How often is the serpentine belt on the 2002 Lexus gs300 changed?

Cars & Vehicles
Serpentine Belts

Only as needed. The serpentine belts hold up well unless there is a problem with the belt tensioner or any of the driven accessories.

Previous questionWhat is drift in automotive?
Next questionWhere is the fuel cut off switch located in a Pontiac Montana and how do you reset it?

Related question

How often should serpentine belt be changed?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

How do you change front brake rotor Lexus gs 300?

to replace front rotors first remove two bolts that hold on the caliper. use a piece of wire to tie it to the upper strut do NOT let it hang! then remove two bolts that hold on the caliper tray i think they are 17 mm you will need a breaker bar to do this. then take off the rotor sometimes they a...

Read more

Reset a navigation system on Lexus gs300?

I am not able to turn on the volume on gps in my lexus gs300 navigation

Read more

How do you change the serpentine belt on a 2002 Chrysler town and country mini-van 3.8 engine?

There should be an idler pulley that you need to loosen to take belt off, draw a diagram of how the belt looks before you take it off so you can see how it goes back on.

Read more

How often does a serpentine belt need to be replaced?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

How do you change a serpentine belt?

How to Replace a Serpentine Belt Take a good look at both your repair manual and your belt routing diagram under the hood before beginning. Look at the way the old belt wraps around the pulleys. Locate the self-adjusting tensioner and know that you need to be careful when releasing tension ...

Read more

Does 2002 Camry XL have serpentine belt?

The 2.4 engine has a timing chain. The 3.0 engine has a timing belt, assuming the timing belt is what your asking about.

Read more

How can you bypass a serpentine belt on a 2002 converible sebring from the ac compressor?

You realy can't. If your intention is not to power the A/C unplug the wire that connects to the electric clutch. It should be right behind the pully.

Read more

Diagram for changing the serpentine belt?

As you listed no make, model, engine, or year, all I can say is look under the hood for a placard diagram. Usually there is one there.

Read more

What is the new car price for the Lexus GS300?

According to the Kelly Blue Book, the 2013 Lexus GS300 series has a MSRP of $48,125. This is for the car with the standard included features. Other features options will change the price.

Read more

Does the Lexus gs300 have a 2jz?

The IS300 uses the same 2JZ-GE 3.0-liter DOHC 24-valve straight-six that propels the bigger Lexus GS300 sedan, an engine that traces its lineage to the old Toyota Supra.Lexus does plan to make a manual transmission available in about a year.

Read more

What is the firing order for Lexus gs300?

Fig. 3: 3.0L (2JZ-GE) Engine Engine Firing Order: 1-5-3-6-2-4 Distributor Rotation: Clockwise

Read more

Can I change a serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

Does Jiffy Lube change serpentine belts?

The serpentine belt! For this key component, rely on the Jiffy Lube® serpentine belt replacement to help keep your vehicle on the road.

Read more

How do you change the serpentine belt on a 1994 mercury cougar xr7?

with a 1/2" rachet or breaker bar placed in the square whole on the tensioner pully, you push (from passenger side to drivers) which will release the presure on the belt. Might want to draw a "map" of how the belt goes cause it ain't obvious when its off the car.

Read more

Can I change my serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How often do you need to change the timing belt?

some vehicles the interval is every 60 thousand miles while other it is now 100 thousand miles

Read more

Is it easy to change a serpentine belt?

And to make matters worse, there were often two or three belts to change.Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and insta...

Read more

What's the difference between Lexus GS 300 and 350?

The GS 350 and the GS 300 are the same car, so they come with the same features and options; the only difference lies in the powertrain.The GS 350 features a more powerful V6 engine and is available with all-wheel drive.The GS 300, on the other hand, is more efficient and only available in rear-w...

Read more

How do you change a serpentine belt on a 2001 Chevy Suburban?

Read more

How do you change a serpentine belt on a Chevy Silverado?

