioner?

Yes, a worn serpentine belt can slip slightly and generate heat due to which AC stops working.The heat generated by the slipping belt over-heats the air conditioner clutch and can cause it to release.

Read more

Can you replace a serpentine belt yourself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

What does a serpentine belt do?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

Can I change my serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

Can I replace serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

Need diagram for 2004 freightliner serpentine belt?

Need an engine make and model to answer this. You either have a Detroit Diesel, Mercedes Benz, Cummins, or Caterpillar engine.

Read more

How often should serpentine belt be changed?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

Does 2002 Camry XL have serpentine belt?

The 2.4 engine has a timing chain. The 3.0 engine has a timing belt, assuming the timing belt is what your asking about.

Read more

Does the serpentine belt affect the transmission?

Effect of Serpentine Belts on Transmission.As a result, if the serpentine belt is worn out or breaks, it results in engine overheating and losing the powered steering and charging system.

Read more

Does serpentine belts slow your car down?

Probably, a little. However, they are required for every other function your car uses, including the generator. So you kinda need it.

Read more

Diagram for changing the serpentine belt?

As you listed no make, model, engine, or year, all I can say is look under the hood for a placard diagram. Usually there is one there.

Read more

How long do BMW serpentine belts last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

Can you drive without serpentine belt?

Since the serpentine belt is generally the only accessory drive belt on vehicles these days, this is what you'll lose: Engine cooling* - The serpentine belt drives the water pump.Without the water pump, there will be insufficient coolant flow to maintain engine temperature, and you will overheat ...

Read more

What causes the serpentine belt to break?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).Squealing sound: Belt slipping.

Read more

How do you change a serpentine belt?

How to Replace a Serpentine Belt Take a good look at both your repair manual and your belt routing diagram under the hood before beginning. Look at the way the old belt wraps around the pulleys. Locate the self-adjusting tensioner and know that you need to be careful when releasing tension ...

Read more

Does Jiffy Lube replace serpentine belts?

The serpentine belt! For this key component, rely on the Jiffy Lube® serpentine belt replacement to help keep your vehicle on the road.

Read more

If I tow a 1999 Plymouth Voyager on a dolly do I have to disconnect the drive shaft?

There isn't a driveshaft to disconnect. That vehicle is a front engine, front wheel drive layout. It uses a transaxle, which combines the transmission and differential into one package. You need to put the front axle on a dolly.If the front wheels are on the dolly, you're good to go.

Read more

When should I replace my serpentine belt?

Under normal conditions, the belt needs to be replaced every 4 to 6 years.However, those living in areas where the temperature and humidity can vary greatly throughout the year may need to change it more frequently.

Read more

Can I drive without a serpentine belt?

As you can see, driving without a serpentine belt is not an option, at least not for very long.*Some cars have an electric water pump and/or electric assist steering.

Read more

How important is a serpentine belt?

Well, it won't keep your pants up, but it does transport power to your vital automotive components.The serpentine belt is one long, snaking, winding belt that keeps your alternator, power steering pump, air conditioning and — in some cases — your water pump running smoothly and effectively.

Read more

How do you set the clock in a 1992 Plymouth Voyager?

Believe it or not, you need to have a casette in the casette player. If you use the casette that cam with the car, it has audible instructions. Now, here's one for you- where is the fuse for the overhead console that protects the compass and drive time features?

Read more

How much does a srap Plymouth grand voyager 8 passenger weigh and worth?

Scrap metal prices change almost daily. Call your local wrecking yard for current prices.

Read more

What it the correct radiator cap for a 1992 Plymouth Voyager 6 cylinder engine?

52079880AA is the OEM part number.16 psi.

Read more

How do you know if you are getting oil pressure in your 2000 3.0 Plymouth voyager?

The low oil pressure light would be on if you had low or no oil pressure. If you question the accuracy of the oil pressure light, a mechanical gauge could be installed permanently or temporarily to double check pressure readings.

Read more

A better diagram of serpentine belt for belt routing than auto zone the belt around water pump is flat side against the pully shouldn't the ridged edge be against the pully instead?

Does the water pump pulley have grooves in it? If so, then the ridges should ride in those grooves. If the pulley is flat, the back side of the belt powers it.Here's a place to get diagrams: http://free-auto-repair-advice.blogspot.com/2007/12/serpentine-and-timing-belt-diagrams.html

Read more

Where could you find an illustration on replacing serpentine belt on '97 Buick Park Avenue?

There should be an illustration in your ownners manual.Just had mine done.. mechanic had to remove psgr side motor mount to release belt. Not a fun job.trust me this ne job you want to pay someone to do, you need to lower the engine cradle to remover the PS motor mount,you could also visithttp://...

Read more

Do you have a diagram of the serpentine route for a 1995 olds royale?

The 1995 Oldsmobile serpentine belt routing diagram can be obtained from most General Motors dealerships. The diagram can be found at most auto-parts stores.

Read more

How do you set the clock in a 1998 Plymouth Voyager?

there is 2 very small black buttons right above where the time is displayed. The one on the left is hour and the one on the right is minute. you have to us something with a small tip to change time like a pen head.

Read more

How do you replace the clutch in a 1994 Plymouth Voyager?

use a flat tip screw driverAnd as you have not detailed the engine I will have to recommend you purchase a service manual or borrow one from your local library.I prefer the Chilton brand manuals

Read more

Why does minivan 1999 Plymouth Voyager goes out of gear while driving?

Could be low on ATF. Check it.

Read more

What is the accessory belt routing for 98 Ford ZX2?

