How do you remove serpentine belt on 2005 Chevy Cobalt?

Cars & Vehicles
Chevy Cobalt

You have to release the stress in the tensioners to remove the serpentine belt. When you put it back on there is a diagram under the hood of the car that takes you step by step.

Previous questionWhat is the oil capacity for a Yamaha roadstar?
Next questionHow do you change the R12 to 134 in a 1993 Chevy silverado?

Related question

How do you replace serpentine belt on 2005 Equinox?

Begin by loosening the tensioner pulley on your 2005 Chevrolet Equinox. The serpentine belt will become loose and can be removed. Reverse the process to install your new serpentine belt.

Read more

How do you hotwire a 2005 Chevy cobalt videos?

This is a question whose answer could potentially be used for the commission of illegals. As such, we can't answer it here.

Read more

How do you change a serpentine belt on a Chevy Silverado?

Shop Products Familiarize yourself with the belt routing diagram.Insert a 3/8 inch drive ratchet into the belt tensioner.Pull the tensioner counterclockwise to loosen the belt.Pull the belt off the idler pulley.Release the tensioner.Pull the belt off and out.

Read more

How do you install serpentine belt on 88 Chevy silverado 4x4 350 auto?

Loosen tensioner and follow label (under hood) for routing

Read more

How do you change a serpentine belt on a 2001 Chevy Suburban?

Read more

Where is the oil drain plug on 2005 Chevy Cobalt?

Underneath the car's engine behind the motor mount.

Read more

How do you fix a Short in dome light 2005 Chevy Cobalt?

I think the short is located in the power control module

Read more

What do the 2005 Chevy Cobalt dash lights mean?

It depends on which light is being discussed. They are generally used in order to alert you to a problem with the vehicle so you can get it fixed.

Read more

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

How to remove the door panel in 2006 Chevy Cobalt?

first you have to remove the part where the mirror is adjusted on the inside, it snaps off with 3 clips. You can stick a screwdriver under there wrapped in a little duct tape to keep it from scratching the door. After you do that, you have to remove the clips from the door handle in the middle an...

Read more

How do you replace serpentine belt on a fx 35?

1. Remove front engine undercover.2. Loosen idler pulley (alternator and power steering oil pump belt) lock nut and adjust tension by turning bolt.3. Same is done for the other idlery pulley (A/C compressor belt).

Read more

Can a 2.2 Liter 2005 Chevy Cobalt engine be put into a 2005 Chevy Equinox?

No, the engines are completely different.

Read more

How do you change a serpentine belt?

How to Replace a Serpentine Belt Take a good look at both your repair manual and your belt routing diagram under the hood before beginning. Look at the way the old belt wraps around the pulleys. Locate the self-adjusting tensioner and know that you need to be careful when releasing tension ...

Read more

Where is the solenoid in a 2005 Chevy cobalt?

It has many solenoids. Need to know which one you are referring to.

Read more

How do you put brake fluid in a Chevy Cobalt?

Add Brake Fluid: 2005-2010 Chevrolet Cobalt Getting Started.Open the Hood.Find Reservoir. Locate the brake fluid reservoir and clean it.Check Level. Determine the brake fluid level.Add Fluid. Determine brake fluid type and add fluid properly.Replace Cap. Secure the brake fluid cap onto the re...

Read more

How do you disable key chime on a 2005 Chevy?

http://www.silveradoss.com/forums/index.php?showtopic=3033

Read more

How do you stop serpentine belt from squeeking?

Replace belt and check all pulleys for wear or rough spot

Read more

How do you align a serpentine belt pulley?

Read more

How do you program keyless remote for 06 Chevy Cobalt?

This vehicle requires a scan tool to program the remote, a dealer or locksmith will have to do it.

Read more

How long do BMW serpentine belts last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

How do you remove serpintene belt on 98 Ford truck?

