How do you tell if the starter or the flywheel ring is bad on a 1993 Mazda 626 lx?

Cars & Vehicles

Remove the starter and inspect the ring gear on the flywheel.

Previous questionWhat does the term muscle car mean?
Next questionWho discover auto?

Related question

How do you tell if your starter is bad or battery?

Read more

How do you determine what causes a squeaky fan belt on a 1993 Mazda 626 when the car is first started up or the ac is turned on?

Sounds like your A/C pump is seizing try removing the belt and turn both the center and outer wheels on the front of A/C pump by hand with ingnition off the outer wheel should spin free and inner wheel should have slight resistance (not hard to turn)if ok check any jockeys if all ok try replacing...

Read more

Why doesnt the cooling fan on a Mazda 626 lx not turning on?

probably the fan relay

Read more

How high should rpms be in a 1993 Mazda 626?

no more then 900 in park. 750 to 800 is good

Read more

How can you tell if the starter relay is bad on 1998 Ford Taurus?

Find the relay. Take a test light (you may need to insert a back probe or paper clip to make contact). Check for power at the 30 pole. That should always be hot, at least with the key in the 'accessory' position. If you have power there, put it to the 86 pole while someone keys the car on. You sh...

Read more

How do you tell if you need a new battery or starter for your car?

go to your local garage/mechanic and ask him/her to check the charge in your battery

Read more

Where is the washer fluid pump on a Mazda 626?

most washer fluid pumps are on the resivour itself

Read more

How do you tell if the stater solenoid is bad or not?

if the started doesnt do anything its the solenoid if it just clicks and spins its the bendix

Read more

How do you tell if Chevy fan blower resistor is bad or the selector switch?

Examine the back of the switch for loose or melted connections. Then examine the resistor for burned spots. In most cases a burned resistor is the result of a failing blower motor. So if a new resistor burns out in a short time, replace the motor also.

Read more

How do you tell if a solenoid is bad?

Only by knowing beforehand its internal resistance, is possible to tell if it is bad, by measuring its resistance (DC current). If it dropped to a lower resistance it is short-circuited, and so it's bad. If the solenoid doesn't attract or attract with less power it is also a sign that it is bad.

Read more

How do you tell if a fusible link is bad?

The fusible link is essentially an in line fuse on the positive terminal of the battery.To determine if the fusible link has been blown , one test lead of your ohmmeter should be on the positive terminal of the battery and the other test lead should be on the end of the fusible link going to the ...

Read more

How do you tell if the distrbutor is bad?

It all depends on the problem,you should look for cracks around the cap,hard to start,moisture,losemess,backfiring,or no spark.Apluswrecker cash for cars Orlando 407-666-4216

Read more

How do you adjust the parking brake on a 1995 Mazda 626?

The majority of time if you adjust the rear brakes it will adjust the park brake.

Read more

How do you know if your starter is bad or your alternator?

Read more

How can you tell if starter is bad in 95 lodsmobile aurora?

When you turn the ignition u will hear a clicking noise,an my take 3 or 4 tries until the engine starts or your aurora could loose power an may need to be jumped off. -Jake of Texas owner of an 95 aurora

Read more

How do you tell if its your starter or your battery?

Read more

How do you tell if your battery or alternator is bad?

If the above steps reveal that the battery is working, it's time to take a closer look at the alternator.There are certain signs of a bad alternator to look for: While running the car, note the brightness of the interior lights.If the dashboard gradually dims, the alternator is likely at fault.

Read more

Where are the timing belt markings located to time a 1993 Mazda 626?

I am not sure if it has any but if there is they will be down on the crank shaft pulley

Read more

How do you tell if a voltage regulator is bad on a 1998 Dodge Ram 1500?

The voltage regulator is responsible for regulating alternator output. Look at the volt gauge in the dash. If it is too high generally that means that the regulator is bad. Take the truck to Autozone and have them check it for you. They offer this service free of charge and will do it on the truck.

Read more

How do you tell if you have a bad alternator?

AnswerHey there friend To check if alternator is false or not there is a simple way of doing it without getting to tear entire car and cables apart. Before you do anything loosen the negative cable but so its still connected to batter.Start the vehicle, if cant slave it off and start it, while ve...

Read more

How do I stopthe fan from running on my Mazda 626 if the car is turned off?

If it's the one on the radiator, and it stops running after a few minutes, then it's been designed by Mazda to work like that.If it runs until the battery goes flat, you have a short circuit somewhere, supplying the fan with power.

Read more

How do you reset check engine light on a 1997 Mazda 626?

