Is it easy to change rear trans bearing?

Cars & Vehicles

i doent know why doent you tell me

Previous questionHow do you turn off the low coolant beeping on the 2001 Laredo?
Next questionHow do you change out a cv axle on a 1998 eclipse?

Related question

Is it easy to change brake fluid?

If you want to change the brake fluid yourself, follow these steps: Remove the old, dirty fluid from the master cylinder reservoir.Use a lint-free cloth to wipe out the reservoir.Pour new brake fluid into the reservoir just until it reaches the “Full” line, replace the cap on the reservoir.

Read more

Is it easy to change a serpentine belt?

And to make matters worse, there were often two or three belts to change.Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and insta...

Read more

Is it hard to change rod bearings in Chevy 4.3?

If you don't have the tools and/or know-how, it could be very difficult.

Read more

Where is the starter on 91 Pontiac sunbird 2.0L and is it easy to change?

You can find the starter at the lower front part of the engine. You can change starter easily any time it has a fault.

Read more

Is it easy to drive in NZ?

There is only one route which connects one town to another, so navigating and driving in New Zealand is not difficult.There also aren't that many cars on the road, so you can drive at your own comfortable speed.

Read more

Is it easy to drive in Majorca?

Driving in Majorca is by far the best way to travel the island.Car hire agencies are easy to find and car hire rates are by no means very expensive.Renting a car will allow you the freedom to witness the beauty of the island at your leisure.

Read more

Is it easy to replace fuel pump?

Fuel pump replacement is very important.If the engine does not have a functioning fuel pump, it will immediately “starve” and stop functioning.When fuel pumps are not replaced properly, the whole system is damaged.Although it might sound difficult, fuel pump replacement is easy.

Read more

What is a muffler bearing is it expensive or difficult to change?

This has been around for as long as I can remember. There is no such thing as A muffler bearing. Somebody is pulling your leg. 100% correct. Just for fun, tell whoever told you needed to change it that you need to borrow a spagnasty because you figure you'll change the blinker fluid at the same t...

Read more

Is it easy to drive in Malta?

Driving in Malta, especially if you're new to the islands, can be daunting.Malta presents a far easier driving experience than those.All the more so if you come from a nation with right-hand drive vehicles.So, don't be put off.

Read more

Is it easy to drive in Czech?

Driving in the Czech Republic.With the driving licence in your wallet, ZERO blood alcohol concentration (as stated by law), seatbelt fastened and headlights on, you're 100% ready to drive! The speed limit in urban areas is 50 km/h, while outside town you can drive up to 90 km/h.

Read more

Is it easy to drive in Hawaii?

Driving in Hawaii is relatively straightforward as roads are well signed and in good condition, particularly on the island of Oahu.Driving in Hawaii can be done by tourists as long as you have a valid International driver's license or a foreign driver's license written in English.

Read more

Is it easy to drive in Paris?

Driving in Paris, France.Like many major European cities, Paris harbors an excellent public transportation system.In Paris, you can get around quite easily without ever taking the driver's seat.

Read more

Is it easy to replace air filter?

You may not be ready to tackle car maintenance jobs like changing the oil or replacing spark plugs, but changing your vehicle's engine air filter is an easy job that you can do.It is a good idea to check the air filter at each oil change.You should change your engine air filter annually or every ...

Read more

Is it easy to drive in Oahu?

One of the best drives on Oahu is a relatively easy drive to Windward Oahu, the eastern shore of the island.If you didn't stop in Kailua and Lanikai as mentioned in the prior drive, be sure to stop there on your return trip to Waikiki after your visit to Kualoa Ranch.

Read more

Is it easy to drive in Lanzarote?

Yes, it's easy to drive in Lanzarote.Just be careful about driving in Arrecife - narrow roads and busy in places.The drive from the airport to Playa Blanca is easy once you get out of the airport and onto the main road.It is a direct road with little traffic.