Shop Products Familiarize yourself with the belt routing diagram.Insert a 3/8 inch drive ratchet into the belt tensioner.Pull the tensioner counterclockwise to loosen the belt.Pull the belt off the idler pulley.Release the tensioner.Pull the belt off and out.

Read more

How do you change a serpentine belt on a 2001 Chrysler Town and Country?

How to Replace the Serpentine Belt in a Chrysler Town & Country Open the hood and find the belt tensioner pulley. Look at how the belt is routed around various pulleys. Use a wrench to rotate the belt tensioner pulley bolt and slide the old belt off of the tensioner pulley. Make sure y...

Read more

How do you change a serpentine belt on a 2008 Toyota Corolla?

Read more

How do you change a serpentine belt on a Mazda 3?

How to Replace a Mazda 3 Serpentine Belt Open the Mazda 3's hood and support it with the prop rod. Connect the belt-tensioner tool into serpentine belt tensioner and move the tensioner pulley away from the belt with the tool. Pull the belt off the engine accessory pulleys by hand. Stretch ...

Read more

How often do you change the timing belt on a Vauxhall Astra?

Timing chain recommended changes is 10years or 100,000 miles but most do it around 70,000.A timing belt won't rattle, but does need doing early usally about 40,000-60,000 or 6 years but I'm not sure for that exact car again its wise to do early.

Read more

Do you losen the altinator to change serpentine belt on a 94 Jimmy?

You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.

Read more

Is the serpentine belt the same as the timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

How to figure out when to change the serpentine belt in 2001 Toyota corolla car?

If you look at the surface of the belt on the smooth side there will be fine cracks in the surface. Very bad ones will have missing pieces in the ridges. ===ANOTHER ANSWER=== ANOTHER WAY to tell is by the mileage. If you have 60,000 miles or more, I would chage it or have it changed. It is well w...

Read more

How important is a serpentine belt?

Well, it won't keep your pants up, but it does transport power to your vital automotive components.The serpentine belt is one long, snaking, winding belt that keeps your alternator, power steering pump, air conditioning and — in some cases — your water pump running smoothly and effectively.

Read more

How do figure out when to change the serpentine belt in 2001 Toyota corolla car?

Look at the belt. If it's shows signs of being frayed on the edges, or if it looks dry and cracked by the inner ribs, or if you hear a squeeling sound when you accelerate, or if you have more than a 1/4 inch play (push your finger on the belt), it's time to change your belt.

Read more

Is a serpentine belt the same as a timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

What is the serpentine drive belt?

The serpentine drive belt is the rubber belt that is connected to all the pullys 5-6 like the water pump, altenator, a/c clutch, fan, and crankshaft. usually located behind the radiator or on the side of the motor depending on what the motor is and what its in.

Read more

How do you remove serpentine belt on 2005 Chevy Cobalt?

You have to release the stress in the tensioners to remove the serpentine belt. When you put it back on there is a diagram under the hood of the car that takes you step by step.

Read more

Where is the oil control valve in a 1998 Lexus gs300?

s.b. at the top of the cam cover, will have an elec. lead to it.

Read more

How many pounds of Freon does it take for a 2001 Lexus GS 300?

There should be a sticker in the engine compartment with the AC refrigerant and oil quantity information.

Read more

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

How do you replace serpentine belt on a fx 35?

1. Remove front engine undercover.2. Loosen idler pulley (alternator and power steering oil pump belt) lock nut and adjust tension by turning bolt.3. Same is done for the other idlery pulley (A/C compressor belt).

Read more

How do you replace serpentine belt on 2005 Equinox?

Begin by loosening the tensioner pulley on your 2005 Chevrolet Equinox. The serpentine belt will become loose and can be removed. Reverse the process to install your new serpentine belt.

Read more

How often should you check the belts on any car?

