How do you tighten a bolt nut?

Securing the Bolt with the Nut Then grab the head of the bolt so that it doesn't move around and hold it still while you spin the nut clockwise, gently pressing down on it.

Keep spinning and adding pressure until the nut is against where the bolt comes out of the hole and holds the two objects together.

Previous questionIs parking on the lawn illegal?
Next questionHow many cars can you park in your yard?

Related question

Do you tighten the nut or bolt?

The question is often asked as to whether the nut or the bolt head should be tightened.The answer depends upon which tightening process is being used.For torque controlled tightening whether the nut is tightened and the bolt head held, or the bolt head tightened and the nut held, can be of import...

Read more

Should you tighten the nut or the bolt?

There is no simple answer to this as in some instances, it is perfectly acceptable to tighten the bolt head while holding the nut in place.In other situations, it's acceptable to tighten the nut.It all depends on the application and the condition of the product or material being worked with.

Read more

Do wheel nuts tighten as you drive?

The reason for this is that the wheel bolts can loosen over time, meaning the wheel is no longer seated as tightly as it should be.After all, car tyres are subjected to heavy stresses on the road.You can prevent this by tightening the wheel nuts using a torque wrench whenever necessary.

Read more

How do you remove an over tightened nut?

Read more

How spanner tightens the nut?

In a clockwise direction.EDIT:an easy way to remember which direction to twist is: Lefty Loosey, Righty Tighty

Read more

How tight should you tighten a wheel bearing nut?

Pre-Loading Trailer Wheel Bearings Tighten the spindle nut finger tight (until snug) and then with channel-lock pliers or a crescent wrench, tighten the spindle nut another 1/4 turn or about 15 to 20 ft pounds of torque.

Read more

How do you remove an over tightened bolt?

Read more

How do you loosen an over tightened bolt?

How to Loosen Tight Bolts Clean around the bolt with a wire brush, removing as much external buildup as possible.Try loosening the bolt with a wrench. Gently tap the wrench with a tool such as a a small hammer or chisel, and try loosening it with a wrench again.Use a propane torch to heat th...

Read more

How tight should lug nuts be tightened?

Tight is good, but over tighten is NOT.Over tighten can stretch the stud and cause failure around the rotor.Every car has a lug nut torque specification from the manufacturer.The proper way to tighten the wheel is to use a torque wrench to torque every lug nut to its recommended torque when the c...

Read more

Can you over tighten lug nuts by hand?

The problem with impact guns is they're so powerful, one can easily over-tighten the nuts.A torque wrench measures the tightening force applied, allowing the user to accurately follow the manufacturer's recommendations.If your lug nuts were tightened by hand I wouldn't be too concerned.

Read more

Do you torque the bolt or the nut?

The answer depends upon which tightening process is being used.For torque controlled tightening whether the nut is tightened and the bolt head held, or the bolt head tightened and the nut held, can be of importance.The general objective from a tightening process is to achieve a consistent bolt pr...

Read more

How do I keep my nuts and bolts tight?

How to Prevent Nuts From Loosening Thread a self-locking nut on the bolt and tighten with the appropriate wrenches.Slip a split, or lock, washer over the bolt end. Paint thread-locker compound all the way around the bolt threads as far down as possible. Thread the nut on the bolt and tighte...

Read more

What happens if you tighten lug nuts too much?

Mechanics use a torque wrench to properly tighten the lug nuts on your car.Using too much torque can damage the vehicle.Using too little torque can cause the wheels to come loose.You can find the amount of torque required for your vehicle in the owner's manual or you can ask your mechanic.

Read more

Should you use an impact wrench to tighten lug nuts?

When loosening a lug nut you'll notice the socket attached to the impact wrench moving slowly as the lug nut is loosened and then quickly when it's loose.Be cautious when tightening lug nuts using an impact as it's easy to over torque them—which can stretch or even strip the threads.

Read more

How much torque is needed to tighten lug nuts?

You're now twisting that nut with 10 ft-lb (distance times force, or 1 foot times 10 pounds).Use a 2-foot-long wrench and apply 50 pounds of force, and you'll have 100 ft-lb, which, happily, is just about as long as most lug wrenches, and as much force as most elbows are happy cranking on.

Read more

Will tightening oil pan bolts Stop Leak?

When the bolts get loose, they do not apply enough pressure to the Oil Pan Gasket.When this happens, Oil gets past the Oil Pan Gasket.The Oil then drips down the side of the Oil Pan.Before attempting to change the Oil Pan Gasket, try tightening the bolts evenly until they are tight.

Read more

How do you tighten a boat throttle?

Read more

How do you tighten a belt?