Read more

Is it easy to drive in Romania?

Unfortunately, Roving around Romanian equal poor road conditions.Therefore, whether as a driver or as a pedestrian: Beware! The World Economic Forum ranks Romania 126 out of 134 states for road quality with limited freeways and infrequent passing lanes.

Read more

Is it easy to drive in Mexico?

Just like there are parts of the US that you might avoid driving in at night when you're alone, there are places in Mexico that you will want to avoid driving at night when you're alone.Driving in Mexico, in general, is perfectly safe and like I mentioned above, is one of the best ways to see the...

Read more

How long does it take to change rear shocks?

How long does it take to replace rear shocks? It will take about 30 minutes if you're learning as you go.If you know what you're doing, it will probably take about 20 minutes.

Read more

How do you change rear brake pads on a 1995 Firebird Trans Am?

Lift the car, remove the tire, remove the brake shoe/caliper and remove the old brake pad. Put in the new brake pad, replace the brake shoe/caliper, replace the tire, and lower the car.

Read more

How long does it take to change rear main seal?

How long does it take to change engine rear main seal.Depending on extent of rust/age conditions , anywhere from 3-7 hours , maybe more if broken bolts along the way.Depending on extent of rust/age conditions , anywhere from 3-7 hours , maybe more if broken bolts along the way.

Read more

Is it possible to put the wheel hub on wrong after changing the bearings?

The year, make and model, front hub, rear hub, more info would help.

Read more

Is it possible to change an auto trans 98 corolla to a manual If so what parts do you need?

Yes it is possible to do a transmission swap on almost any car. You will most likely need a transmission jack and engine hoists as part of the job. In addition, you will need to buy a manual transmission kit which should come with all the parts needed to make the transmission awap including shift...

Read more

Can you change from auto trans to standard trans on 1989 mercury tracer?

It's doable, but not really feasible. Especially for a car as old as that and which doesn't have any particular collector's value. You'd be sinking a lot more money into it than it's worth.

Read more

01 Intrepid right side trans output bearing can it be replaced in vehicle?

no u have to pull it out and go inside to fix it i am a mechanic for coles auto! i hope this help u

Read more

How easy it is to donate a car to charity?

It depends what you want to do with the vehicle. There is a site Kars 4 Kids that is a very easy process. There are also no taxes to do this. The DMV will also take them off your hands if you wanted to do that.

Read more

Is it easy to be a car salesman to anyone?

No it isn't, you have to be very smart and a liar and I know someone who is very successful as one but it is not a very good occupation choice so go to college or own one of your own car dealerships.It isn't very good to lie so....Signed,Goshir York

Read more

Why have you got rear wheel knocking noise after bearings changed?

It could be several things, your bearings could be under a pre load, which means there is exesive pressure on them caused by them being over tightend, it could also be as simple as a brake hanging up on the drum or disk. you may have a bent rim possibly but that would cause the car to vibrate. Al...

Read more

How difficult is it to remove the rear differential and renew any worn bearings on a 2001 Toyota Powervan?

Not bad. Some specialty tools needed like a foot lb torque wrench, an inch lb torque wrench and a dial indicator. A shop manual for that vehicle would also be helpful.

Read more

How easy is it to fix a transit accelerator?

easy and hard all you have to do is pull out what is known as the servo then pop the other servo in and your done.

Read more

Is it easy to steal a car grill?

depends on vehicle models and brand,some grilles are screwed from inside ,some uses plastic clip locks.some moulded to the bumper and with additional small screw,some may require to remove the wrap around bumper just to get to the grille.

Read more

How easy is it to recharge your car?

ya you just plug it in :)

Read more

Do rear wheels have bearings?

Auto Repair For Dummies, 2nd Edition Wheel bearings usually come in pairs of inner and outer bearings.Usually, only the non-drive wheels (that is, the front wheels on rear-wheel drive vehicles and the rear wheels on front-wheel drive vehicles) have repackable wheel bearings.