You should check belts, hoses, fluids, wiper blades, lighting, tires and tire pressure at least every oil change.Once every 3 months or 3000 miles. Which ever comes first.

Read more

When do you change the cam belt on a 2002 Toyota rav4?

You should change the belt when it is about to wear out, which a mechanic should be able to tell you when you need to, or you can also change it more often to make sure you wont need to.

Read more

What happens when the serpentine belt breaks on a car?

when serpentine belt breaks alternator and water pump stop working along with power steering pump

Read more

How often do i need to change the timing belt in my 2006 Subaru impreza?

Subaru says 105,000 miles. Far be it for me to contradict the engineers, that sounds like a lot, it's the most I have ever heard of. And it IS an interference engine. If it breaks, the valves will collide with pistons= blown engine

Read more

How long do BMW serpentine belts last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

Does the serpentine belt affect the transmission?

Effect of Serpentine Belts on Transmission.As a result, if the serpentine belt is worn out or breaks, it results in engine overheating and losing the powered steering and charging system.

Read more

Do you have a diagram of how to put the serpentine belt on the pulley?

You may get an answer if you list the vehicle & engine you are talking about. You are not going to get an answer to this question as is.

Read more

What happens when the serpentine belt breaks?

That means when your belt breaks, slips and, ultimately, wears out, everything—from the power steering pump to the alternator and air conditioner—stops working.What's more, the parts it controls can become severely damaged.Broken hoses and belts are bad; a damaged engine is even worse.

Read more

How much does it cost to replace the serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How expensive is it to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

Where is the tensioner pulley to tighten the serpentine belt on a 2000 Chevy Silverado?

If you're standing at the front of the truck and looking into the engine compartment the tension pulley is on the left side about half way down.

Read more

What is the purpose of a serpentine belt?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

What causes the serpentine belt to break?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).Squealing sound: Belt slipping.

Read more

How do you repair the serpentine belt on a 1998 Mitsubishi Galant?

You don't repair a serpentine belt. You replace the worn or broken belt with a new one.

Read more

How do you replace the serpentine belt on a 1993 Mercury Cougar?

To remove the serpenteen belt on this vehicle, you must first locate the spring loaded tensioner. You will need a 1/2" breaker bar or a socket to recoil the spring load. doing this will release the tension on the belt. You can then remove the belt.NOTE: If you are just changing the belt with a ne...

Read more

Where is the serpentine belt adjustment bolt on a 1997 Chrysler Town and Country?

The serpentine belt tensioner is spring loaded. There is no adjustment.

Read more

How do you tighten the serpentine belt on a 1997 Saturn?

You don't. The belt tension is automatically adjusted via a spring loaded tensioner. If the serpentine belt is noisy or worn out prematurely. replace the tensioner. The belt should be inspected for cracks and other signs of wear. Replace worn out belt(s) before they break leaving you stranded.

Read more

What happens if you put a serpentine belt on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

What is the cost to replace serpentine belt?

It is very inexpensive to replace a serpentine belt.The replacement cost is only going to be between $90 and $200 in most cases.The belt itself will cost between $25 and $75 while the labor costs will probably be between $75 and $120.

Read more

What size belt is needed to bypass the ac compressor on 1993 Lexus ls400?

it would be a 5 by 6 belt for a magnum for a Lexus you would need a 3 by 7

Read more

Belt changing belt on trailblazer?

You can change the serpentine belt on your Chevrolet trailblazer, by loosening the tensioner pulley. With the loosened tensioner pulley the belt will come off easily. Tighten the new belt with the tensioner pulley.

Read more

How do you get the accessory drive belt or serpentine belt off of a 1989 sunbird?

To remove the accessory drive belt or the serpentine belt from the motor on a 1989 Sunbird, it is necessary to loosen the belt tensioner. Look for a pulley that has a bolt in a slot. Loosen the bolt and move the tensioner so there is a gap in the belt. Then remove the belt from each pulley.