Method 1 Tightening the Drive Belt with the Alternator Disconnect the battery. Loosen the bolts attaching the alternator to the bracket. Use a piece of wood as a pry bar to increase the tension on the belt. Tighten the alternator bolts in the new location. Check the belt tension. Reconne...

Read more

How do you tighten a steering wheel?

Use a wrench to loosen but not remove the lock nut.Use a screwdriver to tighten the worm gear screw 1/4 turn clockwise.Tighten the lock nut again.Return to the driver's seat and examine the play on the steering wheel again.

Read more

What is angle tightening of bolts?

"ANGLE CONTROLLED TIGHTENING.A tightening procedure in which a fastener is first tightened by a pre-selected torque (called the snug torque) so that the clamped surfaces are pulled together, and then is further tightened by giving the nut an additional measured rotation.

Read more

How do you loosen a lug nut?

Use the appropriate tool to loosen the lug nuts.Before jacking the car up, use your wrench or tire iron to break the lug nuts loose.Do not remove them completely, but turn them a quarter turn or so in the counter-clockwise direction each to make them loose enough to unscrew while the vehicle is i...

Read more

How do you remove a locking nut?

Read more

How do you loosen a jam nut?

Read more

What is a bolt without a nut called?

A bolt without a nut or a head is called a stud.

Read more

Are steel rods like nuts and bolts?

They can be made of the same material but they are not the same. A rod is a rod and a nut & bolt are not even close to being the same thing although a nut & bolt may start out as a rod of steel.

Read more

How do you undo a seized nut?

Soak it with penetration oil for days or heat it cherry red with a torch or split it with a chisel.

Read more

How do you loosen a hub nut?

Read more

How do you tighten an aerial on a Nissan Qashqai?

Jennifer,I was thinking the same thing wihnisg I could like the posts and comments on this blog. It gives me hope to read this when I feel like we are bombarded with so much bigotry and close-mindedness. There are more empathetic people out there than we realize.Libby

Read more

How do you tighten a timing belt tensioner pulley?

To even out the tension in the belt, use a spanner or socket wrench on the crankshaft-pulley bolt and turn the crankshaft two full turns clockwise.Tighten the locking bolt first to hold the tensioner in its new position.Tighten the pivot-spring bolt, which has a precise torque setting.

Read more

What is the head gasket bolt tightening sequence?

Get a Haynes Manual, A Chilton Manual. You can get them at Autozone, Advance Auto, or Napa. They Run under $20. And they are very helpful.

Read more

What tools used for tightening bolts according to present torques?

To do this, you will use a torque-wrench. You don't usually torque a bolt to the present specifications, but you get the proper specification numbers out of a service manual. There is information on-line that will tell you the proper torque specifications of pretty much every bolt and nut in a ve...

Read more

Are head bolts tightened past their yield point?

To achieve this the TTY head bolts are tightened past their yield point into the plastic phase.In other words if the bolt is tightened past its yield point it will not return to its original dimension or state when the loading is released.This is due to plastic deformation!

Read more

How do you tighten auto fan belt?

first you have to locate the allready plced soket and then just tighten the belt

Read more

How do you tighten Dexter Axle bearings?

Read more

How do you tighten rear shockies on a eb falcon?

YOU CANT THERE NON -ADJUSTIBLE, YOU HAVE TOO REPLACE THEM IF THAY ARE BUGGERD

Read more

What is fiat punto head bolt tightening sequence and torque?

It is important to know the head bolt tightening sequence and the torque of a vehicle. For the Fiat Punto it is 20nm, 30nm, 90 degree turn, 90 degree turn, then in order 8,6,2,5,10,7,3,1,4,9.

Read more

How do you split a nut with a chisel?

The chisel blade should be directly over the drilled hole.Strike the head of the chisel repeatedly with a hammer until it splits and can be removed from the bolt.If you're having a hard time after you've split one side, drill a hole on the other side of the nut and split the nut into two halves.

Read more

How do you get a stripped thread off a nut?

Then hit the cuts with a chisel and a hammer a few times, thus splitting the nut or bolt and relieving the tension on them.With nuts you can normally just split it off of the bolt, clean up the threads, and install a new nut.With bolts you can use some locking jaw pliers to grab the bolt head and...

Read more

How do you tighten loose steering head bearings?

Most Motor cycles have an adjuster nut and lock nut at the top of the stem. This is just under the handle bar mounts.

Read more

How can you tighten a tonneau cover?

Many vinyl tonneau covers come equipped with a tension control adjustor to help resolve this very issue. The reason is simple - during the winter, the cold weather causes the vinyl to contract, while in the summer the opposite will happen. The heat will cause the vinyl to loosen a bit which will ...