The tensioner has an arm with a roller at the bottom. Find the size of the socket required to get around the nut at the center of the roller (I believe the last Ford I did this on required a 16mm socket). Turn the ratchet/breaker bar (attached to the socket) counterclockwise. The arm should turn ...

Read more

How do you install halo headlights on a 2007 Chevy Cobalt?

full instructions as to how to install cobalt halo projector headlights.

Read more

How do you reroute serpentine belt to bypass ac compressor on 1995 town car?

If that model was available without a/c, you will need to purchase the belt for a 95 town car w/out ac, and follow the appropriate belt routing diagram for that model.

Read more

How do you fix seat belt on Chevy tracker?

You start by identifying what's wrong with it. Chances are, it's going to be something you'll simply replace.

Read more

How do you change the serpentine belt on a 1994 mercury cougar xr7?

with a 1/2" rachet or breaker bar placed in the square whole on the tensioner pully, you push (from passenger side to drivers) which will release the presure on the belt. Might want to draw a "map" of how the belt goes cause it ain't obvious when its off the car.

Read more

Do you have a diagram of how to put the serpentine belt on the pulley?

You may get an answer if you list the vehicle & engine you are talking about. You are not going to get an answer to this question as is.

Read more

How do you replace a serpentine belt on a 1995 Chevrolet Camero?

Replacing the serpentine belt on both V6 & V8 rear drive engine are fairly easy than front wheel drive. The belt is located just between the front of the engine and the radiator. You have plenty of clearance to work. Just need to losen the tension and the belt should come out. Putting the new...

Read more

How do you repair the serpentine belt on a 1998 Mitsubishi Galant?

You don't repair a serpentine belt. You replace the worn or broken belt with a new one.

Read more

How do you release serpentine belt on a 89 Mercury Cougar?

You have to release your tensioners in order to release your serpentine belt. When you put the belt back on you have to follow the diagram on the hood of your car.

Read more

How do you change a serpentine belt on a 2001 Chrysler Town and Country?

How to Replace the Serpentine Belt in a Chrysler Town & Country Open the hood and find the belt tensioner pulley. Look at how the belt is routed around various pulleys. Use a wrench to rotate the belt tensioner pulley bolt and slide the old belt off of the tensioner pulley. Make sure y...

Read more

How do you replace the serpentine belt on a 1993 Mercury Cougar?

To remove the serpenteen belt on this vehicle, you must first locate the spring loaded tensioner. You will need a 1/2" breaker bar or a socket to recoil the spring load. doing this will release the tension on the belt. You can then remove the belt.NOTE: If you are just changing the belt with a ne...

Read more

How do you change a serpentine belt on a 2008 Toyota Corolla?

Read more

How do you remove console on ChevyS-10 2001?

How to remove center console 2001 chevy s-10

Read more

How do you adjust serpentine belt on a 1999 Holden jackaroo?

On all U.S. vehicles that use A single serpentene the belt has an automatic tensioner. I suspect that your can does too. It could be stuck.

Read more

How do you install a serpentine belt on a 99 Isuzu Rodeo?

There is a belt tensioner (spring loaded pulley that automatically keeps the belt tight) that needs to be temporarily slackened while the now loose belt is slipped off one of the accessories. Sorry, but I can't remember what tool is needed to loosen the belt tensioner. Just opening the hood and o...

Read more

How do you tighten the serpentine belt on a 1997 Saturn?

You don't. The belt tension is automatically adjusted via a spring loaded tensioner. If the serpentine belt is noisy or worn out prematurely. replace the tensioner. The belt should be inspected for cracks and other signs of wear. Replace worn out belt(s) before they break leaving you stranded.

Read more

How do you change a serpentine belt on a Mazda 3?

How to Replace a Mazda 3 Serpentine Belt Open the Mazda 3's hood and support it with the prop rod. Connect the belt-tensioner tool into serpentine belt tensioner and move the tensioner pulley away from the belt with the tool. Pull the belt off the engine accessory pulleys by hand. Stretch ...

Read more

How do you reset the tire pressure sensor on a 2008 Chevy Cobalt?

