How do you restart a 2000 alero that broke the serpentine belt?

Cars & Vehicles
Serpentine Belts

Serpentine belts don't just break. There is probably an accessory that is locked up such as the alternator or a idler pulley. Check each pulley that the belts contacts and make necessary repairs before installing a new belt. Once you have done that just start the engine back up as you normally would.

Previous questionHow many hours do it take to go 80 miles if your going 80 miles per hour?
Next questionHow do you tell if it is diesel how does it smell?

Related question

How do you change a serpentine belt?

How to Replace a Serpentine Belt Take a good look at both your repair manual and your belt routing diagram under the hood before beginning. Look at the way the old belt wraps around the pulleys. Locate the self-adjusting tensioner and know that you need to be careful when releasing tension ...

Read more

How do you get the accessory drive belt or serpentine belt off of a 1989 sunbird?

To remove the accessory drive belt or the serpentine belt from the motor on a 1989 Sunbird, it is necessary to loosen the belt tensioner. Look for a pulley that has a bolt in a slot. Loosen the bolt and move the tensioner so there is a gap in the belt. Then remove the belt from each pulley.

Read more

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

How do you replace serpentine belt on a fx 35?

1. Remove front engine undercover.2. Loosen idler pulley (alternator and power steering oil pump belt) lock nut and adjust tension by turning bolt.3. Same is done for the other idlery pulley (A/C compressor belt).

Read more

How do you align a serpentine belt pulley?

Read more

How do you know if you need to flush the transmission on a 2000 alero?

Your owners manual lists a transmission oil change as regular maintenance.If someone is recommending a flush it would replace this service.If there is a fault and they are recommending a flush it is to late, the transmission needs repair.

Read more

Can you get a diagram of a serpentine belt for a 2000 Ford Escort ZX2 please?

lift the hood. usually there.

Read more

How do you do you find the serpentine belt diagram for a Toyota RAV4 2001?

There should be a diagram under the hood somewhere. Normally on the fan shroud. Click the link for a diagram. If you do not see one search with the term "2001 Toyota Rav 4 belt diagram" and you will find a diagram.

Read more

How do you remove factory stereo from 2000 Oldsmobile Alero?

is there 2 holes on each side of the radio : : like that

Read more

If the timing belt broke in a 2000 Mazda Protege 1.8 will the car be damaged?

A 2000 Mazda Protege with 1.8 DOHC engine appears to be a "free-running" engine, meaning there is no valve/piston interference in case the timing belt broke. There is enough clearance between the valve and piston, even if the cam stops (i.e. the timing belt breaks) with the valve fully open. Ther...

Read more

How do you remove serpentine belt on 2005 Chevy Cobalt?

You have to release the stress in the tensioners to remove the serpentine belt. When you put it back on there is a diagram under the hood of the car that takes you step by step.

Read more

Where is the tensioner pulley to tighten the serpentine belt on a 2000 Chevy Silverado?

If you're standing at the front of the truck and looking into the engine compartment the tension pulley is on the left side about half way down.

Read more

How do you stop serpentine belt from squeeking?

Replace belt and check all pulleys for wear or rough spot

Read more

How do you replace serpentine belt on 2005 Equinox?

Begin by loosening the tensioner pulley on your 2005 Chevrolet Equinox. The serpentine belt will become loose and can be removed. Reverse the process to install your new serpentine belt.

Read more

Do you have a diagram of how to put the serpentine belt on the pulley?

You may get an answer if you list the vehicle & engine you are talking about. You are not going to get an answer to this question as is.

Read more

How long do BMW serpentine belts last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

How do you change the serpentine belt on a 1994 mercury cougar xr7?

with a 1/2" rachet or breaker bar placed in the square whole on the tensioner pully, you push (from passenger side to drivers) which will release the presure on the belt. Might want to draw a "map" of how the belt goes cause it ain't obvious when its off the car.

Read more

How do you repair the serpentine belt on a 1998 Mitsubishi Galant?

You don't repair a serpentine belt. You replace the worn or broken belt with a new one.

Read more

Can you replace a serpentine belt yourself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How do you replace the serpentine belt on a 1993 Mercury Cougar?

To remove the serpenteen belt on this vehicle, you must first locate the spring loaded tensioner. You will need a 1/2" breaker bar or a socket to recoil the spring load. doing this will release the tension on the belt. You can then remove the belt.NOTE: If you are just changing the belt with a ne...

Read more

What does a serpentine belt do?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

How do you tighten the serpentine belt on a 1997 Saturn?

You don't. The belt tension is automatically adjusted via a spring loaded tensioner. If the serpentine belt is noisy or worn out prematurely. replace the tensioner. The belt should be inspected for cracks and other signs of wear. Replace worn out belt(s) before they break leaving you stranded.