Read more

How do you loosen a nut left or right?

Typical nuts, screws, bolts, bottle caps, and jar lids are tightened (moved away from the observer) clockwise and loosened (moved towards the observer) counterclockwise in accordance with the right-hand rule.

Read more

How do you remove a difficult bolt?

WD40 and some elbow grease

Read more

How many lug nuts do you need?

A lug nut is also called a wheel nut, and is used to hold the wheel securely onto the vehicle.Depending on the type of vehicle you have, you may have four, five, or six lug nuts.

Read more

How do you remove a broke bolt?

Insert small bar having enough length in contact with bolt and then do stud arc-welding between bar & bolt.Then turn it as per thread direction.Thus we can remove broke bolt.

Read more

How do you remove a broken bolt?

Search for "stud extractor". Looks like a drill bit but the cutters are left hand thread, designed to be used with the drill in reverse. The lid of the box or the extractor should be marked to indicate a) the screw size they are designed to extract b) the drill bit size you use to drill a hole fo...

Read more

How do you remove a rounded off nut?

A quick way to get the bolt back to the good part of the threads is to wedge a small screwdriver or flat blade between the part and the bolt, nut, or screw head.Apply pressure to push the bolt out and unthread it.This works miracles.Sometimes the hole itself is stripped.

Read more

How do you remove a stuck axle nut?

Read more

What is 1968 F 250 lug nut bolt pattern?

Well have you seached that on yahoo or you coud go to a car dealer and ask himI hope that helps

Read more

How do you tighten a Fan belt on a 3 Ton Dump Truck. Do you adjust the water pump or the Alternator to tighten it?

Alternator would have to be tightened if it is an older vehicle that allows you to do so.

Read more

How would you tighten a loose fuse on a car?

It depends... If the fuse is loose because some foreign object (like a multimeter probe) had been jammed into the socket you might be able to pry the socket closed with a jewlers screwdriver and restore the grip. If that doesn't work, you could insert a thin shim. I have seen this problem when th...

Read more

How do you get a stuck lug nut off?

Method 2 Loosening Stuck Lug Nuts Double check that the parking brake is on. Get additional leverage. Use your foot. Use a mallet or hammer. Use a penetrating oil if the lug nuts are rusted to the stud. Use a wheel lock remover to remove locked lugs. Use a torque wrench when replacing l...

Read more

Can bolt's and nuts be made of tool steel?

YesYes but it would depend on the application of the nuts and bolts if they would function safely. You can even make nuts and bolts from wood if the application allows it.

Read more

How do you tighten front bearing on 05 Rodeo?

Need to know which bearing and which Rodeo. There is a Isuzu Rodeo and a Holden Rodeo. Each has several bearings.

Read more

What breaks first the nut or the bolt?

Bolts will usually break first if twisted enough.

Read more

Why is your tire still loose after lug nuts were tightened?

their could be a few reason's, most common is the tyrod or tyrod ends are no good. or in a worse case the wheel barring is no good

Read more

How do you tighten a chain on a 2005 yfz 450?

loosen up the tire then pull it back and tighten it at the same time and it will be much tighter

Read more

How do you remove anti theft lug nuts?

Time Required Step 1: Look for the damn key. Don't give up so easily! Step 2: Figure out what size socket is 'close,' make sure it's a 12-Point. Step 3: Smash that socket onto the locking lug nut with a hammer. Step 4: Apply leverage. Step 5: Revel in your success! Step 6: Get the lockin...

Read more

How do you know which spanner for which nut?

Learn through repeated practice or just try the ones that look close to find the fit.Metric wrenches are easier as they do large jump between sizes.

Read more

How do you remove a seized bolt from aluminum?

Best way to remove rusted steel bolts from aluminum parts Use a propane torch to heat the bolt.Cut the bolt at almost surface level then. Do a cone drill and a cone bolt tip, arc weld the bolt. Do a passing-through drill almost the bolt diameter to make it weak, then pass another threader, an...

Read more

How do you remove a stripped Allen bolt?

Step 1 Removing Stripped Counter-Sunk Allen-Key Bolts Cut a slot into the screw head.Place a screwdriver in the slot and tap with a hammer in the counter-clockwise sense to loosen the bolt.Unscrew the bolt with the driver.

Read more

How do you measure the bolt pattern on a rim?

Read more

How do you get a stripped oil pan bolt off?

Read more

How do you loosen a bolt that won't budge?

Read more

How do you tighten a chain on a tt-r 125?

loosen the rear axle and move the tire back

Read more

How do you tighten a sloppy steering coulmn on a 1987 yj?

