How do you replace the serpentine belt on a 1993 Mercury Cougar?

Cars & Vehicles
Serpentine Belts
Mercury Cougar

To remove the serpenteen belt on this vehicle, you must first locate the spring loaded tensioner. You will need a 1/2" breaker bar or a socket to recoil the spring load. doing this will release the tension on the belt. You can then remove the belt.

NOTE: If you are just changing the belt with a new one, DO NOT remove the tool until the new belt is in place. You should not have to remove any parts to change the belt.

Previous questionWhat kind of skills you need to be a Auto technician?
Next questionHow the moon has been studied and explored?

Related question

How do you change the serpentine belt on a 1994 mercury cougar xr7?

with a 1/2" rachet or breaker bar placed in the square whole on the tensioner pully, you push (from passenger side to drivers) which will release the presure on the belt. Might want to draw a "map" of how the belt goes cause it ain't obvious when its off the car.

Read more

How do you release serpentine belt on a 89 Mercury Cougar?

You have to release your tensioners in order to release your serpentine belt. When you put the belt back on you have to follow the diagram on the hood of your car.

Read more

How do you replace serpentine belt on a fx 35?

1. Remove front engine undercover.2. Loosen idler pulley (alternator and power steering oil pump belt) lock nut and adjust tension by turning bolt.3. Same is done for the other idlery pulley (A/C compressor belt).

Read more

How do you replace serpentine belt on 2005 Equinox?

Begin by loosening the tensioner pulley on your 2005 Chevrolet Equinox. The serpentine belt will become loose and can be removed. Reverse the process to install your new serpentine belt.

Read more

How do you disable the door-adjar chime in a 1993 mercury cougar?

It should be located under the dashboard. usually behind the center console (heater controls, stereo etc...) You should be able to just pull out the wire that is fitted into it. But be careful. The same chime is used to let you know if you've left your headlights on, or your keys in the ignition.

Read more

How do you replace the glass on the driver side power mirror 1999 mercury cougar?

the mirror should just pop out, remove the two heating wires and install the new mirror

Read more

How do you replace an ignition switch on a 1987 Mercury Cougar?

The ignition switch is located on the bottom of the steering column. Take out the 4-6 screws that hold the bottom piece and you will see the switch should be about 3-4 inches long held in place by 2 screws. take black plug off then replace switch plug back in and there you go.

Read more

How do you replace lower ball joint on 93 Mercury Cougar?

Remove the tire and wheel from your 1993 Mercury Cougar. Remove the ball joint retaining nut. Pound the ball joint out with a hammer. Reverse the process to install your new ball joint.

Read more

How do you reset computer on a 1989 Mercury Cougar?

Disconnect the vehicles battery. Leave it unhooked for several hours. Reconnect the battery. This should reset the 1989 cougars computer.

Read more

How do you replace a serpentine belt on a 1995 Chevrolet Camero?

Replacing the serpentine belt on both V6 & V8 rear drive engine are fairly easy than front wheel drive. The belt is located just between the front of the engine and the radiator. You have plenty of clearance to work. Just need to losen the tension and the belt should come out. Putting the new...

Read more

Can you replace a serpentine belt yourself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

How do you change a serpentine belt?

How to Replace a Serpentine Belt Take a good look at both your repair manual and your belt routing diagram under the hood before beginning. Look at the way the old belt wraps around the pulleys. Locate the self-adjusting tensioner and know that you need to be careful when releasing tension ...

Read more

How do you change the tire 99 mercury cougar?

Replacing the tire on a 99 mercury cougar is fairly easy. Jack up the car, remove the rim bolts and the tire will come off. Put on new one and reassemble.

Read more

How do you flush a 1995 Mercury Cougar?

Flush the cooling system? Flush the fuel system? Flush the hydraulic brake system? Flush the AC system? Flush the transmission? Pick one.

Read more

How do you remove serpentine belt on 2005 Chevy Cobalt?

You have to release the stress in the tensioners to remove the serpentine belt. When you put it back on there is a diagram under the hood of the car that takes you step by step.

Read more

How much does it cost to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How do you get the tensioner to move on 1988 caravan to replace serpentine belt having a diffucut time trying to get belt on?

You don't mention which engine but on my 90 3.3 I put a wrench on it and just move it. It's kinda hard.