Read more

How do you get the accessory drive belt or serpentine belt off of a 1989 sunbird?

To remove the accessory drive belt or the serpentine belt from the motor on a 1989 Sunbird, it is necessary to loosen the belt tensioner. Look for a pulley that has a bolt in a slot. Loosen the bolt and move the tensioner so there is a gap in the belt. Then remove the belt from each pulley.

Read more

Where is the tensioner pulley to tighten the serpentine belt on a 2000 Chevy Silverado?

If you're standing at the front of the truck and looking into the engine compartment the tension pulley is on the left side about half way down.

Read more

What happens if you put a serpentine belt on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

Can you put a serpentine belt on backwards?

you actually can put a belt on backwards.grooves go to grooves, and smooth goes to smooth.but you have to pay close attention to the belt routing diagram.if the belt is put on the wrong way it can spin the water pump reversed causing an overheat condition very fast after starting.

Read more

How do you do you find the serpentine belt diagram for a Toyota RAV4 2001?

There should be a diagram under the hood somewhere. Normally on the fan shroud. Click the link for a diagram. If you do not see one search with the term "2001 Toyota Rav 4 belt diagram" and you will find a diagram.

Read more

Is ok to drive your 2005 Chevy cobalt with only 3 of the 4 lug nuts?

Drive it to the nearest garage for repair and stay off the highways.

Read more

How do you remove freeze plug Chevy?

Punch a hole in the middle of the pug and pry hard it can take a lot.

Read more

How do you remove commadore 2005 drivers seat?

there are bolts that are underniether the seat which you need to use a ratchet to take the seats out its held in by four bolts i believe

Read more

How do you remove replace 2005 sts cabin filter?

you dump the old one in the trash then you go to the store and by a new one dweeb leed lame insane poop

Read more

What tool do you use to remove seat belt from 96 Chevy cavaliar?

Most seat belts are bolted to the floor with a large Torx bit headed bolt. I think the size is a T50. Individual Torx sockets are available at Sears, Autozone etc . for about $5 each.

Read more

Can you replace a serpentine belt yourself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

What does a serpentine belt do?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

How do you disable the passenger seat belt alarm on a 2005 Toyota Camry le?

Normally there is a wire which runs down inside the plastic sleve which is around the lower part of the seat belt mech..the plastic will most likely be the same color as the plastic where the seat belt clips to ,,cutting this wire should shut it up ..the alarms shuts up when the seat belt is clip...

Read more

Do you losen the altinator to change serpentine belt on a 94 Jimmy?

You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.

Read more

How do you check your cmp sensor 2005 Chevy uplander?

If you suspect a failing sensor you probably see it is acting up only at certain times. CMP usually under high heat stress to start.It will either fail or not and the scanner operator will see it.

Read more

How do you remove the passenger door sail panel on your 2005 F-150?

first you can try to take it off your best or you can call a mechanic to help you. It would only cost about $20.00 to $50.00 or sometimes you could get it off for free!

Read more

How do you remove the door handle on a 2005 Kia Spectra?

which door, most of the time you remove the door panel screws and then pull hard you will not brake it if you pull and look you can see plastic keepers attaching the door panel they will pull out but feel like you will brake something, then remove clear plastic car full not to tare then use a fla...

Read more

Can you drive without serpentine belt?

Since the serpentine belt is generally the only accessory drive belt on vehicles these days, this is what you'll lose: Engine cooling* - The serpentine belt drives the water pump.Without the water pump, there will be insufficient coolant flow to maintain engine temperature, and you will overheat ...

Read more

How do you remove heat shield on 2005 sunfire to lower gas tank?

The heat shield on a 2005 Sunfire can be removed by taking out the retaining bolts. The gas tank can then be lowered from the vehicle.

Read more

How do you bleed the brakes on a 2005 Chevy Colorado?

The same procedure as bleeding any other vehicle unless you have taken the ABS/Traction Control Module off and apart. In which case you would need special expensive equipment to bleed the module of air.