Go to Advanced Auto. They should be able to.

Read more

When should you do a tune up on a 1998 Mazda 626?

Consult your owners manual as it will be scheduled maintenance.

Read more

How do you tell if ignition coil is bad on a 1985 300zx?

Easy way is to run the large out wire to a ground, one post on the coil to a ground and one to positive. Do not allow the large wire to actually touch the ground, have it just above the ground so that you can see a spark.Warning: do not touch the large wire while the other are hot. It has a lot v...

Read more

How do you tell if your wheel bearing is bad on a Lincoln navigator?

Usually when a wheel bearing goes bad, it will begin to make a high pitch noise like a bad humming sound and the sound increases as the speed of the vehicle increases. Take it to a shop and find out if they will check it for you.

Read more

How do you tell if a cv boot is bad on 2005 Nissan quest?

Inspect the boot and look for a tear or hole. If you see any the boot is bad and needs replacing. The joint itself will pop, and make noises if it is defective. Inspect the boot and look for a tear or hole. If you see any the boot is bad and needs replacing. The joint itself will pop, and make n...

Read more

How do you tell if ABS pump is bad?

When the ABS system is not functioning then loss of traction, skidding, and hydroplaning are far more likely to occur under heavy braking conditions. Symptoms of a Bad or Failing ABS Control Module Unresponsive brake pedal. Brake pads require more effort to push. The ABS Light is on. The ...

Read more

How do you tell if opened canned tuna is bad?

How can you tell if opened canned tuna is bad or spoiled? The best way is to smell and look at the tuna: if the tuna develops an off odor, flavor or appearance, or if mold appears, it should be discarded.Discard all tuna from cans or pouches that are leaking, rusting, bulging or severely dented.

Read more

How do you tell if gas gauge is bad?

If it reads full and you run out of gas, haha Seriously, though, there are really two main reasons why your gauge would be bad. The first, and most common is a bad float/sending unit. The float/sending unit sits in your gas tank, and sends a signal down a wire to your gauge The signal varies in v...

Read more

How do you tell if your water pump is bad?

Here are 5 common symptoms of a bad water pump: Coolant Leak at the Front-Center of your Car. Rust, Deposit Buildup, and Corrosion of the Water Pump. Water Pump Pulley is Loose and Making Whining Sounds. Engine is Overheating. Steam Coming from your Radiator.

Read more

When do you need to change the timing belt on a Mazda 626 GXi 2.0?

It is important to know when to replace the parts within a vehicle. The timing belt on this car should be changed close to every 100,000 miles.?æ

Read more

How do you tell if your engine is bad?

Excessive oil use, excessive water use, major oil leak, excessive smoking, ask a certified mechanic

Read more

How do you fix starter 1994 accord lx?

It really can't be fixed, just replaced. fairly inexpensive for diy.

Read more

How do you fix a 98 Mazda lx that is stuck in park?

Start with checking the fuses.

Read more

How do you know if its the starter or alternator?

Signs the Alternator has Failed: You notice that your headlights or your dash lights flicker or get extra dim or bright.Or that your gauges are behaving strangely.If you jump start your car and it will start, but the engine dies right after the jump then it is most likely the alternator.

Read more

How can you tell if the vac-cum boaster on a 1976 pickup is bad?

The brake pedal becomes hard to push in order to stop the vehicle and when the brake is applied you may also hear a vacuum leak and the engine rpm at idle changes.

Read more

How can you tell if the o2 sensor is bad on a 2000 mercury sable?

The check engine light would illuminate and set a code for the bad O2 sensor.

Read more

How can you tell if the engine computer is bad?

If it heats up really fast under fair conditions

Read more

How can you tell if the solenoid is bad?

Read more

How can you tell if the ignition switch is bad?

Symptoms of a bad or failing ignition switch Car stalls while driving. One of the first symptoms of an issue with the ignition switch is a vehicle that suddenly stalls while the engine is operating. Car starts and then suddenly stalls. Issues powering on the accessories.

Read more

How can you tell if the brake booster is bad?

Symptoms of a Bad or Failing Power Brake Booster Hard brake pedal. The primary indicator of a bad brake booster is an extremely difficult-to-push brake pedal. Longer stopping distance. Along with a hard brake pedal, you may notice it takes the vehicle longer to actually stop. Engine stalls ...

Read more

How do you know if its the starter or battery?

The first indication your starter may be going bad is at the moment you try to start your car.If you turn the key and simply hear a clicking sound, or nothing at all, then it may be the starter.If they light up properly, then the problem is not with the battery and is likely the starter.