Read more

Is a serpentine belt the same as a timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

How do you restart a computer on a Mitsubishi eclipse 2000?

Simply unplug the battery and replace the cords to the battery!

Read more

How important is a serpentine belt?

Well, it won't keep your pants up, but it does transport power to your vital automotive components.The serpentine belt is one long, snaking, winding belt that keeps your alternator, power steering pump, air conditioning and — in some cases — your water pump running smoothly and effectively.

Read more

How do you change a serpentine belt on a Chevy Silverado?

Shop Products Familiarize yourself with the belt routing diagram.Insert a 3/8 inch drive ratchet into the belt tensioner.Pull the tensioner counterclockwise to loosen the belt.Pull the belt off the idler pulley.Release the tensioner.Pull the belt off and out.

Read more

How do you replace a serpentine belt on a 1995 Chevrolet Camero?

Replacing the serpentine belt on both V6 & V8 rear drive engine are fairly easy than front wheel drive. The belt is located just between the front of the engine and the radiator. You have plenty of clearance to work. Just need to losen the tension and the belt should come out. Putting the new...

Read more

How do you change a serpentine belt on a 2001 Chevy Suburban?

Read more

How do you change a serpentine belt on a 2001 Chrysler Town and Country?

How to Replace the Serpentine Belt in a Chrysler Town & Country Open the hood and find the belt tensioner pulley. Look at how the belt is routed around various pulleys. Use a wrench to rotate the belt tensioner pulley bolt and slide the old belt off of the tensioner pulley. Make sure y...

Read more

How do you change a serpentine belt on a 2008 Toyota Corolla?

Read more

How do you install a serpentine belt on a 99 Isuzu Rodeo?

There is a belt tensioner (spring loaded pulley that automatically keeps the belt tight) that needs to be temporarily slackened while the now loose belt is slipped off one of the accessories. Sorry, but I can't remember what tool is needed to loosen the belt tensioner. Just opening the hood and o...

Read more

How do you change a serpentine belt on a Mazda 3?

How to Replace a Mazda 3 Serpentine Belt Open the Mazda 3's hood and support it with the prop rod. Connect the belt-tensioner tool into serpentine belt tensioner and move the tensioner pulley away from the belt with the tool. Pull the belt off the engine accessory pulleys by hand. Stretch ...

Read more

How do you release serpentine belt on a 89 Mercury Cougar?

You have to release your tensioners in order to release your serpentine belt. When you put the belt back on you have to follow the diagram on the hood of your car.

Read more

Is the serpentine belt the same as the timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

How do you adjust serpentine belt on a 1999 Holden jackaroo?

On all U.S. vehicles that use A single serpentene the belt has an automatic tensioner. I suspect that your can does too. It could be stuck.

Read more

How can you bypass a serpentine belt on a 2002 converible sebring from the ac compressor?

You realy can't. If your intention is not to power the A/C unplug the wire that connects to the electric clutch. It should be right behind the pully.

Read more

Can you drive a car with a broken serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Do you losen the altinator to change serpentine belt on a 94 Jimmy?

You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.

Read more

Can you drive a car with a bad serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Can you drive without serpentine belt?

Since the serpentine belt is generally the only accessory drive belt on vehicles these days, this is what you'll lose: Engine cooling* - The serpentine belt drives the water pump.Without the water pump, there will be insufficient coolant flow to maintain engine temperature, and you will overheat ...

Read more

How long can a car drive without a serpentine belt?

Not very long if it powers the water pump, -possibly 5-7 minutes before you overheat.

Read more

Can you drive with a bad serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Can you drive a car without a serpentine belt?

As you can see, driving without a serpentine belt is not an option, at least not for very long.*Some cars have an electric water pump and/or electric assist steering.

Read more

What happens if you put a serpentine belt on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

How often should serpentine belt be changed?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

How do you change the timing belt on a 2000 Hyundai Sonata?

http://www.google.com/search?sourceid=navclient&ie=UTF-8&rlz=1T4GFRC_enUS205US206&q=change+timing+belt+on+2000+Hyundai+Sonata http://en.allexperts.com/q/Hyundai-Repair-815/2000-hyundai-sonata-timming.htm Everything youneed is in those two links. Good luck.

Read more

Does the serpentine belt affect the transmission?

Effect of Serpentine Belts on Transmission.As a result, if the serpentine belt is worn out or breaks, it results in engine overheating and losing the powered steering and charging system.

Read more

How much does it cost to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How do you change the serpentine belt on a 2002 Chrysler town and country mini-van 3.8 engine?