This question is not answerable. There are several problems that would cause this and they are all serious safety problems and need to be at least checked by a knowledgeable person.

Read more

How do you remove a broken bolt with an easy out bolt?

Each extractor has a drill bit size stamped on it, making selection a simple matter.Insert the easy out into the hole drilled in the center of the broken bolt or screw and then gently tap it home with a hammer so it bites into the metal of the bolt or screw.

Read more

How do you undo a cross threaded bolt?

I own a 1991 Mercedes and was well overdue for new brakes. Upon inspection, I had three cross threaded wheel bolts. If you have this problem on an older car with long seemingly impossible bolts like me, I have the answer. The head broke off of two of the bolts so any normal attempt through drilli...

Read more

How do you get locking wheel nut off wolfrace alloys?

Well you should have the key that you place on the jack when you take off the tire. If it's lock nuts then you can only get it off by using the nut key along with the jack handle.

Read more

How do you loosen tight lug nuts on aluminum rims?

got the same problem.. so far all I found was this.. http://www.garrettwade.com/jump.jsp?itemType=PRODUCT&itemID=105477haven't bought or used it yet..and here http://answers.yahoo.com/question/index?qid=20080518195536AAVm2yMyou out!!

Read more

How do you use Rawl bolts?

How to Use Rawl Bolts Mark an "X " on the base material where you will drill a hole to install your fixture. Center the fixture template hole over the area where the hole in the base material will be drilled. Insert a carbide tipped drill bit in the chuck of a hammer drill.

Read more

How do you tighten a chain on 2004 Yamaha raptor 660?

Owners manual, or go to related link below

Read more

How do you tighten an alternator belt on a 2003 murano?

All you do is look for the tension pulley and tighten it, see below

Read more

How do you tighten the steering column in a GMC 1991 Sonoma?

If your referring to having loose steering, then you need to tighten the adjustment set screw on the steering box under the hood. Don't tighten this to much, or it will lock up the gears. Typically a loose box needs to be replaced, in very few cases will tightening the set screw actually help.

Read more

How do you tighten the chain on a 2007 Raptor 700?

first, loosen the 4 screws at the bottom by the chain second, take a screw driver, or a thin rod, and insert it into 1 of the two holes on the left side of the sprocket in the rear barron third, push forward to loosen the chain and pull forward to tighten it. Lastly, tighten back the four screws....

Read more

How do you tighten the serpentine belt on a 1997 Saturn?

You don't. The belt tension is automatically adjusted via a spring loaded tensioner. If the serpentine belt is noisy or worn out prematurely. replace the tensioner. The belt should be inspected for cracks and other signs of wear. Replace worn out belt(s) before they break leaving you stranded.

Read more

How do you tighten the fan belt on a corsa 1.2?

If it is a newer corsa (built in the last 12 years or so) if guessing you mean the alternator belt because it doesn't actually have a fan belt as the fan is driven by a electric motor.To tighten the alternator belt is very easy...Just loosen the two or three bolts holding it on (do not take them ...

Read more

How do you drill out a broken bolt?

Method 1 Using an Extracting Kit Center punch the broken bolt as close to the center as possible. Drill a pilot hole into the center of the broken bolt with the left-handed drill bit. Place the appropriate-size extracting bit into the hole you created with the drill. Remove the broken bolt...

Read more

How do you measure torque on a tight bolt?

Loosen the bolt using a torque wrench and read the torque when the bolt starts moving.Tighten the bolt further to determine the applied torque.Read the torque when the bolt starts moving again.Mark the position of the tightened bolt, loosen it and read the torque when retightening it up to the ma...

Read more

How do you remove a rusted broken bolt?

Read more

What are the correct tightening procedures for cylinder head bolts after head gasket replacement?

The correct procedure depends on the engine and needs to be based on the manufacturer's guidelines. Starting from the center and working outward in a spiral is a typical approach.Each engine is different. Every manufacturer has a slightly different method. As a general rule the cylinder head bolt...

Read more

Do you need a lock washer with a lock nut?

They require that a cotter pin be placed through a hole in a bolt and through the crown of the nut.We consider these to be lock nuts because the cotter pin will hold the nut in place if it comes loose.Keps K lock nuts Have an attached spinning washer with teeth that can dig into the assembly.

Read more

How do you remove lock nut on rim?

You're meant to use a specially keyed socket.If you don't have that, tire shops usually have a set of removal Tools.

Read more

How do you measure bolt patterns?