Read more

How can you tell if the master cylinder is bad?

Abnormal brake pedal behavior With constant use over time, the seals inside of the cylinder can wear out and form internal leaks.A bad brake master cylinder may result in a pedal that feels mushy, spongy, or slowly sinks to the floor when depressed.

Read more

How do you tell if your front or back brakes are bad?

How to Know When Rear Brakes Need Replacement Listen to the sounds of your brakes. The most obvious indicator your rear brakes need replacing is the squeaking that you hear when you press down on the brakes. Respond to the service light in your car. Check your brake fluid. Press down on yo...

Read more

How do you tell if front or back rotors are bad?

Read more

How can you tell if a diode is bad?

A diode is reverse-biased when the positive (red) test lead is on the cathode and the negative (black) test lead is on the anode.The reverse-biased resistance of a good diode displays OL on a multimeter.The diode is bad if readings are the same in both directions.

Read more

How can you tell if a light switch is bad?

How to Tell If an Electric Light Switch Is Bad Turn off the power to the light circuit at the breaker panel. Remove the screws holding the cover plate on the light switch with a slotted screwdriver. Remove the wires from the terminals. Test the switch with a continuity tester. Check the s...

Read more

Where do you add antifreeze in a 1999 Mazda 626?

I'm guessing that it has a closed radiator, so one would use the overflow basin to add liquids. Otherwise one would use the radiator cap..

Read more

How can you tell if a transmission solenoid is bad?

Signs You've Got a Bad Shift Solenoid The check engine light comes on: The TCM continuously monitors shift solenoid operation. Erratic shifting or shift slippage: The shift solenoids regulate the flow of hydraulic fluid for shifting. Transmission won't shift gears: A faulty shift solenoid c...

Read more

How can you tell if a motor mount is bad?

Symptoms of a Bad or Failing Engine Mount Impact noises coming from the engine bay. One of the most common symptoms associated with worn engine mounts are impact noises coming from the engine bay. Excessive vibrations. Another symptom of a bad or failing motor mount is excessive vibration. ...

Read more

How can you tell if a car fuse is bad?

Read more

How do you know if it is the valve stem seals or the oil rings?

Valve seals will usually cause smoke at start up, and much lees while running, rings will smoke badly while running, and may have issues with crankcase pressure.

Read more

How can you tell if a pulley is bad?

Symptoms of a Bad or Failing Idler Pulley Visibly worn pulleys. One of the first symptoms of an issue with an idler pulley is visible wear on the pulley. Belt squealing. Another common symptom of a possible issue with the idler pulley is squealing from the engine belts. Damaged bearing or p...

Read more

How can you tell if the EGR valve is bad?

Symptoms of a bad EGR valve include: rough idling or stalling.a smell of fuel.increased fuel consumption.pinging, tapping, or knocking sounds.failed smog test.Check Engine Light on.

Read more

What size gas tank is on a 1998 Mazda 626?

The 1998 Mazda 626 DX sedan fuel tank holds 16.9 gallons of gas. It gets 26 miles per gallon in the city and 33 mpg on the highway. The '98 626 produces 125 horsepower at 5,500 rpm.

Read more

How do you tell if your water pump is bad on Chevy 350?

The most obvious symtom would be overheating of the engine.

Read more

How can you tell if a circuit breaker is bad?

Swap it with another like breaker.

Read more

How can you tell if a VVT solenoid is bad?

Symptoms of a Bad or Failing Variable Valve Timing (VVT) Solenoid Check Engine Light comes on. Since today's modern cars are controlled by an Engine Control Unit (ECU), virtually all individual components are monitored by the ECU. Engine oil is dirty. This is more of a cause as opposed to a ...

Read more

How can you tell if a rod bearing is bad?

Read more

How can you tell if a glow plug is bad?

Usually bad or failing glow plugs will produce a few symptoms that can alert the driver of a potential issue. Engine misfires or decrease in power and acceleration. Engine misfires are one of the first symptoms of an issue with the vehicle's glow plugs. Hard starting. Black smoke from the e...

Read more

How to replace the ac filters on a 1989 Mazda 626?

This vehicle does not have a cabin filter. There is nothing to replace.

Read more

How do you change the cabin air filter located in a 2000 Mazda 626 V6?

There is no provision for this filter. Mazdas And More, Vista, California.

Read more

How do I know if my piston rings are bad?

Here is a list of the most common symptoms for bad piston rings: White or gray exhaust smoke.Excessive oil consumption.Low power for acceleration.Overall loss of power or poor performance.