Read more

How much does it cost to replace the serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How often does a serpentine belt need to be replaced?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

How expensive is it to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

Do you have a diagram of how to put the serpentine belt on the pulley?

You may get an answer if you list the vehicle & engine you are talking about. You are not going to get an answer to this question as is.

Read more

How do you replace the motor mount on a 2000 merury cougar v6?

Dont replace it just get rid of the car all together. I have one now that i have owned for the past 4 years and its been nothing but problems. Id bet the reason they stopped making the cougar in 02 was because of so many issues. if you have a manual trans get rid of it now. they are the most prob...

Read more

Where can you obtain a serpentine belt diagram for a 1993 VW?

Go to your closest Autozone and they can print you one out.

Read more

How do you repair the serpentine belt on a 1998 Mitsubishi Galant?

You don't repair a serpentine belt. You replace the worn or broken belt with a new one.

Read more

Do I need to replace my serpentine belt?

Most serpentine belts generally last between 50,000 and 100,000 miles.Eventually, your car's serpentine belt will wear down from continuous exposure to heat and friction and will need to be replaced.

Read more

1999 mercury grand marquis 4.6 serpentine belt routing?

The 1999 Mercury Grand Marquis has (2) TWO engine styles, both different. The style for Vin numbers with a "W" engine, and the Vin numbers with an "X".The "W" series has the A/C Compressor to the RIGHT of the engine when viewed from the front.The belt circles all components from the outside but t...

Read more

Can I replace serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How do you tighten the serpentine belt on a 1997 Saturn?

You don't. The belt tension is automatically adjusted via a spring loaded tensioner. If the serpentine belt is noisy or worn out prematurely. replace the tensioner. The belt should be inspected for cracks and other signs of wear. Replace worn out belt(s) before they break leaving you stranded.

Read more

How do you remove the headlights' covers of a 1999 Mercury Cougar?

There aren't covers per se, but if yours are cloudy/foggy, you can fix them yourself with an hour of your time and around $20. They will look better, and more importantly, you will see better at night.

Read more

How do you get the accessory drive belt or serpentine belt off of a 1989 sunbird?

To remove the accessory drive belt or the serpentine belt from the motor on a 1989 Sunbird, it is necessary to loosen the belt tensioner. Look for a pulley that has a bolt in a slot. Loosen the bolt and move the tensioner so there is a gap in the belt. Then remove the belt from each pulley.

Read more

Does Jiffy Lube replace serpentine belts?

The serpentine belt! For this key component, rely on the Jiffy Lube® serpentine belt replacement to help keep your vehicle on the road.

Read more

Where could you find an illustration on replacing serpentine belt on '97 Buick Park Avenue?

There should be an illustration in your ownners manual.Just had mine done.. mechanic had to remove psgr side motor mount to release belt. Not a fun job.trust me this ne job you want to pay someone to do, you need to lower the engine cradle to remover the PS motor mount,you could also visithttp://...

Read more

How long does it take to replace serpentine belt?

How Long Does It take To Replace A Serpentine Belt? For professional automotive technicians with the right tools and training the replacement of a serpentine belt usually takes about 30 min to an hour.This time varies by the make, model, and year of vehicle that you're driving as some take longer...

Read more

When should I replace my serpentine belt?

Under normal conditions, the belt needs to be replaced every 4 to 6 years.However, those living in areas where the temperature and humidity can vary greatly throughout the year may need to change it more frequently.

Read more

How do you align a serpentine belt pulley?

Read more

How do you replace belt on ls1?

Pardon me but what is an Is1?

Read more

Where is the thermostat located on a 2002 mercury cougar?

Should be in a removable housing at the engine end of the upper radiator hose

Read more

Where is the fuel pump on a 1999 Mercury Cougar?

On a 1999 Mercury Cougar :The ELECTRIC fuel pump is INSIDE the fuel tankIt is installed through an access hole in the top of the fuel tank

Read more

Need to find out how to replace serpentine belt?

Just pry the belt tensioner back and remove the old belt, and install a new one.

Read more

How do you change a serpentine belt on a Chevy Silverado?

Shop Products Familiarize yourself with the belt routing diagram.Insert a 3/8 inch drive ratchet into the belt tensioner.Pull the tensioner counterclockwise to loosen the belt.Pull the belt off the idler pulley.Release the tensioner.Pull the belt off and out.

Read more

How do you change a serpentine belt on a 2001 Chevy Suburban?

