How do you identify 1993 GMC Sonoma ecu id?

Cars & Vehicles
GMC Sonoma

There should be a sticker on the unit that has the GM part number on it.

Previous questionWhen a car loses contact wirh pavement abd rides in watet is?
Next questionWhat types of transportation is used in the Sahara Desert?

Related question

Which pully do you loosen to change the belt on a 1993 GMC Sonoma?

Look for the idler pully,it will be the one that runs against the back of your surpentine belt,It is spring loaded,it is smooth,use a breaker bar or 1/2 drive ratchet,there is a bolt head that sticks out of the front of the pulley find a socket that fits this bolt head it should be metric,make su...

Read more

How do you remove fuel pump in 1999 gmc sonoma?

the fuel pump is a in tank pump, you have to drop the tank, its located inside the tank.

Read more

Why would a 1993 gmc sonoma 4.3 gets codes 42 and 43?

I can't make any promises, but I've got 94 Chevy using OBD1, like yours probably has too. In my manual this is what it says: Code 42:Ignition Control Module - "Check the wiring and connectors between the ignition module and the ECM. Check the ignition module. Replace the ECM".Code 43:Electronic S...

Read more

Where can i find a Radio Wiring Diagram for 1993 GMC Sonoma?

You can find a radio wiring diagram for a 1993 GMC Sonoma in the vehicle's owner's manual. You can also find it at local auto parts stores.

Read more

What is the firing order on a 2.5L 1993 gmc sonoma?

Knowing the firing order of a car's engine can help troubleshoot problems later on. The firing order for a 1993 GMC Sonoma 2.5L engine is 1-6-5-4-3-2.

Read more

How do you install a body lift kit on a gmc sonoma?

The best way to install a bodykit on a GMC Sonoma is to have the work done by a professional bodyshop. I would not recommend trying to do this yourself. At American Car Imports in London we arrange to have bodykits installed on new Ford Mustangs, such as on our ACI Racing Mustang Outlaw and ACI R...

Read more

How do you change oil pan seal on 1995 GMC Sonoma?

A GMC/Chevrolet 4+4 truck would require dropping the front differential or removing the engine to remove the engine oil pan. I would suggest purchasing a shop repair manual if you are going to "DIY".

Read more

How do you tighten the steering column in a GMC 1991 Sonoma?

If your referring to having loose steering, then you need to tighten the adjustment set screw on the steering box under the hood. Don't tighten this to much, or it will lock up the gears. Typically a loose box needs to be replaced, in very few cases will tightening the set screw actually help.

Read more

How do you fix a broken concentric slave cylinder bleed valve on a 98 gmc sonoma?

Replace the slave cylinder.

Read more

Where do you find the 135 plugs on a 2002 GMC sonoma V6?

135 plugs???? What are you referring to?Maybe the #1, #3 and #5 spark plugs? If so they would be on the drivers side of the engine.

Read more

Does GMC still make the Sonoma?

During the final year of the GMC Sonoma in 2004, the crew cab was the only version of the truck available.In 2005, the GMC Sonoma was replaced by the larger Canyon mid-sized pickup truck.

Read more

What type of freon do you use in a 1996 GMC Sonoma R12 or R132a freon?

R-134a(1990 CLEAN AIR ACT)Most cars after 1992 have R-134a

Read more

Where is the ERG valve located on 1993 GMC Jimmy and how do you replace it?

Assuming 5.7 V8, it's on the passenger side, a few inches to the side of the throttle body.

Read more

How do i change the evaporator on a 1997 GMC Sonoma?

You get the refrigerant evacuated first - just trying to open the line up and release it into the atmosphere is both illegal and very dangerous. Then you have to open up the HVAC compartment, and it's a pretty simple process to disconnect the evaporator... once you've swapped out the evaporator, ...

Read more

Is there a wiring diagram for a 1998 GMC Sonoma?

As we're not allowed to post links here, either in the answer text or as related links, I can only direct you where to go... there's an S10 forum... in fact, take the space out between the words "S10" and "forum" and add the dot com at the end, and it'll take you right to it. Scroll down to the "...