Read more

How can you tell if you have a bad valve?

hook avacuum gauge to port vacuum should stay steady if it shakes valve train problem.Do a compression test. When you find the cylinder that has low compression, shoot some oil into the cylinder and take another reading. If the reading changes very little it is probably a bad valve. If the second...

Read more

How do you tell if alternator going bad?

Most people would take the vehicle to a mechanic to have it checked. A cheap way to tell if it is charging is to remove the positive battery cable from the battery while the engine is idling. If the engine dies, the alternator is not charging and should be tested. Some will squeak or make scrapin...

Read more

How can you tell if distributor bad?

You wont get any fire at all, or the vehicle will not keep timing

Read more

How do you tell if your overdrive is on or off?

If you want to know if it is on or off, there is an easy way.While driving on the highway, change the overdrive selector and see what happens.If engine speed (RPM) goes up, then overdrive is now off.If engine speed goes down, then overdrive is now on.

Read more

How do know if your starter is bad?

Read more

How do I know if my starter relay is bad?

Vehicle does not start. The most obvious warning sign that a problem with the starter relay exists is when the vehicle won't start when you engage the ignition process. Starter stays on after engine started. Intermittent issues starting the vehicle. Clicking sound coming from the starter.

Read more

How do you know if the piston rings in your car are bad?

Worn piston rings will cause your car to burn oil. It will smoke, and you'll have to add oil frequently. Additionally, the performance will fall off as compression is lost past the worn rings. There may be a "slapping" sound as the piston skirts slap the cylinder walls, and this will occur in cas...

Read more

Where is the fuel pump located on a 1997 Mazda 626 4-cylinder 2.0?

On a 1997 Mazda 626 4-cyl, the (electric) fuel pump is located inside the gas tank.

Read more

How do I know if my sourdough starter is bad?

Dark brown or pink starters have been contaminated.Immediately throw out the entire batch as this indicates the starter has gone bad.Smell your sourdough starter before each use.Expect the smell of fresh unbaked bread dough, or a yeast-like odor.

Read more

How do I know if my starter solenoid is bad?

First, turn the ignition key to the “On” position.Look for the large terminal posts on the solenoid where the thick red wires connect to the solenoid.Touch the metal shaft of a screwdriver to both of the large terminals at the same time.If the engine turns over and starts, the solenoid is bad and...

Read more

Is the starter or solenoid bad?

Sometimes your car starts, sometimes it doesn't.Intermittent operation can be a sign of a failing starter solenoid.Problems that might cause your car to act like it has a bad starter solenoid can include: Bad battery - If the battery voltage is low it will be unable to provide enough power to sta...

Read more

How can you tell if gasoline is bad?

Oxidized fuel often turns darker over time and may even smell sour.You can check stored gasoline by pouring some into a clear glass container and comparing it side-by-side with known fresh gasoline.If your old sample looks noticeably darker than the fresh gas, you have strong evidence the gas has...

Read more

How can you tell if your temperature gauge is bad?

Symptoms of a Bad or Failing Thermostat Temperature gauge reading very high and engine overheating. The first and potentially most alarming symptom will be the temperature gauge reading high into the red within the first 15 minutes of your vehicle engine running. Temperature changing erratic...

Read more

How can you tell if your EGR valve is bad?

Top Five Signs of a Bad EGR Valve Poor engine performance. A bad EGR valve is likely to have issues with the engine's performance. Look out for the engine warning light. The “check engine” indicator will light up on the dashboard when your EGR valve fails. Fuel odor. Failed emission test. ...

Read more

How can you tell if gas is bad?

Oxidized fuel often turns darker over time and may even smell sour.You can check stored gasoline by pouring some into a clear glass container and comparing it side-by-side with known fresh gasoline.If your old sample looks noticeably darker than the fresh gas, you have strong evidence the gas has...

Read more

How can you tell if rack and pinion is bad?

Symptoms of a bad or failing steering rack/gearbox Very tight steering wheel. Today's rack and pinion steering systems are supported by a power steering unit that utilizes hydraulic pressure to allow easy and quick steering wheel handling. Leaking power steering fluid. Grinding noise when s...

Read more

How can you tell if an alternator is going bad?

Bad alternator symptoms: Dim lights. The failing alternator symptom most drivers recognize is dim or flickering lights. Service engine light. Another obvious sign is the one your vehicle tries to tell you. Odd noises. Electrical issues. Engine stalling. Dead battery.

Read more

How can you tell if your catalytic converter is bad?