Measure from center of one lug (stud that the lug nut bolts on to) to the center of the lug directly across from it if you have four-, six-, or eight-lug hubs. Measure using the metric side of the ruler, in millimeters. So if you have a four-lug hub and the measurement came out to 100mm, the bolt...

Read more

How do you determine bolt fastening torque?

It depends on what the bolt is made out of ,if it is metric or standard, the thread pitch and what you are screwing into and if you torque it dry or lubricated... but ALL BOLTS HAVE A TORQUE:If it is a bolt going into the block for example: the manufacturer has a specific torque it needs to be at...

Read more

How do you remove anchor bolts?

How to Remove an Anchor Bolt From Concrete Determine the size of the anchor bolt head. Remove the anchor bolt from the concrete by turning the bolt counterclockwise with the socket. Use a bolt extractor on a stubborn bolt. Insert the awl into the anchor hole. Cut off the bolt head, when n...

Read more

How do you loosen tight bolts?

Read more

What is the purpose of a washer for bolts and nuts?

So when the nut is screwed on it will widen out the area of pressure so the nut hold longer.

Read more

How do you tighten the parking brake on a 1991 Geo Tracker?

Make sure service brakes are adjusted properly Emergency brake adjuster should either be under vehicle at junction of cables or at the side of the handle between the seats (May have to remove plastic trim) Set parking brake at 3 clicks-wheels should be held firm at this point

Read more

What does nM stands for in torque reading in tightening bolts?

Newton Meters. 1 ft lb is ~1.3558179488410815 Newton Meters.Newton Meter. One newton meter is equal to about 0.74 lb ft.

Read more

How do you change a glove box latch on a 88 GM Van. It's loose. Need to remove the trim ring to access tighten the nut. Small hole in center but unable to get it loose. Thanks very much?

have you adjusted th inside latch, it goes up an down adjustabley via two Phillips screws.have you adjusted th inside latch, it goes up an down adjustabley via two Phillips screws.

Read more

Why do you torque a bolt?

Torque is used to create tension.Bolts are used to affix two components so that they can resist tensile (pulling apart) and shearing (sliding apart) forces.After the nut has been turned onto the bolt, additional torque causes the nut to turn and stretch the bolt.

Read more

What are the torque settingsand tightening sequence for the cylinder head bolts on a Kia Sedona 2.9?

http://wiki.answers.com/Q/What_are_the_torque_settingsand_tightening_sequence_for_the_cylinder_head_bolts_on_a_kia_sedona_2.9 the cylinder head bolts on a kia sedona 2.9?"

Read more

How do I remove a lug nut without the key?

Time Required Step 1: Look for the damn key. Don't give up so easily! Step 2: Figure out what size socket is 'close,' make sure it's a 12-Point. Step 3: Smash that socket onto the locking lug nut with a hammer. Step 4: Apply leverage. Step 5: Revel in your success! Step 6: Get the lockin...

Read more

How do I remove a stripped bolt?

Then hit the cuts with a chisel and a hammer a few times, thus splitting the nut or bolt and relieving the tension on them.With nuts you can normally just split it off of the bolt, clean up the threads, and install a new nut.With bolts you can use some locking jaw pliers to grab the bolt head and...

Read more

How do you remove a lug nut when the wheel stud is also turning?

turn the car offDon't jack up the wheel until you loosen the lug nuts.Find some one who is good with a cutting torch, they can cut that nut off without damaging the rim. You will have to replace that stud or maybe the hub assembly.

Read more

How do you get a striped nut off the power steering mounting bracket?

Alot of people confuse stripped with rounded, is the nut rounded so that you cannot turn it with the proper size wrench or are the threads damaged so the nut spins but will not come off?

Read more

How do you hold crank shaft pulley wheel to losen nut on a renualt clio 1.2?

easiest way to loosen nut is to put the engine in gear if a manuel shift or put in park if an automatic

Read more

How do you get a nut that is burred on the edges off?

Refile the nut so you have new flat surfaces

Read more

How do lug nuts fall off?

Pressure will also be placed on the vehicle as it turns corners, brakes, or accelerates to high speeds.All of these combined can cause other lug nuts to come off, or the studs to snap.The studs are what the lug nuts attach too, and hold the wheel on.So if the stud snaps, the wheel could fall off.

Read more

How much do a large bolt weigh?

It depends on what you consider large. A large bolt in a car would be a,crank bolt 7/8 x 3 inch- 10oz.control arm bolt/ head bolt 3/8 x 5 inch-5oz.U bolt for a solid axle - 8-10 oz.I would consider a 1 pound bolt as large.Some examples:3/4 inch bolt 6 inches long is 1lb.1/2 inch bolt 18inches lon...

Read more