There should be an idler pulley that you need to loosen to take belt off, draw a diagram of how the belt looks before you take it off so you can see how it goes back on.

Read more

How do you reroute serpentine belt to bypass ac compressor on 1995 town car?

If that model was available without a/c, you will need to purchase the belt for a 95 town car w/out ac, and follow the appropriate belt routing diagram for that model.

Read more

What is the serpentine drive belt?

The serpentine drive belt is the rubber belt that is connected to all the pullys 5-6 like the water pump, altenator, a/c clutch, fan, and crankshaft. usually located behind the radiator or on the side of the motor depending on what the motor is and what its in.

Read more

What happens when the serpentine belt breaks?

That means when your belt breaks, slips and, ultimately, wears out, everything—from the power steering pump to the alternator and air conditioner—stops working.What's more, the parts it controls can become severely damaged.Broken hoses and belts are bad; a damaged engine is even worse.

Read more

Can you put a serpentine belt on backwards?

you actually can put a belt on backwards.grooves go to grooves, and smooth goes to smooth.but you have to pay close attention to the belt routing diagram.if the belt is put on the wrong way it can spin the water pump reversed causing an overheat condition very fast after starting.

Read more

How much does it cost to replace the serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How do you know if your serpentine belt is going bad?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

How often does a serpentine belt need to be replaced?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

How long does a Toyota serpentine belt last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

Can I change a serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How can you tell if you have a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

How do you install serpentine belt on 88 Chevy silverado 4x4 350 auto?

Loosen tensioner and follow label (under hood) for routing

Read more

How do you route smaller serpentine belt on98 zx2 to bypass ac compressor?

The belt that I used my my 1999 ford escort ZX2 is a 6K730 to bypass the A/C. when routing the difference is the belt will come from the power steering to the tension pulley to the crank then water pump and the rest is normal. I hope this helps

Read more

How do you remove a broke bolt?

Insert small bar having enough length in contact with bolt and then do stud arc-welding between bar & bolt.Then turn it as per thread direction.Thus we can remove broke bolt.

Read more

How expensive is it to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

Diagram for changing the serpentine belt?

As you listed no make, model, engine, or year, all I can say is look under the hood for a placard diagram. Usually there is one there.

Read more

What causes the serpentine belt to break?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).Squealing sound: Belt slipping.

Read more

How do you replace the serpentine belt on a 1997 grand prix and there is apparently two designs of the 3.8 V6. so how do you know which design your motor is so that you order the right drivebelt?

The 3.8 could be factory supercharged or not. If it was supercharged it would be obvious.I don't know anything about two designs, i know there is a 3.1 and a 3.8 liter v6. in my 97,3.8 v6 there is a tension pulley, this pulley only puts tension on the belt so it stays on. use a big wrench to pull...

Read more

There is a wheel at the top of the serpentine belt that you cant seem to get the belt over you have the belt assembled but you cant get pat this part HELP?

you need to loosen the tensioner.. ist like a small wheel with some sort of spring attatched..

Read more

What is the purpose of a serpentine belt?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

What are the signs of a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

Can I drive without a serpentine belt?

As you can see, driving without a serpentine belt is not an option, at least not for very long.*Some cars have an electric water pump and/or electric assist steering.

Read more

Why does the car die when you unhook the battery on 2000 alero?

You probably have a failing alternator.

Read more

How do you get the tensioner to move on 1988 caravan to replace serpentine belt having a diffucut time trying to get belt on?

You don't mention which engine but on my 90 3.3 I put a wrench on it and just move it. It's kinda hard.

Read more

What happens when the serpentine belt breaks on a car?

when serpentine belt breaks alternator and water pump stop working along with power steering pump

Read more

How do you claim the law suit against the repair job that caused the truck broke down?

To claim in a lawsuit that a previous repair caused a further breakdown you need to:1st Detail the break down and the damage it caused. Courts only deal in $ amounts, so you will need to do some math.2nd Prove there was a previous repair done.3rd Conect the failure to the repair, usually you will...

Read more

Do you have a Diagram of serpentine belt for 94 ranger 3.0?

check on autozone .com or maybe going to your local store and they might have one or be able to help you with it

Read more

How many miles can you get out of a serpentine belt?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

How do figure out when to change the serpentine belt in 2001 Toyota corolla car?

Look at the belt. If it's shows signs of being frayed on the edges, or if it looks dry and cracked by the inner ribs, or if you hear a squeeling sound when you accelerate, or if you have more than a 1/4 inch play (push your finger on the belt), it's time to change your belt.

Read more

Why cant you detension the serpentine belt tentioner the bolt keeps rotating and not letting you get the belt on?

because the bolt is striped or you pulley is no bad take it off and get another one

Read more

Do I need to replace my serpentine belt?