Read more

How can you tell if your torque converter is bad?

Signs of a Bad Torque Converter The first, and for a lot of people, most obvious sign of a bad torque converter is when the gears in the car's transmission begin to slip.When your transmission slips, it would feel like you're driving over ice or up a hill with a heavy package in the trunk.

Read more

How can you tell if water pump is going bad?

Occasionally they will fail without previous symptoms.

Read more

How can you tell if an 02 sensor is bad?

The check engine light would illuminate and the code(s) set would lead you to which O2 sensor is at fault or why the sensor set the code.

Read more

How can you tell if oxygen sensor is bad?

It's simple. The engine will work on a much higher RPM or it will shut down itself without giving you any other signs.

Read more

How can you tell if your alternator is going bad?

Bad alternator symptoms: Dim lights. The failing alternator symptom most drivers recognize is dim or flickering lights. Service engine light. Another obvious sign is the one your vehicle tries to tell you. Odd noises. Electrical issues. Engine stalling. Dead battery.

Read more

How can you tell if alternator is bad?

Bad alternator symptoms: Dim lights. The failing alternator symptom most drivers recognize is dim or flickering lights. Service engine light. Another obvious sign is the one your vehicle tries to tell you. Odd noises. Electrical issues. Engine stalling. Dead battery.

Read more

How can you tell if your clutch is going bad?

If you're experiencing any of the below symptoms, you may need a clutch replacement: Spongy, sticking, vibrating or loose clutch pedal when pressed.Squeaking or grumbling noise when pressed.Ability to rev the engine, but poor acceleration.Difficulty shifting gear.

Read more

How can you tell if your ignition switch is bad?

1.Car stalls while driving.One of the first symptoms of an issue with the ignition switch is a vehicle that suddenly stalls while the engine is operating.If the ignition switch fails while the engine is operating it may cut off power to the ignition and fuel systems, which will cause the engine t...

Read more

How do you tell if it's an alternator or battery?

Confirming the battery is the problem First, check the dashboard battery gauge.The battery should be giving a charge, even while the vehicle is off.If the dashboard lights are dim, something is likely wrong with your battery.Try turning on your windshield wipers, lights or automatic windows.

Read more

How do you tell if it is a ground problem or if the fuel pump is blown?

Consulting the wiring diagrams should reveal the location for the test port which activates the fuel pump directly. If the pump can be actuated in this fashion, allowing operation of the pump, then pressure and volume should be measured to determine if the fuel pump output is satisfactory. If so,...

Read more

How do you you know if your starter relay switch is going bad?

By taking it off and testing it for resistance with a digital multimeter.

Read more

How do you know when a starter solenoid is bad?

Intermittent operation can be a sign of a failing starter solenoid.Problems that might cause your car to act like it has a bad starter solenoid can include: Bad battery - If the battery voltage is low it will be unable to provide enough power to start your engine.Sometimes the starter itself is t...

Read more

How can you tell if oil is bad?

Read more

How can you tell if an EGR valve is bad?

Symptoms of a bad EGR valve include: rough idling or stalling.a smell of fuel.increased fuel consumption.pinging, tapping, or knocking sounds.failed smog test.Check Engine Light on.

Read more

How can you tell if your suspension is bad?

6 Signs Your Car Needs Suspension Repair Car rides roughly. Most people can tell their shocks or struts are wearing out when they begin to feel every bump in the road, or when every bump causes the vehicle body to "bounce." Drifting or pulling during turns. Dips or "nose dives" when stoppin...

Read more

How can you tell if an ignition coil is bad?

1.Engine misfires, rough idle, and loss of power.One of the most common symptoms associated with a faulty ignition coil is engine performance issues.As the ignition coils are among the ignition system's most vital components, an issue can cause spark to be compromised, which can quickly lead to p...

Read more

How can you tell if antifreeze is bad?

The coolant also runs through a small radiator-like device inside your car's dashboard. Symptoms of bad coolant Your coolant is dark, murky, smelly or full of debris. Your temperature gauge reads higher than normal. Your engine overheats.

Read more

How do you know when a starter fuse is bad?

Use a multimeter to check if the fuse is still conducting current. Set the multimeter to read Ohms and place one lead on one end of the fuse. Put the other lead on the other side and see if there is a reading. If there is, the fuse is whole. If there is no reading, the fuse is blown.

Read more

How do you connect starter wires on a Mazda 2.2 B2200?

there is one wire with a round connector, it goes on the lug, the other connectors are unique wire connectors and can only go one place, just match them up.

Read more