Read more

How do you change the oil on a 2005 Chevy Equinox?

Oil & Filter Change Chevrolet Equinox (2005-2009) Getting Started.Open the Hood.Find Oil Drain. Locate the oil drain plug underneath the vehicle.Drain Oil. Set up the workspace, drain oil and replace plug.Find Oil Filter. Locate the oil filter.Remove Filter. Position drain pan and remove ...

Read more

Where do you put a tire jack on a 2007 Chevy Cobalt?

Under control arm or pinch weld

Read more

How often should serpentine belt be changed?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

How can you bypass a serpentine belt on a 2002 converible sebring from the ac compressor?

You realy can't. If your intention is not to power the A/C unplug the wire that connects to the electric clutch. It should be right behind the pully.

Read more

Do 2005 Chevy Trailblazer's have timing chains or belts to replace?

Timing chain, no maintenance required.

Read more

How do you take out a broken speed sensor on a 2005 Chevy silverado?

Assuming you mean the vehicle speed sensor, it'll be located atop the transmission near or on the transmission output. Disconnect the wiring (should be a simple weatherpack terminal), then unbolt the VSS.

Read more

Are there any recalls on 2010 Chevy Cobalt?

General Motors LLC (GM) is recalling certain model year 2010 Chevrolet Cobalt vehicles manufactured January 4, 2010, to June 23, 2010.The affected vehicles may be equipped with an improperly routed Side-Impact Sensor (SIS) wiring harness in the driver side front door.

Read more

How important is a serpentine belt?

Well, it won't keep your pants up, but it does transport power to your vital automotive components.The serpentine belt is one long, snaking, winding belt that keeps your alternator, power steering pump, air conditioning and — in some cases — your water pump running smoothly and effectively.

Read more

How do you get the tensioner to move on 1988 caravan to replace serpentine belt having a diffucut time trying to get belt on?

You don't mention which engine but on my 90 3.3 I put a wrench on it and just move it. It's kinda hard.

Read more

How much is a new Chevy Cobalt?

The Chevrolet Cobalt is available as a coupe and a sedan.Inventory prices for the 2010 Cobalt range from $90 to $10,822.It gets EPA-estimated 26-30 MPG combined.NEWTake our quiz & meet the car you'll love.

Read more

How do you change the serpentine belt on a 2002 Chrysler town and country mini-van 3.8 engine?

There should be an idler pulley that you need to loosen to take belt off, draw a diagram of how the belt looks before you take it off so you can see how it goes back on.

Read more

How do you know if your serpentine belt is going bad?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

Where is the purge valve located on 2006 Chevy Cobalt?

Probably inner fender. It purges gas fumes at start up so you can always follow the line from the tank to find it.

Read more

How do you route smaller serpentine belt on98 zx2 to bypass ac compressor?

The belt that I used my my 1999 ford escort ZX2 is a 6K730 to bypass the A/C. when routing the difference is the belt will come from the power steering to the tension pulley to the crank then water pump and the rest is normal. I hope this helps

Read more

How do you restart a 2000 alero that broke the serpentine belt?

Serpentine belts don't just break. There is probably an accessory that is locked up such as the alternator or a idler pulley. Check each pulley that the belts contacts and make necessary repairs before installing a new belt. Once you have done that just start the engine back up as you normally wo...

Read more

How do you release the belt on 2000 model gu patrol to remove alternator?

Loosen the tensioner pulley. The tensioner pulley will slide to the right. This will loosen the alternator belt. So it can be removed.

Read more

Where could you find an illustration on replacing serpentine belt on '97 Buick Park Avenue?

There should be an illustration in your ownners manual.Just had mine done.. mechanic had to remove psgr side motor mount to release belt. Not a fun job.trust me this ne job you want to pay someone to do, you need to lower the engine cradle to remover the PS motor mount,you could also visithttp://...