Read more

What is the correct routing for a serpentine belt on a 1999 BMW 740 il car?

It is important to have the belts of a car put in the right direction. This serpentine belt goes around the AC compressor, above the AC tensioner,under the crank pulley, around the power steering, over the alternator pulley, under the idle pulley, around the w/p,and behind the tensioner.ÊÊ

Read more

Routing new serpentine belt on 94 Plymouth Voyager?

When routing a new serpentine belt, make note of how the old belt was routed. Take a picture of the belt routing if possible. Also most cars have a sticker under the hood with the routing on it.

Read more

Can a serpentine belt be put on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

Can you put a serpentine belt on backwards?

you actually can put a belt on backwards.grooves go to grooves, and smooth goes to smooth.but you have to pay close attention to the belt routing diagram.if the belt is put on the wrong way it can spin the water pump reversed causing an overheat condition very fast after starting.

Read more

Change power steering belt and alternator belt 2002 Mitsubishi montero sport?

The power steering unit and the alternator are both driven by the serpentine belt. Loosen the tensioner pulley and the serpentine belt will become loose. Put the new serpentine belt on and tighten the tensioner pulley.

Read more

Where is the serpentine belt tensioner on a 2.4 liter Dodge Stratus?

On my 2004, there are 2. Check the diagram on the fender well or near the radiator. It shows all the pulleys the belt goes around, including the tensioners.

Read more

How often is cabin filters changed?

I change mine every 2 yrs. depends on driving conditions, pollen, dust etc.

Read more

Can you help changing V-belt to serpentine using an electric water pump?

The big issue isn't an electric water pump, but the fact that you have to replace the pulleys. If you can pull that off you should be good to go, even with a belt-driven water pump.

Read more

What is the difference between a serpentine belt and an accessory belt?

An accessory belt is any belt that drives additional power systems from the front crank of an engine. Typically, these "accessories" are the alternator, power steering pump, and air conditioning compressor. In many rear wheel drive vehicles, a belt is also used to drive the radiator fan. Typicall...

Read more

How often is cambelt change Renault clio?

Depends on the model - for diesels its every 72000 miles but I'd recommend changing it at 54000 as I've heard some horror stories of cambelts breaking at between 64 - 72k

Read more

How to Change belt on vs commodore?

I'll Quote for you the directions given by the Gregory's Manual (No 268 for Commodore Lexen V6 1995 - 1997)Drive Belt:The Drive Belt tension is controlled by a tensioner assembly which maintains the correct tension on the drive belt and compensates for wear and stretch.The tensioner assembly is e...

Read more

How much does it cost to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

Why cant you detension the serpentine belt tentioner the bolt keeps rotating and not letting you get the belt on?

because the bolt is striped or you pulley is no bad take it off and get another one

Read more

How often should you change brake pads on a motorcycle?

Now that the brake pads have been swapped, it is time to check the brake fluid.The brake fluid level should be brought to the upper fill mark on the reservoir.Brake fluid should be completely replaced along with a flush of the entire system, about every two years.

Read more

How long does it take to replace serpentine belt?

How Long Does It take To Replace A Serpentine Belt? For professional automotive technicians with the right tools and training the replacement of a serpentine belt usually takes about 30 min to an hour.This time varies by the make, model, and year of vehicle that you're driving as some take longer...

Read more

How long can a car drive without a serpentine belt?

Not very long if it powers the water pump, -possibly 5-7 minutes before you overheat.

Read more

How do you change the air filter on 2010 Lexus RX350?

How do you change air filter on 2010 RX 350

Read more

How do I change the PVC valve on a 1999 Lexus RX300?

The PCV valve is located on the passenger side rear valve cover. Simply pull it out then pinch the clamp to release the valve. I would recommend replacing the PCV valve grommet while you're in there, they get hard and brittle and can break into pieces that fall inside the engine.

