How do you get the tensioner to move on 1988 caravan to replace serpentine belt having a diffucut time trying to get belt on?

Cars & Vehicles
Serpentine Belts

You don't mention which engine but on my 90 3.3 I put a wrench on it and just move it. It's kinda hard.

Previous question98 Toyota Avalon heat cool sys runs for 2 sec when start car then will not work does this each time car is started any ideas thanks rudolphdoptonlinenet?
Next questionWHY does a 1992 Hyundai excel to stall out shorty after running I replaced spark plugs rotor cap plugs ignition coil..still does the same thing.?

Related question

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

How do you replace serpentine belt on a fx 35?

1. Remove front engine undercover.2. Loosen idler pulley (alternator and power steering oil pump belt) lock nut and adjust tension by turning bolt.3. Same is done for the other idlery pulley (A/C compressor belt).

Read more

How do you replace serpentine belt on 2005 Equinox?

Begin by loosening the tensioner pulley on your 2005 Chevrolet Equinox. The serpentine belt will become loose and can be removed. Reverse the process to install your new serpentine belt.

Read more

Can your AC not working have anything to do with the mechanic just replacing the drive belt tensioner and serpentine belt?

Check to make sure the belt is routed around the compressor pulley. Also check the wiring connector at the compressor in case it was dislodged.

Read more

Do you have a diagram of how to put the serpentine belt on the pulley?

You may get an answer if you list the vehicle & engine you are talking about. You are not going to get an answer to this question as is.

Read more

How do you tighten a timing belt tensioner pulley?

To even out the tension in the belt, use a spanner or socket wrench on the crankshaft-pulley bolt and turn the crankshaft two full turns clockwise.Tighten the locking bolt first to hold the tensioner in its new position.Tighten the pivot-spring bolt, which has a precise torque setting.

Read more

How do you adjust a timing belt tensioner?

To even out the tension in the belt, use a spanner or socket wrench on the crankshaft-pulley bolt and turn the crankshaft two full turns clockwise.Tighten the locking bolt first to hold the tensioner in its new position.Tighten the pivot-spring bolt, which has a precise torque setting.

Read more

Is a belt tensioner supposed to move?

Appearance: Move the tensioner arm (tensioner being mounted on the engine) through its entire range of motion with a wrench.There should be resistance to this movement.If there is none, the spring has lost its force.Other indicators are belt squeal from slippage, or loss of rotation of a belt-dri...

Read more

How do you check a timing belt tensioner?

Listen.A bad tensioner will usually be accompanied by noise.This noise could be some type of squealing or rattling coming from the timing cover area.Also, when your timing belt is loose, it will cause some drivability issues usually under high load or high rpm.

Read more

Where is the tensioner pulley to tighten the serpentine belt on a 2000 Chevy Silverado?

If you're standing at the front of the truck and looking into the engine compartment the tension pulley is on the left side about half way down.

Read more

How do you replace the serpentine belt on a 1993 Mercury Cougar?

To remove the serpenteen belt on this vehicle, you must first locate the spring loaded tensioner. You will need a 1/2" breaker bar or a socket to recoil the spring load. doing this will release the tension on the belt. You can then remove the belt.NOTE: If you are just changing the belt with a ne...

Read more

How much does it cost to replace a belt tensioner?

Know what price you should pay to get your vehicle fixed.The average cost for a drive belt tensioner replacement is between $209 and $239.Labor costs are estimated between $73 and $94 while parts are priced between $136 and $145.Estimate does not include taxes and fees.

Read more

How do you release the belt tension at the tensioner?

There are two types of tensioners, spring tension, and bolt adjusted tension.spring tensioners, place the appropriate sized wrench on the nut in the middle of the pulley and turn clockwise, the wrench will give you ample leverage to pull back the arm with ease.Bolt adjusted, you will need to loca...

Read more

How do you replace a serpentine belt on a 1995 Chevrolet Camero?

Replacing the serpentine belt on both V6 & V8 rear drive engine are fairly easy than front wheel drive. The belt is located just between the front of the engine and the radiator. You have plenty of clearance to work. Just need to losen the tension and the belt should come out. Putting the new...

Read more

How do you adjust the tension on a V belt?

Read more

Can you replace a serpentine belt yourself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How much does it cost to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How much does it cost to replace the serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How often does a serpentine belt need to be replaced?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

How do you get the accessory drive belt or serpentine belt off of a 1989 sunbird?