Read more

Is it easy to rust proof a car yourself?

Rust proofing your car is easy with the right products.Today's vehicles are manufactured with good corrosion protection … rust problems have almost vanished in modern vehicles," Consumer Reports says its annual auto surveys show. "Standard rust-through warranties for most domestic and imported ve...

Read more

Is it easy to get RAV4 accessories in Saudi Arabia?

Yes, you can get the RAV4 accessories in Saudi Arabia easily. Infact you can place an order for them online on the company website and a sales representatives will contact you shortly.

Read more

Is it easy to become a freelance courier?

It doesn't appear to be too difficult, if you know the business. The trick is getting the customers, and getting paid.There are several different types of courier, as well. Bicycle couriers, drivers, legal courier, small or large truck same day delivery- you should be able to think of others, as ...

Read more

How easy is it to refinance a car loan?

Refinancing a car loan involves taking on a new loan to pay off the balance of your existing car loan.People generally refinance their auto loans to save money, as refinancing could score you a lower interest rate.As a result, it could decrease your monthly payments and free up cash for other fin...

Read more

Is it easy to hire a car in Dublin?

Car hiring should not be a problem in Dublin. It being in Europe, there should be many car rental companies that allow you to rent. Also many of the rental companies in US has there branches in Dublin.

Read more

How easy it is to insure a car?

Depending on the model, year, brand and estimated value of the car can make insurance easy to get. Expensive brands and expensive cars will be more money to insure. To insure a vehicle one could go to a local insurance company and price out bundles and make adjustments. Also, one could go to a lo...

Read more

How do you check rear axle bearings?

Read more

Need to change wheel bearings on 2004 awd GMC Safari?

First, lift up the front and take off the wheels with a tire iron. Next, unbolt the brake caliper using the 3/8-inch ratchet and socket, pull it off the spindle and hang the caliper by the upper control arm. Then, remove the dust cap using a hammer and flathead screwdriver and remove cotter pin i...

Read more

Cost of rear end differential bearings?

Rear end differentials have several different types and sizes of bearings. The cost to replace all of the bearings will be around $400.

Read more

Why does my rear driver-side tire make a rattling noise when going over a bump or rough roads could it be worn out bearings and is that an easy fix?

Assuming something isn't broke it is more likely the strut that is worn out. Bearing would grind all the time. When the strut is worn out and you go over a bump the tire will leave the ground which lets it vibrate and make noise.

Read more

How expensive is it to replace a wheel bearing?

Wheel Bearing Replacement Cost Estimates The average cost for a Wheel Bearing Replacement is between $445 and $579 but can vary from car to car.

Read more

Is it dangerous to drive with loose wheel bearings?

The wheel bearings in your vehicle work with the tire, hub, and wheel to make a smooth ride while you are driving down the road.It is not safe to drive with a missing wheel bearing.Driving without a wheel bearing is dangerous, so if you experience any of the 3 signs below, contact a mechanic as s...

Read more

When Changed brakes bearings rear end seals on 2004 GMC 2500 HD duramax and still grinding on right side?

The carrier bearings or pinion bearings may be at fault.

Read more

Is it bad to drive with a worn wheel bearing?

Well, it ain't clever, that's for sure.Thing is once its started to go it's very hard to say how long it'll last.And if it seizes, it can lock the wheel up, or maybe even make the wheel come off, which is a ride-stopping, wallet-emptying kind of event.

Read more

Is it dangerous to drive with a bad wheel bearing?

It is not safe to drive with a missing wheel bearing.One of your wheel bearings may be about to fall off, and the symptoms themselves pose dangerous to driving.Loud Noise Coming from the Tire or Wheel The most common symptom with a bad wheel bearing is a loud noise coming from the tire or wheel o...

Read more

Is it safe to drive with a bad wheel bearing?