Read more

How do you replace a window motor on a 1993 GMC Jimmy?

Disconnect the battery, Remove the door panel, vapor barrier plastic, power window connections, and I would remove the entire regulator assembly with motor attached. It helps to have someone hold the window as it drops inside of the door. Some motors are riveted to the regulator at the factory, s...

Read more

Can a 2001 GMC Sonoma 4x4 be flat towed?

If you can put the transfer case into neutral (which you need either a manual transfer case or the four button electronic case), yes. Otherwise, the only way you can without damaging the driveline is to either have a manual transmission or remove the driveshafts.

Read more

What is the sterio unlock code for 1998 gmc sonoma?

The unlock codes for GM vehicles can be set by the owner so if it is a used stereo there is no way to answer this question. Sometimes, however the owner will write their code in the owner manual on the page where the procedure is located.

Read more

Where is a iat located on a 2003 gmc sonoma?

If a 2.2, and like the o1, it is an intergrated unit mounted at the throttle body, combined with the map sensor, connector will have 4 wires..center of engine, connector is pluged in from the pass side , looking at engine seft to right.

Read more

A squealing belt on a 2001 GMC sonoma?

A worn belt will cause a squealing noise. The squealing noise is caused when the belt slips. Tightening the belt will temporarily fix the problem.

Read more

How do you identify a camshaft's size?

there should be a number stamped on the front of the camshaft. provided you know the manufactorer, go to their website, type the number in and you will see whats called a Cam Spec Card with all duration, lift, and lobe seperation.

Read more

How do you identify a commercial vehicle?

Read more

How do you identify corrosion?

to identify corrosion is to look for rust of pittedaluminum gets a white powdery fill, usually to salt exposer.copper gets a green powdery fill.

Read more

What is an ecu for an 99 gmc suburban?

An ECU is essentially the brain for a 1999 GMC Suburban. Without an ECU the truck will not be able to operate at all.

Read more

What size fan clutch wrench do i need for a 4.3 sonoma 1993?

An 1 1/2" open end wrench will fit a little loose but works fine.

Read more

What tires can you put on a 1993 gmc jimmy?

OEM tire size is 205/75-15. You can install 215/70-15.

Read more

How do you identify a fastener?

As a general rule, the length of fasteners is measured from the surface of the material, to the end of the fastener.For fasteners where the head usually sits above the surface such as hex bolts and pan head screws, the measurement is from directly under the head to the end of the fastener.

Read more

How do you identify a dangling modifier?

Recognize a dangling modifier when you see one.Modifiers are words, phrases, or clauses that add description.In clear, logical sentences, you will often find modifiers right next to—either in front of or behind—the target words they logically describe.

Read more

How do you identify a dangling participle?

A participle that is in the sentence but that does not modify a noun or pronoun in the sentence is called a dangling participle.Often, a dangling participle will occur at the beginning of a sentence.The sentence begins with a participle phrase, but then the subject of the sentence is not what tha...

Read more

Where do I add transmission fluid on a GMC Sonoma Truck 1995?

Down the automatic transmission dipstick tube.

Read more

How do you identify government vehicles?

the government vehicles have white no. plates,so we can identify after watching it's no. plates.

Read more

How do you identify a camshaft?

Locate the ID number on the camshaft.It is typically located in the center of the cam between the lobes.The ID number will consist of either eight or nine digits; the last four numbers identify the cam and its specific application.Match the number to a Chevrolet camshaft part number listing.

Read more

How do you identify a differential?

The BOM will identify the model number, the gear ratio, the type of differential, and all component parts.Traditional BOM's are 6 digits followed by 1 or 2 digits and start with the numbers 60 or 61.On some tags, the first 2 digits don't appear on the tag, but they must be used to identify the axle.

Read more

How do you identify functional groups?

Read more

How do you identify a gas cylinder?