To remove the accessory drive belt or the serpentine belt from the motor on a 1989 Sunbird, it is necessary to loosen the belt tensioner. Look for a pulley that has a bolt in a slot. Loosen the bolt and move the tensioner so there is a gap in the belt. Then remove the belt from each pulley.

Read more

How expensive is it to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

How do you replace timing belt on 1999 Kia Sportage?

You should be able to find a shop manual for this at the local library...make copies of the right pages...good luck:)

Read more

Is a serpentine belt the same as a timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

How do you replace timing belt on seat leon 1.9tdi?

Replacing the timing belt is a very detailed task. It will include removing the engine. Timing belt replacement directions can be obtained from most auto-parts stores.

Read more

How do you loosen the tensioner pulley to change the belt on a 1997 ford F150?

It's spring loaded, use a wrench or socket to move it. If it's really stuck it may be seized.

Read more

Where is the serpentine belt tensioner on a 2.4 liter Dodge Stratus?

On my 2004, there are 2. Check the diagram on the fender well or near the radiator. It shows all the pulleys the belt goes around, including the tensioners.

Read more

How do you replace timing belt on 95 avenger?

In order to replace your timing belt on your 1994 Avenger, you will need to first drain your cooling system. Remove the timing belt and mounting bolts and replace with your new belt.

Read more

Need to find out how to replace serpentine belt?

Just pry the belt tensioner back and remove the old belt, and install a new one.

Read more

Do I need to replace my serpentine belt?

Most serpentine belts generally last between 50,000 and 100,000 miles.Eventually, your car's serpentine belt will wear down from continuous exposure to heat and friction and will need to be replaced.

Read more

How do you change a tensioner belt?

We need to know the year, make, model and engine size of the vehicle then we need to know if you want to change the belt tensioner or the belt or both.

Read more

How long does it take to replace serpentine belt?

How Long Does It take To Replace A Serpentine Belt? For professional automotive technicians with the right tools and training the replacement of a serpentine belt usually takes about 30 min to an hour.This time varies by the make, model, and year of vehicle that you're driving as some take longer...

Read more

How do you loosen a belt tensioner?

Snap a long-handled ratchet or a serpentine belt tool into the square 1/2-in.-drive or 3/8-in.-drive opening.Or use a socket on the hex-shaped protruding nut.Slowly rotate the tensioner arm as far as it will turn.Then release the tension.

Read more

When you try to replace the belt on your whirlpool dryer the belt slips off the pulley when you try to put it around the drum?

You don't have your tongue in the right position. Put the belt on the drum and motor and pull the tensioner pully over to install it there.

Read more

How do you reset the timing when replacing the belt?

Purchase the shop manual for your vehicle, it will save you money for this job and many more repairs.

Read more

How do you change a serpentine belt?

How to Replace a Serpentine Belt Take a good look at both your repair manual and your belt routing diagram under the hood before beginning. Look at the way the old belt wraps around the pulleys. Locate the self-adjusting tensioner and know that you need to be careful when releasing tension ...

Read more

How do you release Fan Belt tensioner On Peugeot 206?

Use a 3/8"extension bar to lever the tensioner ( there is a corresponding whole in the bracket that the tensioner pivots on).To hold it in position theres a whole where you can inset a bolt.

Read more

How do you replace the timing belt on a 2009 Santa Fe?

If you have the 3.3 V6 engine it doesn't use a timing belt. It has a chain which requires no maintenance.

Read more

How do you replace the Timing Belt on a 1994 Ford Aerostar 3.0L?

There isn't a timing belt on the 3.0. This engine has a timing chain which would require extensive work in the removal of parts. You don't have to remove the radiator but will have to remove all of the front of the engine accessories on the front of the engine to get to the timing chain. Not an e...

Read more

What is the cost to replace serpentine belt?

It is very inexpensive to replace a serpentine belt.The replacement cost is only going to be between $90 and $200 in most cases.The belt itself will cost between $25 and $75 while the labor costs will probably be between $75 and $120.

Read more

You replaced timing belt on 1999 Tahoe how do you set timing?

If you've already removed the timing cover there are markings on the top and bottom gears. Make sure they are lined up before putting the belt back on (if it has a belt) most chevys have timing chains. Anyway, once you've done that and reinstalled everything; the timing is adjusted by loosening t...

Read more

How do you remove serpentine belt on 2005 Chevy Cobalt?