'round the big wheels with grooves... also everyone should have a manual for their vehicle, and the local library should have a SHOP manual available in the reference section--make copies of the right info and read up..you'll be a pro in no time ...good luck:)

Read more

Why cant you detension the serpentine belt tentioner the bolt keeps rotating and not letting you get the belt on?

because the bolt is striped or you pulley is no bad take it off and get another one

Read more

Where is the serpentine belt adjustment bolt on a 1997 Chrysler Town and Country?

The serpentine belt tensioner is spring loaded. There is no adjustment.

Read more

Will a serpentine belt failure damage the engine on the 2001 Rodeo V6?

Not usually but it can be an indication of a problem with one of the driven accessories.A timing belt in many circumstances can indeed do damage if it breaks so replace it at the proper intervals.

Read more

How do you reroute serpentine belt to bypass ac compressor on 1995 town car?

If that model was available without a/c, you will need to purchase the belt for a 95 town car w/out ac, and follow the appropriate belt routing diagram for that model.

Read more

What would cause a serpentine belt to squeal?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).Squealing sound: Belt slipping.

Read more

What happens if your serpentine belt breaks while driving?

A broken serpentine belt leads to a sudden loss of power assist for the steering system, where the steering wheel all-of-a-sudden becomes very hard to turn.A broken serpentine belt stops the water pump from circulating coolant (antifreeze) through the cooling system, and the engine can overheat -...

Read more

Why does my serpentine belt came off when it rains?

This will cause water to flow onto the belt and the resultant belt slip when it rains.Hope thi help.The serpentine belt may come off due to a worn tensioner, idler pulley or pulley alignment.You may need to replace the tensioner, idler pulley, and the serpentine belt to correct the problem.

Read more

What does a bad serpentine belt look like?

The symptoms of a loose serpentine belt include a loud squealing noise when the engine is started or when the steering is turned all the way to one side.A serpentine belt that keeps slipping off the pulley is another symptom of a bad tensioner.

Read more

Can you drive with a bad serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

What causes a serpentine belt to slip off?

Slipping can be the result of a loss of belt tension (or a weak automatic tensioner) or pulley misalignment.When the belt slips off the track, the friction between the belt and accessory drive pulleys causes the belt to overheat.If you hear a high pitched squealing noise, it's probably time for a...

Read more

What are signs of a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

Can you drive a car with a broken serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

How much does it cost to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

What causes a serpentine belt to come off?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).

Read more

How do you change the serpentine belt on a 1994 mercury cougar xr7?

with a 1/2" rachet or breaker bar placed in the square whole on the tensioner pully, you push (from passenger side to drivers) which will release the presure on the belt. Might want to draw a "map" of how the belt goes cause it ain't obvious when its off the car.

Read more

How do you change a serpentine belt on a Chevy Silverado?

Shop Products Familiarize yourself with the belt routing diagram.Insert a 3/8 inch drive ratchet into the belt tensioner.Pull the tensioner counterclockwise to loosen the belt.Pull the belt off the idler pulley.Release the tensioner.Pull the belt off and out.

Read more

How long does it take to replace serpentine belt?

How Long Does It take To Replace A Serpentine Belt? For professional automotive technicians with the right tools and training the replacement of a serpentine belt usually takes about 30 min to an hour.This time varies by the make, model, and year of vehicle that you're driving as some take longer...

Read more

Do I need to replace my serpentine belt?

Most serpentine belts generally last between 50,000 and 100,000 miles.Eventually, your car's serpentine belt will wear down from continuous exposure to heat and friction and will need to be replaced.

Read more

What is the purpose of a serpentine belt?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

What happens if a serpentine belt breaks while driving?

A broken serpentine belt leads to a sudden loss of power assist for the steering system, where the steering wheel all-of-a-sudden becomes very hard to turn.A broken serpentine belt stops the water pump from circulating coolant (antifreeze) through the cooling system, and the engine can overheat -...

Read more

Why does my serpentine belt keep coming off?

Diagnosing Serpentine Belt Problems.Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).

Read more

What are the signs of a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

How long can a car drive without a serpentine belt?

Not very long if it powers the water pump, -possibly 5-7 minutes before you overheat.

Read more

How can you bypass a serpentine belt on a 2002 converible sebring from the ac compressor?

You realy can't. If your intention is not to power the A/C unplug the wire that connects to the electric clutch. It should be right behind the pully.

Read more

Do you have a diagram of how to put the serpentine belt on the pulley?

You may get an answer if you list the vehicle & engine you are talking about. You are not going to get an answer to this question as is.

Read more

How do you replace a serpentine belt on a 1995 Chevrolet Camero?

Replacing the serpentine belt on both V6 & V8 rear drive engine are fairly easy than front wheel drive. The belt is located just between the front of the engine and the radiator. You have plenty of clearance to work. Just need to losen the tension and the belt should come out. Putting the new...

Read more

How do you repair the serpentine belt on a 1998 Mitsubishi Galant?

You don't repair a serpentine belt. You replace the worn or broken belt with a new one.

Read more

Where is the tensioner pulley to tighten the serpentine belt on a 2000 Chevy Silverado?

If you're standing at the front of the truck and looking into the engine compartment the tension pulley is on the left side about half way down.

Read more

How do you install serpentine belt on 88 Chevy silverado 4x4 350 auto?

Loosen tensioner and follow label (under hood) for routing

Read more

How often is the serpentine belt on the 2002 Lexus gs300 changed?

Only as needed. The serpentine belts hold up well unless there is a problem with the belt tensioner or any of the driven accessories.

Read more