The permanent stamp on the cylinder neck is the primary means of identifying the contents of a gas cylinder.The distinctive colour and a label on the cylinder neck also help to identify the cylinders.

Read more

How do you identify a preposition?

Read more

How do you identify a crane cam?

How to Identify a Crane Cam Examine both ends of the camshaft. The end of the camshaft will be embossed with a two-digit engine prefix code, a grind number, and the series name of the camshaft. Using the information on the camshaft, look up the information in the Crane Cam Catalog. The catal...

Read more

How do you replace a starter on a 2002 sonoma?

Disconnect the - battery cableRaise and support vehicleDisconnect wiring at the top of the starterRemove starter mounting boltsRemove starter

Read more

How do you identify a broken spark plug?

take a test light. ground the test light to the battery then take the test light and move it around the suspect spark plug if the plug wire or spark plug are cracked or defect the spark will go to the test light and you will see the spark. if you don't see any spark its not broken.You can also us...

Read more

How do you identify the engine of an Chevrolet?

If you are talking about the small block V-8 Chevy engine, there is a small flat pad with an engine id number located on the block, in front and below the passengers side cylinder head. Using that number, visit web Chevrolet engine identification sites to determine which engine you have.

Read more

Where is the brain box located in a 1998 GMC Sonoma?

Under the hood on top of passengers side inner fender.

Read more

How many gallons of gas does a GMC Sonoma 91 hold and what is the mileage via highway per gallon?

The miles per gallon on the highway for this car is between 21 and 26 miles per gallon. The gas tank capacity for it is 20 gallons.

Read more

How do you reset the ecu in es 300?

There are two ways you can reset the ECU. You can disconnect the positive battery cable for a few minutes or you can pull the ECU fuse for a few minutes.

Read more

Where is the location bleeder screw on a 03' gmc sonoma 2.2?

On the brake calipers.

Read more

Would a 4.3 V6 out of a 94 Astro van fit in a 93 GMC Sonoma?

Yes. If it's coming out of a vehicle with an automatic transmission and going into one with a manual (or vice versa), then the ECM will need to be reflashed.

Read more

How do you know if your car's ECU is broken?

the car will run rough, and the check engine light will be on. and depending on the car, it could possibly not run at all

Read more

Where is the fuel tank pressure sensor located in a 1998 gmc sonoma?

It is important for a car owner to know the location of all the car parts. The fuel tank pressure sensor for a 1998 GMC Sonoma is located in the fuel pump assembly.?æ

Read more

What year did General Motors come out with the gmc sonoma?

The GMC S-15 became the GMC Sonoma in 1991.

Read more

How do you tune your ecu for a turbo?

An ECU will require a proper tuning computer system. There a several available on the market. Then the car will require a DYNO test to allow the engine's turbo to be calibrated according to the response of the engine. This allows for the best fuel, air, and spark readings.

Read more

How do you reset a 1994 VW jetta's ECU?

You can either pull the fuse or unhook the car battery.

Read more

How do You make the ecu give a code?

It depends on the year, make and model vehicle, give us more info.

Read more

Where is heater core in 1993 GMC Suburban located?

Under the dash near the firewall. Good Luck!

Read more

Where is the starter in a 1993 GMC vendura van?

passenger side rear of motor

Read more

What are the engine sizes for a 1992 GMC Sonoma are there more than one V6?

1992 GMC TRUCKS SONOMA 2.5L 4-cyl Engine Code A 2.8L 6-cyl Engine Code R 4.3L 6-cyl Engine Code W 4.3L 6-cyl Engine Code Z Good Luck and Remember. Change Your Mind, Not Your Oil. Use the First In Synthetic Motor Oil's. See My Bio For Information & Contact Details.

Read more

How do you start a GMC Sierra?

PUSH 'LOCK' TWICE THEN PRESS AND HOLD SEMICIRCLE The vehicle will start up and remain running for 10 minutes, or until the driver gets in and either puts the key in and turns to on, or pushes the start button.

Read more

Where is the door lock mechanism in a 1995 GMC Sonoma?