You have to release the stress in the tensioners to remove the serpentine belt. When you put it back on there is a diagram under the hood of the car that takes you step by step.

Read more

What if you have dismantled the tension-er How do you get it back together?

you will need to loosen the bolt that hold the tensioneer back a little to slide it down so you can reach all belts around pulley. reverse the procedure after belts is on then use the ratchet or pry bar to thighten. good luck

Read more

Could replacing a timing belt and tensioners cause one hydraulic lifter to fire itsef through the casing?

You didn't mention the year, make or engine info but yes, it could happen if the belt was not installed properly. Expensive lesson.

Read more

How much does it cost to replace timing chain tensioner?

Know what price you should pay to get your vehicle fixed.The average cost for a timing chain tensioner replacement is between $918 and $1,139.Labor costs are estimated between $776 and $981 while parts are priced between $142 and $158.Estimate does not include taxes and fees.

Read more

How do i now the Timing belt tension on a escort rs turbo 1989 with out the right tool?

I would just buy the proper tool. If the belt jumps a tooth because it's to slack or breaks because it's to tight, it will cost you a darn lot more than the tool.

Read more

How do you replace an automatic belt tensioner on a '91 sable Pcv valve tie rod fram air filter?

You need a repair manual. Purchase one at most auto parts stores.

Read more

How do you replace a timing belt on a 2.4 Mitsubishi Eagle Summit?

Begin by removing all of the pulleys from the front of the engine. Remove the front engine cover. Remove the timing belt. Reverse the process to install the new timing belt.

Read more

Do you losen the altinator to change serpentine belt on a 94 Jimmy?

You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.

Read more

How do you loosen the belt tensioner on a 2003 excursion 6.0 PS?

Use a 1/2" or 3/8' breaker bar to hold belt tensioner open

Read more

At how many miles do you replace timing belt on a 2001 Honda Accord?

every 40 to 50 thousand miles or depend how much you drive it daily.

Read more

How often do timing belts need to be replaced?

Many car owners may wonder how often to replace a timing belt.The old rule was every 60,000 miles.As technology has improved, many manufacturers recommend intervals up to 100,000 miles.To be safe you should check what the vehicle's manufacturer recommends and stay within that mileage.

Read more

How do you change the serpentine belt on a 1994 mercury cougar xr7?

with a 1/2" rachet or breaker bar placed in the square whole on the tensioner pully, you push (from passenger side to drivers) which will release the presure on the belt. Might want to draw a "map" of how the belt goes cause it ain't obvious when its off the car.

Read more

How do you repair the serpentine belt on a 1998 Mitsubishi Galant?

You don't repair a serpentine belt. You replace the worn or broken belt with a new one.

Read more

How do you Replace water pump on grand caravan?

depends on which motor it has and what year it is 3.3 is easy 3.0 is pretty involved and depending on how mechanically able you are you should have the dealer or local garage do it.

Read more

How do you reroute serpentine belt to bypass ac compressor on 1995 town car?

If that model was available without a/c, you will need to purchase the belt for a 95 town car w/out ac, and follow the appropriate belt routing diagram for that model.

Read more

How do you loosen a trailblazer drive belt tensioner?

The easiest way to loosen the tensioner is to use an automatic belt tensioner. This can be used on a serpentine belt which is connected to every pulley on the engine.belt.

Read more

How do you tighten the serpentine belt on a 1997 Saturn?

You don't. The belt tension is automatically adjusted via a spring loaded tensioner. If the serpentine belt is noisy or worn out prematurely. replace the tensioner. The belt should be inspected for cracks and other signs of wear. Replace worn out belt(s) before they break leaving you stranded.

Read more

How do you replace struts on 1999 caravan?

You start by placing the vehicle on jack stands under the front frame section then remove the front tires then possiblly the brake calipers ,so the brake hoses do not get damaged from stretching thenunbolt the lower strut spindle bolts then the top mounting nuts from under the hood do this safely...

Read more

How much does it cost to replace a pulley and serpentine belt?

It is very inexpensive to replace a serpentine belt.The replacement cost is only going to be between $90 and $200 in most cases.The belt itself will cost between $25 and $75 while the labor costs will probably be between $75 and $120.Taxes and fees will be added onto these prices too.

Read more

Where could you find an illustration on replacing serpentine belt on '97 Buick Park Avenue?