Not knowing how bad the bearing is, I can't say how long it will last before the wheel falls off. Drive to your local garage for repair and don't take the highway.

Read more

Is it OK to use wd40 on skateboard bearings?

It's important to use a silicone-based lubricant.WD40 or others like it will dry out your bearings and attract dust and dirt.It doesn't take much, and the excess will just spin out when you replace your shields, pop your bearings back in your wheels and start shredding.Skate safe and enjoy your n...

Read more

What type of tool is needed to change an air conditioning Compressor bearing?

You are better off replacing entire compressor, then you know all other bearings and parts are good.

Read more

What is the cost to change front wheel bearing on a 2002 ford explorer 4wd?

$45 in parts + $150 in labor

Read more

Is it ok to use non trans fat waste oil to produce biodiesel?

Yes you can use all trans fat oils to make biodiesel

Read more

How are the outer axle bearings of a rear-wheel drive solid rear axle lubricated?

In many cases they are lubricated from the gear oil in the differential.

Read more

Why is my ABS light on after changing wheel bearing?

But once you start driving, you get another ABS light on after wheel bearing replaced.Or, it determines that the weak signal indicates a bad sensor, so it lights up the ABS light.You can try removing the sensor from the old wheel bearing hub and cleaning off the rust.

Read more

Renault Megane the coil spring is broken is it easy to replace?

The coil springs are not easy to remove or install. The spring needs to be compressed in order to be removed. It takes several hundred pounds of pressure to compress the spring.

Read more

Where is the timing belt on 2001 Cherokee sport and how easy is it to replace?

The timing belt is not a belt on a Cherokee sport. It's a chain. It's located under a housing on the crank shaft. In order to replace it you will need to remove the alternator, the water pump, the a/c compressor, the radiator and the engine fans. An experienced mechanic can get it done in about 3...

Read more

How do I change a wheel bearing?

Steps Park your vehicle on a flat surface. Use wheel chocks to secure wheels whose bearings you aren't replacing. Loosen the lug nuts and lift the wheel using a jack. Unscrew the lug nuts and remove the wheel. Remove the brake caliper. Remove the dust cover, cotter pin, and castle nut. ...

Read more

Can a rear end accident cause the front wheel bearing to go bad?

no.not if its a car accident

Read more

How to Change drive shaft between motor and rear end?

1 put car in neutrol 2 put e brake on 3 drain transmission fluid 4 unbolt drive shaft from rear end pull shaft out or if your car is newer 2005 have a shop take care of it

Read more

Can you change front wheel car to rear wheel?

With fabrication and lots of $$$ anything is possible.

Read more

How do you replace rear wheel bearing 1997 Town Country?

Remove the tire and wheel. Remove the axle end. Remove the axle seal. Remove the wheel bearing. Reverse the process to install the new wheel bearing.

Read more

Is diesel easy to set on fire?

No, diesel fuel is not easy to set on fire. It has to have a good wick, or be vaporized to be quickly set on fire. You can put out a match in a pool of diesel fuel, but you wouldn't want to drop a match into a tank that holds it, as enough may have evaporated to cause it to ignite. It is not as v...

Read more

Is a ball joint easy to fix?

you dont fix them you replace them difficulty doing so varies with car make and model

Read more

Is Boston easy to walk around?

It is easy to get around Boston without a car; in fact, "the Walking City," is one of Boston's nicknames.From the western end of Newbury Street, Boston's primary shopping and restaurant area, to the Boston gardens is only a one-mile walk.

Read more

Is easy to drive in Spain?

Driving in Spain.While it's relatively easy to catch a train or bus to almost anywhere in the country, some places in Spain are only accessible by car or on foot.

Read more

How do you change a bearing?

Steps Park your vehicle on a flat surface. Use wheel chocks to secure wheels whose bearings you aren't replacing. Loosen the lug nuts and lift the wheel using a jack. Unscrew the lug nuts and remove the wheel. Remove the brake caliper. Remove the dust cover, cotter pin, and castle nut. ...