Read more

Will a serpentine belt failure damage the engine on the 2001 Rodeo V6?

Not usually but it can be an indication of a problem with one of the driven accessories.A timing belt in many circumstances can indeed do damage if it breaks so replace it at the proper intervals.

Read more

How long does a Toyota serpentine belt last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

How do you reroute serpentine belt to bypass ac compressor on 1995 town car?

If that model was available without a/c, you will need to purchase the belt for a 95 town car w/out ac, and follow the appropriate belt routing diagram for that model.

Read more

How do you repair a driver and passagner seat belt not retracting on Lexus 1998?

With Seat Belt Issues, don't chance it. If it's not working properly you are best off to just replace it. V-

Read more

How do you stop serpentine belt from squeeking?

Replace belt and check all pulleys for wear or rough spot

Read more

How often should you change the brakes?

It would depend on the driver's habits and the vehicle. I would recommend they be inspected by a mechanic every 10K or once a year.

Read more

When to replace the belts on your 2002 vw jetta?

The belts on a 2002 VW Jetta do not need to be replaced unless they are starting to show signs of wear. To avoid getting stranded on the road from a broken belt, it is a good idea to purchase a new belt and keep it in the trunk until needed.

Read more

How do you replace a serpentine belt on a 1995 Chevrolet Camero?

Replacing the serpentine belt on both V6 & V8 rear drive engine are fairly easy than front wheel drive. The belt is located just between the front of the engine and the radiator. You have plenty of clearance to work. Just need to losen the tension and the belt should come out. Putting the new...

Read more

How do you install serpentine belt on 88 Chevy silverado 4x4 350 auto?

Loosen tensioner and follow label (under hood) for routing

Read more

Need to find out how to replace serpentine belt?

Just pry the belt tensioner back and remove the old belt, and install a new one.

Read more

How do you align a serpentine belt pulley?

Read more

How do you release serpentine belt on a 89 Mercury Cougar?

You have to release your tensioners in order to release your serpentine belt. When you put the belt back on you have to follow the diagram on the hood of your car.

Read more

How often should you change spark plugs on a Harley?

Read more

How often change spark plugs on 2004 Toyota Camry?

Every 100K or when necessary.

Read more

How do you adjust serpentine belt on a 1999 Holden jackaroo?

On all U.S. vehicles that use A single serpentene the belt has an automatic tensioner. I suspect that your can does too. It could be stuck.

Read more

How do you install a serpentine belt on a 99 Isuzu Rodeo?

There is a belt tensioner (spring loaded pulley that automatically keeps the belt tight) that needs to be temporarily slackened while the now loose belt is slipped off one of the accessories. Sorry, but I can't remember what tool is needed to loosen the belt tensioner. Just opening the hood and o...

Read more

How often do seat belts fail?

Seat belts fail with startling regularity in motor vehicle crashes and lead to severe injury and even death.The National Highway Traffic Safety Administration (NHTSA) reports that roughly 3 million people each year suffer injuries and 40,000 people die because of seat belts that fail during crashes.

Read more

How often do timing belts fail?

Unfortunately, in most cases, there are no obvious signs the timing belt is near death; it will just break.That's why highly rated auto mechanics recommend replacing it every 60,000 to 100,000 miles.Always check your owner's manual for the manufacturer's recommendations.

Read more

How often should oil be changed on a 2000 corolla?

About every 3000-6000 miles

Read more

What are the signs of a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

What is a serpentine belt in a car?

A rubber belt that goes around all pulleys & has idlers as tensioners. On cars there are either v belts (belts shaped like a "v" that are tightened by moving accessories) or serpentine, which is usually one ribbed belt with idlers.

Read more

Is it OK to drive with a bad serpentine belt?

If the serpentine belt completely fails and breaks, then your car will break down.If the power steering fails when the vehicle is moving it could cause serious safety issues.Preventative maintenance is one way to make sure your belt does not break while you are driving.

Read more