Read more

How do you change a serpentine belt on a 2001 Chrysler Town and Country?

How to Replace the Serpentine Belt in a Chrysler Town & Country Open the hood and find the belt tensioner pulley. Look at how the belt is routed around various pulleys. Use a wrench to rotate the belt tensioner pulley bolt and slide the old belt off of the tensioner pulley. Make sure y...

Read more

How do you change a serpentine belt on a 2008 Toyota Corolla?

Read more

How do you do you find the serpentine belt diagram for a Toyota RAV4 2001?

There should be a diagram under the hood somewhere. Normally on the fan shroud. Click the link for a diagram. If you do not see one search with the term "2001 Toyota Rav 4 belt diagram" and you will find a diagram.

Read more

How do you install a serpentine belt on a 99 Isuzu Rodeo?

There is a belt tensioner (spring loaded pulley that automatically keeps the belt tight) that needs to be temporarily slackened while the now loose belt is slipped off one of the accessories. Sorry, but I can't remember what tool is needed to loosen the belt tensioner. Just opening the hood and o...

Read more

How do you change a serpentine belt on a Mazda 3?

How to Replace a Mazda 3 Serpentine Belt Open the Mazda 3's hood and support it with the prop rod. Connect the belt-tensioner tool into serpentine belt tensioner and move the tensioner pulley away from the belt with the tool. Pull the belt off the engine accessory pulleys by hand. Stretch ...

Read more

What is the cost to replace serpentine belt?

It is very inexpensive to replace a serpentine belt.The replacement cost is only going to be between $90 and $200 in most cases.The belt itself will cost between $25 and $75 while the labor costs will probably be between $75 and $120.

Read more

Where do you hook an OBD code reader on a 1997 Mercury Cougar?

passenger side panel, above left knee

Read more

How do you tighten serpentine belt on 1993 Ford F-350 7.3l diesel so my power brakes will work again creating the nescessary vacuum?

7.3l diesel does not have an adjusment for the serpentine beltit is autmatically adjusted with the belt tensioner.if the tensioner is not keeping belt tight, replace the belt and check to see that tensioner is working correctly.most times if vaccuum pump is not working the power brakes, you need ...

Read more

How do you adjust serpentine belt on a 1999 Holden jackaroo?

On all U.S. vehicles that use A single serpentene the belt has an automatic tensioner. I suspect that your can does too. It could be stuck.

Read more

How can you bypass a serpentine belt on a 2002 converible sebring from the ac compressor?

You realy can't. If your intention is not to power the A/C unplug the wire that connects to the electric clutch. It should be right behind the pully.

Read more

How do you replace Brake line on 1996 Mercury Sable?

Some knowledge of brake repair and procedures is necessary to complete this job for proper and safe brake operation results. Your local auto parts store can supply you with the parts needed. Have a trusted mechanic coach you and inspect the job when finished.

Read more

Do you losen the altinator to change serpentine belt on a 94 Jimmy?

You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.

Read more

How do you replace front fenders on 1993 S10 blazer?

To replace the front fenders on a 1993 S10 Blazer, unscrew the bolts holding the old fenders in place. There are also rivets that have to be removed around the wheel well on both sides. The bolts are located inside the hood area on top of the fender.

Read more

What happens if you put a serpentine belt on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

How do you stop serpentine belt from squeeking?

Replace belt and check all pulleys for wear or rough spot

Read more

How do you replace the front brake pads on a 1999 Mercury Mountaineer?

Lift the car, remove the tire, remove the brake shoe/caliper, and remove the old brake pads. Put in the new brake pads, replace the brake shoe/caliper, replace the tire, and lower the car.

Read more

How do you replace the cabin air filter on a 2002 mercury sable?

Purchase a Purolator Cabin Filter. It comes with complete instructions.

Read more

How do you fix a 1991 Mercury Cougar ls that somkes?

Depends on the color of the smoke. White Smoke = Coolant entering the combustion chamber. Normally caused by a blown head gasket or cracked head. Black Smoke = Overly rich fuel/air mixture. Blue Smoke = Engine burning oil. Worn or broken rings.

Read more

How long do BMW serpentine belts last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

Can you put a serpentine belt on backwards?

you actually can put a belt on backwards.grooves go to grooves, and smooth goes to smooth.but you have to pay close attention to the belt routing diagram.if the belt is put on the wrong way it can spin the water pump reversed causing an overheat condition very fast after starting.