The 1995 General Motors/GMC Sonoma has the door lock motors and actuator assemblies. These are located in the driver and passenger side doors, behind the door trims.

Read more

What are the two black relay boxes under the hood of a 93 gmc sonoma?

The two black relay boxes under the hood of a 1993 GMC Sonoma are fuse boxes that control part of the electronic devices in the vehicle. One of the boxes also houses the battery below it.

Read more

Will a low oil pressure switch reset itself on a 2002 GMC Sonoma 4.3?

A low oil pressure gauge has no reset. It comes on to tell you that the oil pressure is dangerously low. It will not go off until the pressure is restored. You may be low of oil or the pressure sensors may be defective.

Read more

How do you identify a ford 302 ho motor?

One way is the firing order. The 302 HO has the same firing order as the 351. So, if the firing order is 1-3-7-2-6-5-4-8 you have an HO engine. If the stock manifold is on the engine, it will say "5.0 Ford HO". The exhaust manifolds were factory tubular headers. They had roller cams.

Read more

How do you identify a Chevy transmission by VIN code?

Call a Chevy dealer's service department and they can look the information up by the VIN. Typically, if you know make, model, year, and what the engine is, its pretty easy to figure out what the transmission is.

Read more

How do you identify a binary covalent compound?

Rules for naming simple covalent compounds: Name the non-metal furthest to the left on the periodic table by its elemental name.Name the other non-metal by its elemental name and an -ide ending.Use the prefixes mono-, di-, tri-. to indicate the number of that element in the molecule.

Read more

How do you identify the broken motor mount?

I would say 1st locate motor mounts.if it is rear wheel drive they should be too the right & left of engine .If it is a front wheel drive will be near fron possibly top called wish bone.May have one to left of the motor,While looking into the egnine.quite possibly near lower rear of engine by...

Read more

How do you identify positive terminals in voltmeters and ammeters?

The positive terminals in voltmeters and ammeters are generally indicated by a red coloring and a + (plus) symbol. Negative is generally black and - (minus).

Read more

How do you identify a flat head inline 6 engine?

The easiest way to identify a flat head engine is that there aren't any valve covers. The Cylinder head is what you see and you will notice alot of bolts. These are all the head bolts exposed, on a inline 6 cylinder there will usually be 33 bolts.The cam is in the center of the engine and valves ...

Read more

How do you identify a long stroke brake chamber?

The 'type' of brake chamber, in terms of its size, for all brake chambers is determined by using a caliper or a tool ('Chambermate') to measure the outside diameter.The 'type' of brake chamber, in terms of its stroke, is determined by looking for visual identifiers that indicate it is a long stro...

Read more

How do I find my radio ID?

Tune to Ch.0 or select the MORE button on the touch screen.Then select Sirius Travel Link, then the Sirius button and the Radio ID will display.Starting in MY13 – XM Band Radios (VP1,VP2,VP3,VP4): (ignition on/radio on): Tune to Ch.0 and the Radio ID will display.

Read more

How do you tune an ecu on a car?

fist u have to take it to a shop or if u know someone with a computer like a (snap on) and u gotta go threw the steps and it will let u edit all of it like fuel ratio air flow throtel reponse...ect

Read more

How do you install aftermarket ecu in skyline?

Every Skyline from R32 R33 R34, has the ECU behind the passenger Kick Panel on left side.remove the panel with a few phillips head screws, then the ECU needs to be removed with a 10mm wrench or socket in three spots. then swap, and enjoy your new ECU

Read more

How do you fix ECU on Jeep Wrangler?

You start by diagnosing and figuring out exactly what the issue is. I mean, given the nature of your question, it makes me a bit skeptical you even did any diagnosis to come to the conclusion that your ECU is the problem.If you don't want to waste money throwing parts at something until you throw...

Read more

How do you know if your ECU is bad?