Read more

How do you change a rod bearing?

How to Replace Rod Bearings Remove the connecting rods from the pistons and crankshaft, if they are not already out. Remove the old bearings. Clean the bearing surface of the rods on either end with a lint free rag. Slide one bearing into the end of the rod's big end and one bearing into t...

Read more

Will tight carrier bearings lock the rear wheels?

well if hVE C-10 fighter jet your ac-70 might lock up and couse you do skid on the runway, the best fix for this is to put some moon wax on it and then have some coffee

Read more

What steps do you take to change trans fifter on my 97 neon?

There is very little clearance space underneath a Dodge Neon. I'd suggest you take it to the nearest Lee Miles or other transmission place and ask for their auto transmission filter and fluid replacement package. Believe me, its worth every penny.

Read more

How do you change your wheel bearing?

Vehicle type and year is essential for proper answer.

Read more

How often do you change skateboard bearings?

How often should you replace your bearings? If you use high quality bearings, you should replace them once a year or two.

Read more

Is Copenhagen easy to walk around?

Copenhagen is an extremely easy city to get to know by foot, because it is small.After a day walking around it becomes familiar.It is also very easy because all the main attractions aren't too far from each other.The sidewalks are not even though, so bring comfortable shoes.

Read more

If you have your cdl license, is it easy to find truck driving jobs?

Now in day is not that easy to find a truck driving job, even wiht the cdl license, unless you got your own truck and willing to work for less than the average workers.

Read more

Do people like truck driving, and is it easy to get employed?

In order to be a truck driver you would first have to achieve the proper license to drive a truck and that would involve the proper training. It is a fairly good paying job but might be difficult if you are doing long hauls and have a family at home. In the US, the average salary for a truck driv...

Read more

1998 Mazda millenia p0733p0734 gear ratios how easy is it to fix?

Start by checking the transmission fluid level. If this is good then replace the transmission fluid and filter. If it continues it needs transmission work.

Read more

Can you replace a 390 engine 289 without having to change trans?

No, the 390 uses a C6 transmission and the 289 uses a smaller C4.

Read more

Is it hard to change engine mounts?

Generally, they are not easy to access, and you need to support the engine to replace one, so most of the mechanic's motor mount cost is paying for labor.If the vehicle has three motor mounts and they are hard to get at, like in a minivan, labor costs are higher.

Read more

Is it legal to change the odometer?

While each state has its own individual statute, federal law prohibits disconnecting, resetting, or altering of a vehicle's odometer with intent to change the number of miles indicated.If the odometer mileage is incorrect, the law requires a statement to that effect to be furnished on the title t...

Read more

Is it necessary to change transmission filter?

Most automobile manufacturers recommend a transmission filter change every 2 years, or every 30,000 miles (whichever comes first).When your mechanic replaces the filter, he or she should also change the fluid, and replace the transmission pan gasket.

Read more

Is it necessary to change differential fluid?

How often do I need to replace the differential fluid? Most manufacturers recommend that the differential fluid be changed every 30,000 to 60,000 miles.It is a messy job, and should be done by a licensed mechanic.

Read more

Is it necessary to change timing belt?

Unfortunately, in most cases, there are no obvious signs the timing belt is near death; it will just break.That's why highly rated auto mechanics recommend replacing it every 60,000 to 100,000 miles.

Read more

What is a wheel bearing Is it dangerous when it goes out Is it expensive to repair?

A wheel bearing is a thing that sits between a stationary part of a car (like an axle) and a rotating part of a car(like a wheel), allowing these to move easily WRT each other.It CAN be dangerous when they go out, as that can cause the wheel to lock up, or even to come off.Either of which are lik...

Read more

Is it still safe to drive your car if the hub bearing needs to be replaced?