Read more

How do you replace the fuel pump on a 1993 Ford Tempo?

located in the fuel tank probably have to remove for access

Read more

What is the Firing orders on 1996 Mercury Cougar 4.6L?

The firing order of the 1996 Mercury Cougar is 1, 3, 7, 2, 6, 5, 4, 8. This is for the 4.6 Liter engine.

Read more

Does the radiator on a 1999 Mercury Cougar have a cap actually on the radiator itself?

No, it has no cap on radiator. You fill radiator thru the reservoir cap on the rt side of engine. Hope this helps.

Read more

What does the Code p0401 mean on 1999 Mercury Cougar?

It means there is insufficient flow within your EGR (Exhaust Gas Recirculation) system.While it could be a faulty component such as the dfpe sensor, the EGR solenoid or the EGR valve itself it is most often clogged passages. These are between the throttle body and the intake manifold (under the g...

Read more

How do you reroute serpentine belt to bypass ac compressor on 1995 town car?

If that model was available without a/c, you will need to purchase the belt for a 95 town car w/out ac, and follow the appropriate belt routing diagram for that model.

Read more

How do you remove the radiator in a 1993 mercury topaz 6-cylinder?

# Disconnect the negative battery cable # Drain cooling system # If equipped remove the plastic shield over the radiator # Disconnect the electric cooling fan motor wires and A/C discharge lines if equipped # Disconnect the overflow hose from the radiator filler neck # Remove the upper hose from ...

Read more

How do you replace the fuel filter on a 1993 Ford F-150?

You'll need a special tool (available at a parts store) to take off the filter. The tool releases the filter from the fuel line fittings. Sometimes it's easy to take off the filter and sometimes it difficult. Needle nose pliers won't work.

Read more

What does a serpentine belt do?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

How to remove the drivers side door panel on a 1989 mercury cougar?

Take out all screws that hold the trim and the panel that holds the power switches. Remove the panel that holds the swithches and take out the screws that remain. there is also a screw down next to the light at the bottom of the door. once all screws are out, lift up on the panel and it will slid...

Read more

How do you install serpentine belt on 88 Chevy silverado 4x4 350 auto?

Loosen tensioner and follow label (under hood) for routing

Read more

How much does it cost to replace a pulley and serpentine belt?

It is very inexpensive to replace a serpentine belt.The replacement cost is only going to be between $90 and $200 in most cases.The belt itself will cost between $25 and $75 while the labor costs will probably be between $75 and $120.Taxes and fees will be added onto these prices too.

Read more

How do you change the serpentine belt on a 2002 Chrysler town and country mini-van 3.8 engine?

There should be an idler pulley that you need to loosen to take belt off, draw a diagram of how the belt looks before you take it off so you can see how it goes back on.

Read more

How do you restart a 2000 alero that broke the serpentine belt?

Serpentine belts don't just break. There is probably an accessory that is locked up such as the alternator or a idler pulley. Check each pulley that the belts contacts and make necessary repairs before installing a new belt. Once you have done that just start the engine back up as you normally wo...

Read more

How do you replace timing belt on 1999 Kia Sportage?

You should be able to find a shop manual for this at the local library...make copies of the right pages...good luck:)

Read more

How do you replace alternator belt on 99 eclipse?

Begin by loosening the tensioner pulley on your 1999 Mitsubishi Eclipse. The alternator belt will become loose and can be removed. Put the new alternator belt on and tighten the tensioner pulley.

Read more

When was the last Mercury Cougar made?

Introduced on September 30, 1966, the final Cougar rolled off the assembly line on August 2, 2002.In honor of the half century that's passed since the Cougar's debut, here's a look back at its origins.1967 Mercury Cougar Dan Gurney Edition.

Read more

What happens when the serpentine belt breaks on a car?

when serpentine belt breaks alternator and water pump stop working along with power steering pump

Read more

Is a serpentine belt the same as a timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

How do you replace timing belt on seat leon 1.9tdi?

Replacing the timing belt is a very detailed task. It will include removing the engine. Timing belt replacement directions can be obtained from most auto-parts stores.

Read more

Which pully do you loosen to change the belt on a 1993 GMC Sonoma?