Engine stalling or misfiring Another symptom of a bad or failing ECU is erratic engine behavior.A faulty computer may cause the vehicle to intermittently have issues such as stalling or misfires.The symptoms may come and go, and may not appear to have any sort of pattern to their frequency or se...

Read more

How you get car ecu programming course?

There's no such thing.Go to an engineering college, where among other things, you'll learn to program in various assembly languages and design advanced circuitry. Perhaps then you'll be able to even slightly grasp what happens inside of a car's ECU. All of it is coded in a VERY low level language...

Read more

How do I identify a Honda transmission?

It is also on the Certification label attached to the driver's doorjamb, and is stamped on the engine compartment bulkhead.The VIN is also provided in bar code on the Certification label.The Engine Number is stamped into the engine block.The Transmission Number is on a label on top of the transmi...

Read more

How do I identify my wheel manufacturer?

How to Identify an Alloy Wheel Brand Inspect the wheel cap. The cap is the part that covers the car's hub where it comes through the center of the wheel. Inspect the rim of the wheel. Turn the wheel over so that the back can be inspected. Look for a logo or the name of a wheel manufacturer...

Read more

How do I reset my car ECU?

Another way to reset your ECU system Pull out your car's key.Pull out the fuse as well.Wait for 15 seconds and put it back in.

Read more

How do I learn to program ECU?

ECU programming guide Connect the vehicle interface cable to the OBD-II connector and turn the ignition switch to ON.Open the ProECU software and choose Tools then Detect Vehicle.Select Program Engine ECU.Choose Query ECU to identify the ECU version fitted to the car.

Read more

How can you identify a real buyer?

they need to be willing to come and look at the car and you need to be able to feel like they wont scamyou, its all in your head its whatevr you think

Read more

How do I find out my state ID number?

Call your DMV office or visit Top Shelf Domains to launch your business.to find out what your state requires in order for you to get a state ID card.Call your DMV office if you have lost your ID card or it has been stolen to find out what is required for you to obtain a new ID number.

Read more

Do you have to carry ID in Spain?

To conclude, if you are in Spain, you must carry a valid ID card or passport at all times, and failure to do so could see the police detain you temporarily whilst they ascertain your identity, and furthermore, it is within their rights to issue a fine.You've been warned.

Read more

How many quarts of tranny fluid does a 1993 gmc siera hold?

That would depend on whether the transmission had been in service, and only what was in the transmission was drained - the torque converter holds nearly as much as the transmission, and does not drain out unless the torque converter is removed... Either way, it is listed in your owners manual...

Read more

How do I reset my car's ECU?

Another way to reset your ECU system Pull out your car's key.Pull out the fuse as well.Wait for 15 seconds and put it back in.

Read more

How do I program my car ECU?

ECU programming guide Connect the vehicle interface cable to the OBD-II connector and turn the ignition switch to ON.Open the ProECU software and choose Tools then Detect Vehicle.Select Program Engine ECU.Choose Query ECU to identify the ECU version fitted to the car.

Read more

Ihave a 1997 gmc sonoma that you changed the fuel pump and filter now your fuel gauge doesn't work any info would help thank you?

there is a plastic box attached to a metal arm on the pump if it was inside the tank the arm has to be able to float up and down it reads the amount of gas in the tank, its stuck

Read more

Will a vortex 4.3 liter bolt up in a 87 gmc sonoma s15 that has a 2.8 liter v6?

NO! Not to the stock tranny, The 2.8 is a 60 degree engine, the 4.3 is a 90 degree engine, trans bolt pattern different, use a 700R4, 200R4, or turbo 350.YES! with motor mount adapters (from JTR.com) the stock 2.8 mounts are the favorite with Engine swappers. Check Ebay under "S10 V8", also check...

Read more

How do I identify my engine?

It's all in the engine code (sometimes referred to as engine number) or vehicle identification number (VIN).You can find the VIN in the lower corner of your windshield on the driver's side.In the series of numbers and letters, the tenth from the left denotes the model year and the eighth is the e...

Read more

How do I identify a 46re transmission?