Read more

How do you remove a Chevy blazer filler neck?

Remove all fasteners behind the filler neck door that attach the upper filler neck assembly to the car body. Remove ground strap if applicable. Loosen and slide clamps up from tank end of filler neck then wiggle the filler hose assembly off the tank and out. Take care not to allow dirt and crud t...

Read more

Routing new serpentine belt on 94 Plymouth Voyager?

When routing a new serpentine belt, make note of how the old belt was routed. Take a picture of the belt routing if possible. Also most cars have a sticker under the hood with the routing on it.

Read more

Can a serpentine belt be put on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

How much weight can a Chevy Cobalt carry?

Weight was average in-class, at 2,681 lb (1,216 kg) for the coupe and 2,747 lb (1,246 kg) for the sedan.

Read more

How much does a 2010 Chevy Cobalt cost?

The 2010 Chevrolet Cobalt LS Coupe and Sedan have a Manufacturer's Suggested Retail Price (MSRP) starting around $17,000, the Cobalt LT adds another couple hundred dollars and the SS starts around the $25,000 mark.

Read more

Why cant you detension the serpentine belt tentioner the bolt keeps rotating and not letting you get the belt on?

because the bolt is striped or you pulley is no bad take it off and get another one

Read more

How do you remove broken key on a 89 Chevy Camaro?

Your best bet is to hire a locksmith.

Read more

How do you remove the governor on a 96 Chevy Caprice?

you dont its computer controlled you might be able to have the computer reprogrammed

Read more

How do you remove the inside door handle on a 1996 Chevy van?

You will probably have to remove the whole inside door panel in order to remove the handle. The panels are usually held in place with screws or plastic clips. A Haynes Manual might be helpful.

Read more

What happens when the serpentine belt breaks on a car?

when serpentine belt breaks alternator and water pump stop working along with power steering pump

Read more

How do you remove the door panel on a 2014 Chevy Silverado?

Read more

How do you remove and replace grille emblem on 1957 Chevy?

The nuts holding the emblem are in the back. You have to get behind the grille to remove them.

Read more

How do you remove the front drive shaft on a 2000 Chevy Silverado?

Read more

How many o2 sensors does a Chevy Cobalt have?

A vehicle may have two to five oxygen sensors, and sometimes even more.

Read more

How many miles per gallon does a Chevy Cobalt get?

Chevrolet Cobalt MPG.With the 155-horsepower 2.2L I4 engine, 4-speed automatic transmission, and front-wheel drive, the 2010 Chevrolet Cobalt has been averaging 31 MPG (miles per gallon).

Read more

How do you remove the wheel cylinder on a Chevy Corsica?

after emoving wheel and brake drum you will have to teke brakes off. i usually do one side at a time so i can see how to put the springs back on. once brakes off indo brake line and tthen the two bolts that attach it to backing plate. after replacing you will have to bleed brakes

Read more

How do you remove the door panel on a 2007 Chevy Silverado?

Read more

How do you remove interior door handles on 2000 Chevy venture?

There should be two bolts on each side of each handle. Get a screw and as carefully as you can unscrew them and tack the handle off.

Read more

Is there a recall on 2006 Chevy Cobalts?

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2005-2010 CHEVROLET COBALT AND MODEL YEAR 2007-2010 PONTIAC G5 VEHICLES EQUIPPED WITH ELECTRIC POWER STEERING.THE DRIVER MAY EXPERIENCE A SUDDEN LOSS OF POWER STEERING ASSIST THAT COULD OCCUR AT ANY TIME WHILE DRIVING.

Read more

How do you remove the steering wheel on a Chevy truck?

Read more

Can you drive with a bad serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Can you drive a car with a broken serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Do I need to replace my serpentine belt?

Most serpentine belts generally last between 50,000 and 100,000 miles.Eventually, your car's serpentine belt will wear down from continuous exposure to heat and friction and will need to be replaced.

Read more

Can you drive a car with a bad serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

How much does it cost to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more