Look for the idler pully,it will be the one that runs against the back of your surpentine belt,It is spring loaded,it is smooth,use a breaker bar or 1/2 drive ratchet,there is a bolt head that sticks out of the front of the pulley find a socket that fits this bolt head it should be metric,make su...

Read more

How do you replace timing belt on 95 avenger?

In order to replace your timing belt on your 1994 Avenger, you will need to first drain your cooling system. Remove the timing belt and mounting bolts and replace with your new belt.

Read more

How much is a 1967 Mercury Cougar worth?

**Figure based on a stock 1967 Mercury Cougar valued at $12,600 with OH rates with $100/300K liability/UM/UIM limits.Actual costs vary depending on the coverage selected, vehicle condition, state and other factors.

Read more

Where is distributor located on 99 Mercury Cougar?

It doesn't have a distributor. It has a DIS, (Distributorless Ignition System).

Read more

How to replace motor mount rear right-passenger sideattached to the crossmember on 1993 Mercury Villager GS?

There is no special procedure, this is just a difficult one to do. Unbolt it, jack up the engine, then spend an hour or two grunting and getting cut up maneuvering it out and the new one in. It may (but not so much as I recall) help to loosen the other mounts.

Read more

Where is the fuel pump on a 1993 mercury capri?

in the fuel tankunder the back seat. take out the back seat it just pops up and out and t is right there easy as pie to get to.

Read more

What will make the charging system come on on a 2000 Mercury Cougar?

The charging system is the alternator which is on and functioning anytime the engine is running. If not, then you have a problem with the alternator.

Read more

How important is a serpentine belt?

Well, it won't keep your pants up, but it does transport power to your vital automotive components.The serpentine belt is one long, snaking, winding belt that keeps your alternator, power steering pump, air conditioning and — in some cases — your water pump running smoothly and effectively.

Read more

How do you replace the serpentine belt on a 1997 grand prix and there is apparently two designs of the 3.8 V6. so how do you know which design your motor is so that you order the right drivebelt?

The 3.8 could be factory supercharged or not. If it was supercharged it would be obvious.I don't know anything about two designs, i know there is a 3.1 and a 3.8 liter v6. in my 97,3.8 v6 there is a tension pulley, this pulley only puts tension on the belt so it stays on. use a big wrench to pull...

Read more

How do you replace a window motor on a 1993 GMC Jimmy?

Disconnect the battery, Remove the door panel, vapor barrier plastic, power window connections, and I would remove the entire regulator assembly with motor attached. It helps to have someone hold the window as it drops inside of the door. Some motors are riveted to the regulator at the factory, s...

Read more

Where is the automatic transmission pan located on a 2001 Mercury Cougar v6?

On the bottom of the transmission.

Read more

Where is the ERG valve located on 1993 GMC Jimmy and how do you replace it?

Assuming 5.7 V8, it's on the passenger side, a few inches to the side of the throttle body.

Read more

How do you replace front driver side turn signal bulb on a 2000 Mercury Mystique?

2000 Mercury Mystique turn signal light bulb lamp replacement procedure: Purchase the correct replacement turn signal light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information and full light bulb part numbers list. Then consult you...

Read more

How do you replace a coil pack on a 1993 bonnville?

the coil packs on a Bonneville are located on the right side of the front valve cover. first you need to find which coil has failed there are 3, once you find that out it is as simple as taking off the plug wires and removing the 2 screws and pulling straight up.

Read more

How do you replace the timing belt on a 2009 Santa Fe?

If you have the 3.3 V6 engine it doesn't use a timing belt. It has a chain which requires no maintenance.

Read more

How do you replace the ac belt on a 95 truck?

You actually expect to get an answer. Would that be a Ford, Chevy, GMC, Dodge, Toyota, Nissan, or any other of the makes of trucks out there?

Read more

How do you replace the Timing Belt on a 1994 Ford Aerostar 3.0L?

There isn't a timing belt on the 3.0. This engine has a timing chain which would require extensive work in the removal of parts. You don't have to remove the radiator but will have to remove all of the front of the engine accessories on the front of the engine to get to the timing chain. Not an e...

Read more

How do you replace the two belts on a 1999 pick up 5 something v8?

You don't list the Make, Model, which belts, or engine size, and expect an answer. The only answer I can provide with the information you provided, is, take it to a professional for this repair.

Read more

How do you repair ac compressor belt 1993 j 30?

if your talking about the serpentine, you buy a new one

Read more