AUTOMATIC TRANSMISSIONS The identification plate is attached to the right side of the transmission case.The 42RE/44RE/46RE is a 4-speed fully automatic transmission with electronic governor.The ID numbers are stamped on the case's left side just above the oil pan.

Read more

How do I identify my Chevy engine?

How to Identify a Chevy 350 Motor Look at the rear of the engine block for casting numbers, by where the transmission mounts to the engine. Write down that number, and go to MorTec.com. Look for a second casting number on the rear of the block. Look at the front of the block, just forward ...

Read more

How do I identify a Cleveland engine?

2V and 4V stands for the number of venturis not the number of valves.To tell which casting # the head have, you have to pull them off the engine.Casting numbers is at the bottom off the cylinder head.To determine if its a closed chamber 4V you can pull the valve cover and read the date code.

Read more

What do you need at the DMV for real ID?

To apply for a REAL ID driver license or identification card, you must visit a DMV field office and provide: Proof of identity (one document) Proof of Social Security number (one document) Proof of California residency - street address. (

Read more

How do police men identify license plates?

Patrol cars use innovative technology that allow it to remember each license plate it passes by. They use this technology to make sure that cars are not stolen or to make sure the owners are not wanted. Locals do not appreciate this technology because it is an invasion of privacy.

Read more

How do I identify a key fob?

Read more

How do I identify my club car?

The first two numbers of the serial number is the year of your Club Car golf cart.Here are two examples: If the first three digits of the serial number are “A00”, you own a 2000 Club Car DS.If the first four digits of the serial number are “PG09”, you own a 2009 Club Car Precedent.

Read more

How do I identify a Mustang transmission?

To identify your Ford Mustang transmission, you will want to locate the first number underneath the "TR" code at the bottom right hand corner of the door tag.The only number you need to pay attention to is the first number or letter listed.For TR codes that start with a K, you have a Mustang tran...

Read more

How do I identify GM engine block?

How to Identify a GM Block Locate the engine ID number. On small-block V8s, it is located on the passenger-side front of the engine block, right below the cylinder head. Decode the ID number prefix. The prefix is five-digits long and begins with a letter. Cross-reference the engine ID numbe...

Read more

How do I identify a Ford transmission?

How to Identify Ford Automatic Transmissions Inspect the pan found on the bottom of the transmission. According tio Kelly Hot Rod, many Ford Automatic transmissions, especially the C-series, can be identified by the bottom pan shape and the bolt count. Count the number of bolts on the transm...

Read more

How do I identify my Ford transmission?

How to Identify Ford Automatic Transmissions Inspect the pan found on the bottom of the transmission. According tio Kelly Hot Rod, many Ford Automatic transmissions, especially the C-series, can be identified by the bottom pan shape and the bolt count. Count the number of bolts on the transm...

Read more

How do you tune up a 2003 sonoma SL pick up?

A typical tune up involves changing all of the basic wear parts. For example start with the spark plugs and air filter. Change the oil and top off the fluids. This means the engine oil, transmission oil, engine coolant, power steering fluid, and windshield washer fluid. These are basic items that...

Read more

Where do you plug in a 2003 Sonoma?

The spark plugs in a 2003 GMC Sonoma can be changed relatively easily with a socket wrench. However, the spare wheel must be removed from the wheel well to allow access.

Read more

How do you tell what size ring gear in 2000 sonoma?

You could remove the diff cover and count the number of teeth on both the ring and pinion gears, then divide the number of teeth in the pinion into the number of teeth on the ring gear and you will have the ratio.

Read more

How do you take a door panel off of a 1999 Sonoma?

An instructional video on how to take a door panel off a 1999 Sonoma can be view on YouTube. Search for "How to remove door/door panels 1999 Sonoma/s10" and click on the first search result.

Read more

Can car seats go on the fold down seats in the back of a gmc sonoma pickup?

Yes, it is legal to put child car seats on the fold down seats in the back of a pickup truck. You should follow the same instructions on the car seat for these types of seats.

Read more