There should be an illustration in your ownners manual.Just had mine done.. mechanic had to remove psgr side motor mount to release belt. Not a fun job.trust me this ne job you want to pay someone to do, you need to lower the engine cradle to remover the PS motor mount,you could also visithttp://...

Read more

Why cant you detension the serpentine belt tentioner the bolt keeps rotating and not letting you get the belt on?

because the bolt is striped or you pulley is no bad take it off and get another one

Read more

Im trying to replace the alternator in vw golf 2.0 ive managed to remove old one but im having trouble fitting the new one is there anywhere i can release the tension on the belt?

If this car has one belt (cerpentine) on it, there should be a tensionner pulley that you can use a ratchet or breaker bar to relieve tension to remove the belt. Same thing to put it back on when the alternator is in place.

Read more

How much does it cost to replace the timing belt on a 1997 RAV4?

Labor and timing belt only, aprox $400.

Read more

What does replacing the timing belt do?

Your timing belt helps run many fundamental parts of your car, including the vehicle's engine, alternator, air conditioner and power steering pump.In older vehicles, the standard timeframe to replace a timing belt is around 60,000 miles.

Read more

How do you loosen tension on drive belt fo the alternator?

There is an automatic tensioner that keeps tension on the belt. THere should be a label in the engine compartment somewhere giving you a diagram of the path of the belt and showing where the tensioner is and which way it turns to loosen the tension. On the 1995 GMC Sierra that I just worked on, I...

Read more

How do you release the tensioner to put belt back around the alternator?

This is easiest done with 2 people. Put the belt around everything but the alternator. On the tensioner pulley or the base of it, there should be a box or something that will fit a wrench. Get that wrench, and another of a similar size (you will probably have to do the 2 wrench trick to extend yo...

Read more

How do you align a serpentine belt pulley?

Read more

How do you replace belt on ls1?

Pardon me but what is an Is1?

Read more

How do you take find out how to put on a serpentine belt for a 3.3L V6 if you dont have the diagram on the van anymore or the original belt?

you don't say wot make an model... so i presume its the Chrysler new yorker as i cant think of another with a 3.3 v6.. easy answer.. buy a haynes manual.. if your gonna replace the belt.. you might as well do other stuff like replace the water pump and front engine seal while your at it..

Read more

Do you need to replace water pump when changing timing belt on mondeo titanium 58 reg?

you don't have to unless it is damagedbut it is usually good practice to do soI M Obetter of doing it when your at it saves having to strip it all down again to fit a new pump

Read more

There is a wheel at the top of the serpentine belt that you cant seem to get the belt over you have the belt assembled but you cant get pat this part HELP?

you need to loosen the tensioner.. ist like a small wheel with some sort of spring attatched..

Read more

Does a 2008 Dodge Grand Caravan 3.8 liter have a timing belt or chain?

The Dodge 3.8L has a timing chain that should last for the life of the engine. There is no service interval.

Read more

How do you change a serpentine belt on a Chevy Silverado?

Shop Products Familiarize yourself with the belt routing diagram.Insert a 3/8 inch drive ratchet into the belt tensioner.Pull the tensioner counterclockwise to loosen the belt.Pull the belt off the idler pulley.Release the tensioner.Pull the belt off and out.

Read more

How do you change a serpentine belt on a 2001 Chevy Suburban?

Read more

How do you change a serpentine belt on a 2001 Chrysler Town and Country?

How to Replace the Serpentine Belt in a Chrysler Town & Country Open the hood and find the belt tensioner pulley. Look at how the belt is routed around various pulleys. Use a wrench to rotate the belt tensioner pulley bolt and slide the old belt off of the tensioner pulley. Make sure y...

Read more

How do you change a serpentine belt on a 2008 Toyota Corolla?

Read more

How much does it cost to replace a timing belt on a Hyundai Sonata?

The average cost for a Hyundai Sonata timing belt replacement is between $478 and $603.Labor costs are estimated between $209 and $265 while parts are priced between $269 and $338.Estimate does not include taxes and fees.

Read more

How do you change the lower timing tensioner on a 1997 200sx 1.6?

Remove the center retaining nut on the tensioner. You will need to use something to jam the pulley, so it will not turn.

Read more

Can you replace a timing belt with a timing chain?

Would have to change pulleys for sprockets

Read more

How do you do you find the serpentine belt diagram for a Toyota RAV4 2001?

There should be a diagram under the hood somewhere. Normally on the fan shroud. Click the link for a diagram. If you do not see one search with the term "2001 Toyota Rav 4 belt diagram" and you will find a diagram.