Not really - if it really gets bad it could cause you to lose control of cehicle or even heat up enough other components to cause heat damage & make it even more expensive

Read more

Is it bad to change transmission fluid?

Don't do it unless your transmission is running fine and the fluid is first-rate, because it can make transmission failure imminent.Some shops will not change the automatic transmission fluid on high-mileage cars due to the risk of problems arising after the service.

Read more

How much does it cost to replace a carrier bearing?

The average cost for a carrier bearing replacement is between $269 and $361.Labor costs are estimated between $132 and $168 while parts are priced between $137 and $193.

Read more

How long does it take to replace a wheel bearing?

Rear wheel drive, tapered roller bearing: about 15-45 minutes; wear gloves or spend another 10 minutes washing grease off your hands.Front wheel drive with pressed on bearing: 30–120 minutes depending on whether it can be pulled off and pressed in with a specialty tool.

Read more

How long does it take to fix a wheel bearing?

Rear wheel drive, tapered roller bearing: about 15-45 minutes; wear gloves or spend another 10 minutes washing grease off your hands.Front wheel drive with pressed on bearing: 30–120 minutes depending on whether it can be pulled off and pressed in with a specialty tool.

Read more

How much does it cost to replace Porsche IMS bearing?

For a 2000-2005 model, it costs about $2500 to install a ceramic bearing IMS replacement versus the approx.$20,000 cost of replacing an engine.Say we have a 1 in 10 failure rate, that works out to $2000 per car (on average).

Read more

How much does it cost to fix a wheel bearing?

The average cost for a wheel bearing replacement is between $642 and $705.Labor costs are estimated between $176 and $223 while parts are priced between $466 and $482.Estimate does not include taxes and fees.

Read more

How much does it cost to replace a wheel bearing?

You will pay about $400, on average, for front wheel bearing replacement.The labor will be anywhere from $140-$180, while parts may cost as little as $200 or as much as $400.The difference in prices is due to the cost of parts for more expensive cars as well as the various fees that individual me...

Read more

What is the torque setting for the rear wheel bearing nut on a suzuki swift?

just put it on finger tight, if it breaks down then get a real car.

Read more

How is the rear wheel bearing lubricated on a 2007 Nissan civilian bus?

wd40, from experience, sounds stupid but it works!

Read more

1994 Mark VIII you have antifreeze leaking from the rear of the engine you are not able to see where it is coming from it is not from trans cooling lines appears coming from above no water in oil?

there is a tube that runs from the back of the heads across each other

Read more

Do you have to pull to pull the motor to change rear crank seal 1994saturn sc?

yes. because it is front wheel drive, you also have to remove the transmission

Read more

Is it better to go to dealer for oil change?

Generally speaking, though, it shouldn't matter much where you get your oil changed.As long as you keep your receipts and perform oil changes at recommended intervals, you won't void your warranty if you go to an independent shop -- and you might save some time and a little money.

Read more

How much should it cost to fix a wheel bearing?

Know what price you should pay to get your vehicle fixed.The average cost for a wheel bearing replacement is between $642 and $705.Labor costs are estimated between $176 and $223 while parts are priced between $466 and $482.Estimate does not include taxes and fees.

Read more

How much does it cost to replace a throwout bearing?

The parts cost of a throw out bearing will vary depending on if the bearing is serviced separately or together with the slave cylinder.The cost for the bearing on Amazon ranges from $15.00 to $45.00 (US).A bearing and slave cylinder combo will run about $160.00 (US).

Read more

Your 1.0 metro runs great but only getting 25 mpg It doesn't smoke starts easy every morning changed air filter and oxygen sensor still no change?

have you tried new plugs you should get double that mpg

Read more

How many hours to change front wheel bearing on 2001 venture van?

I you are a good mechanic, and have all the right tools, about 3 hours.

Read more

Want to change from 454 to 350 is it possable?

big block to small block. you change the engine mounts position and possibly the trans. but yes.

Read more