Most serpentine belts generally last between 50,000 and 100,000 miles.Eventually, your car's serpentine belt will wear down from continuous exposure to heat and friction and will need to be replaced.

Read more

How to fix Engine that won't restart?

Life experience has given me this info. It could be a hand full of things, but without seeing/hearing our car I can only venture guesses.If you turn the key and...you hear a click but theres no movement after, its more than likely the starter motor, it could also be the relay that connects your s...

Read more

Can buy a serpentine belt for 1996 3.1 liter V.s Pontiac grand that bypasses the AC compressor?

Go to any auto parts store and see if Pontiac sold a 1963 Model with the 3.1 V6 without an air conditioner. If not a belt from any GM model equipped without A/C and the 3.1 V6 should work.

Read more

What is the difference between a serpentine belt and an accessory belt?

An accessory belt is any belt that drives additional power systems from the front crank of an engine. Typically, these "accessories" are the alternator, power steering pump, and air conditioning compressor. In many rear wheel drive vehicles, a belt is also used to drive the radiator fan. Typicall...

Read more

How do you change the timing belt for 2000 Mazda Protege?

YOU DON'T WANT TO TRY THIS BY YOURSLF IF YOU HAVE NEVER DONE THIS BEFORE

Read more

How do you release the belt on 2000 model gu patrol to remove alternator?

Loosen the tensioner pulley. The tensioner pulley will slide to the right. This will loosen the alternator belt. So it can be removed.

Read more

How long does it take to replace serpentine belt?

How Long Does It take To Replace A Serpentine Belt? For professional automotive technicians with the right tools and training the replacement of a serpentine belt usually takes about 30 min to an hour.This time varies by the make, model, and year of vehicle that you're driving as some take longer...

Read more

How do you restart window washer syphon?

Automotive window washer systems are self priming. Assuming the reservoir is full, you may have a bad pump, cracked/pinched hoses or plugged nozzles.

Read more

How do you restart dead Merc E200?

You get a small african swallow and place its foot inside the ignition, after about five minutes turn the ignition, you'll be fine :)

Read more

What is a serpentine belt in a car?

A rubber belt that goes around all pulleys & has idlers as tensioners. On cars there are either v belts (belts shaped like a "v" that are tightened by moving accessories) or serpentine, which is usually one ribbed belt with idlers.

Read more

How do you take find out how to put on a serpentine belt for a 3.3L V6 if you dont have the diagram on the van anymore or the original belt?

you don't say wot make an model... so i presume its the Chrysler new yorker as i cant think of another with a 3.3 v6.. easy answer.. buy a haynes manual.. if your gonna replace the belt.. you might as well do other stuff like replace the water pump and front engine seal while your at it..

Read more

Need to find out how to replace serpentine belt?

Just pry the belt tensioner back and remove the old belt, and install a new one.

Read more

Can you get a 2000 Oldsmobile Alero owners manual from a dealership?

Generally not. Your best bet would be go to a wrecking yard.

Read more

What would cause a serpentine belt to squeal?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).Squealing sound: Belt slipping.

Read more

What does a bad serpentine belt look like?

The symptoms of a loose serpentine belt include a loud squealing noise when the engine is started or when the steering is turned all the way to one side.A serpentine belt that keeps slipping off the pulley is another symptom of a bad tensioner.

Read more

What causes a serpentine belt to slip off?

Slipping can be the result of a loss of belt tension (or a weak automatic tensioner) or pulley misalignment.When the belt slips off the track, the friction between the belt and accessory drive pulleys causes the belt to overheat.If you hear a high pitched squealing noise, it's probably time for a...

Read more

What are signs of a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

What causes a serpentine belt to come off?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).

Read more

What is the transmission fluid capacity of a 2000 Oldsmobile Alero 3.4L?

To keep a car running its best, a person has to keep the fluid levels maintained. The 2000 Oldsmobile Alero uses 12 quarts of transmission fluid.Ê

Read more

What happens if a serpentine belt breaks while driving?

A broken serpentine belt leads to a sudden loss of power assist for the steering system, where the steering wheel all-of-a-sudden becomes very hard to turn.A broken serpentine belt stops the water pump from circulating coolant (antifreeze) through the cooling system, and the engine can overheat -...

Read more

How do you move a broke down bobcat?

you need a rollback tow truck and winch it on to itif the bobcat is broken down, then that will not work. I have the same problem. Everything being hydraulic the tracks wont move unless the machine is running. There aren't too many machines that can pull that much dead weight. There has to be a w...

Read more

Where can you obtain a serpentine belt diagram for a 1993 VW?

Go to your closest Autozone and they can print you one out.

Read more