Read more

How do you install a serpentine belt on a 99 Isuzu Rodeo?

There is a belt tensioner (spring loaded pulley that automatically keeps the belt tight) that needs to be temporarily slackened while the now loose belt is slipped off one of the accessories. Sorry, but I can't remember what tool is needed to loosen the belt tensioner. Just opening the hood and o...

Read more

How do you change a serpentine belt on a Mazda 3?

How to Replace a Mazda 3 Serpentine Belt Open the Mazda 3's hood and support it with the prop rod. Connect the belt-tensioner tool into serpentine belt tensioner and move the tensioner pulley away from the belt with the tool. Pull the belt off the engine accessory pulleys by hand. Stretch ...

Read more

When to replace timing belt on Ford Escape?

The timing belt on a Ford Escape should be changed every 100k miles to prevent breaks and costly repairs. This is a labor and time intensive process but will usually only be done 2 or 3 times over the life of a vehicle.

Read more

How do you release serpentine belt on a 89 Mercury Cougar?

You have to release your tensioners in order to release your serpentine belt. When you put the belt back on you have to follow the diagram on the hood of your car.

Read more

Do 2005 Chevy Trailblazer's have timing chains or belts to replace?

Timing chain, no maintenance required.

Read more

When should you replace your timing belt on 98 pathfinder?

hyow much play on the belt do you have. and also if there is any cracking of the belt replace now.

Read more

How do you replace the half shafts on a 1988 Toyota corolla?

jack up the car, put on stands. remove the front wheels, remove the nuts on the tie rod ends,and the lower ball joints, give the joints{ on the thick part of the metal } a good hit with a heavy hammer. this should let the joints come free.take the tie rod end loose first, then using a long pry ba...

Read more

How do I know if my timing belt tensioner is bad?

Listen.A bad tensioner will usually be accompanied by noise.This noise could be some type of squealing or rattling coming from the timing cover area.Also, when your timing belt is loose, it will cause some drivability issues usually under high load or high rpm.

Read more

Is the timing belt tensioner hydraulic on the fiesta 1.4 tdci?

Yes, the timing belt tensioner is hydraulic on the Fiesta 1.4 TDCi. Its construction ensures strength, chemical and thermal resistance for longer life.

Read more

How can you tell if you have a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

Where is the timing belt on 2001 Cherokee sport and how easy is it to replace?

The timing belt is not a belt on a Cherokee sport. It's a chain. It's located under a housing on the crank shaft. In order to replace it you will need to remove the alternator, the water pump, the a/c compressor, the radiator and the engine fans. An experienced mechanic can get it done in about 3...

Read more

How do you adjust serpentine belt on a 1999 Holden jackaroo?

On all U.S. vehicles that use A single serpentene the belt has an automatic tensioner. I suspect that your can does too. It could be stuck.

Read more

How do you replace the gearshift boot and knob on a 1988 ford escort pony?

1. Unscrew the shift knob and pull out the cupholders. To remove the cup holders, grab both cups, and pull towards you and up.On the side of the central console, take out the two interior clips from each side. Just pull out the central part and the whole thing will pull out.On the rear part of th...

Read more

How can you bypass a serpentine belt on a 2002 converible sebring from the ac compressor?

You realy can't. If your intention is not to power the A/C unplug the wire that connects to the electric clutch. It should be right behind the pully.

Read more

How often do you need to change the timing belt?

some vehicles the interval is every 60 thousand miles while other it is now 100 thousand miles

Read more

What happens if you put a serpentine belt on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

How do you stop serpentine belt from squeeking?

Replace belt and check all pulleys for wear or rough spot

Read more

How do you replace the windshield washer pump on a 1988 Celica GT?

Determine which side of the vehicle the washer reservoir is located by opening the hood and finding the fluid fill nozzle. Safely raise and support the front wheel on that side, and remove the wheel for access to the inner fender well.Remove the lower splash guard below the bumper. Many times thi...

Read more

How do you set a timing chain tensioner on a 2001 vw jetta?

chcek out your loacl partshouse and get a timing book

Read more

When you tried to move your Mountaineer it made a clunking sound and felt like you were trying to move with the brakes on?

The brake calipers were stuck. you should have them checked soon.To me a stuck caliper indicates badly worn pads, or a lack of lubrication, either way it will need to ba checked asap.

Read more