How can you tell the rear end gear ratio?

Cars & Vehicles
Differentials
Antique & Classic Cars

Simply by jacking both rear wheels off the ground,put it in neutral,handbrake off, and chock the front wheels, and then turn the rear wheel 10 revolutions, and count the number of revolutions the tailshaft makes. For example, if it makes almost 38 revolutions, the diff ratio is 3.78:1. Alternatively, If the diff is out and you can't find a ratio stamped on it,count the teeth on the crownwheel and pinion gears, and calculate the ratio from this.

Previous questionHow do you reset the ecu in the 2001 vw golf because i dont find any ecu fuse to remove in fuse box inside the car and in engine hood?
Next questionHi I'm wondering what the dial is beside my rev counter on my 106 gti think its oil temp or oil pressure also want to no where it should run to mines half way?

Related question

How do I know what gear ratio My rear end is?

Turn the wheel TWO revolutions and count the number of driveshaft turns.The number of driveshaft rotations will help you determine your rear axle ratio.For example, if it turned 3 and a half times, it's a 3.50:1 ratio.If it turned 4 and a quarter times, it's a 4.25:1 ratio.

Read more

What is the rear end gear ratio in a 1986 cutlass supreme sedan?

what is the ratio of gears in a 1986 cutlass

Read more

How much faster is a 393 gear rear end than a 300 gear rear end?

A 393 gear rear end would be quicker than a 300 gear rear end but the 300 gear rear end would be faster in the long run.

Read more

How can you tell what gears in a front end without splitting the casing?

as with almost all vehicles, by the serial number usually stamped in the case itself.

Read more

What is rear gear ratio?

Usually a whole number and decimal fraction, the drive-axle ratio is a comparison of the number of gear teeth on the ring gear of the rear axle and the pinion gear on the driveshaft.For example, a 4.11:1 ratio means there are 4.11 teeth on the axle's ring gear for each tooth on the driveshaft's p...

Read more

Does Chevy make a 10 bolt rear end with 342 gear ratio?

Yes I have one in a1990 silverado short bed with 350 and 5 speed automatic transmition.

Read more

How do I know my rear gear ratio?

Turn the wheel TWO revolutions and count the number of driveshaft turns.The number of driveshaft rotations will help you determine your rear axle ratio.For example, if it turned 3 and a half times, it's a 3.50:1 ratio.If it turned 4 and a quarter times, it's a 4.25:1 ratio.

Read more

How do I tell what gear ratio my Vin is?

How to Find Out the Gear Ratio With the VIN Number Find the VIN of your vehicle. It can be found on the sticker on the inside of the driver's side door or on a stamped metal plate embedded in the dashboard above the steering wheel. Identify the VDS section, the fourth through eighth digits o...

Read more

How do you find the gear ratio?

They can simply divide the number of teeth on the driven gear by the number of teeth on the driver gear to find the gear ratio.In the Using the Gear Ratio Formula activity students will use this formula to find gear ratios.

Read more

How do you tell if your car has a positive rear end?

I assume you mean posi-trac rear end. Raise both drive wheels off the ground. Turn one wheel and if the other wheel travels in the same direction it is posi-trac.

Read more

How do you read a gear ratio?

Two Gears Start with a two-gear train. To be able to determine a gear ratio, you must have at least two gears engaged with each other — this is called a "gear train." Count the number of teeth on the drive gear. Count the number of teeth on the driven gear. Divide one teeth count by the ot...

Read more

How do you calculate overall gear ratio?

To determine a vehicles speed from the engine speed by multiplying the circumference of the tire by the engine speed and dividing by the combined gear ratio.

Read more

How do you calculate gear ratio speed?

To calculate speed ratio, otherwise known as gear ratio, you divide the number of teeth of the input gear by the number of teeth of the output gear.

Read more

What was the gear ratio 26 spline 10 bolt posi rear in the 1978 elcamino?

The quickest way is to jack up the rear of the car or truck and turn the rear wheel 1 complete turn and see how many revolutions your pinion yoke turns. if it makes thee revolutions and a little over it could be a 308 four turns and a little over would be a 410 ect..

Read more

What does rear end and gear mean on semi truck?

Short answer, the number of driveshaft rotations to achieve one full rotation of the axles. E.g, a truck with a 3.55:1 gear ratio requires 3.55 turns of the driveshaft to turn the axle shafts one full rotation.

Read more

How do you calculate the gear ratio of a vehicle?

To determine a vehicles speed from the engine speed by multiplying the circumference of the tire by the engine speed and dividing by the combined gear ratio.

Read more

How can you tell if your rear rotors are bad?

Your brakes are the most important safety feature on your car.If you hear or experience any of the following symptoms of brake rotor problems, get them checked out right away.You feel a pulsation when braking: A pulsation in the brake pedal or steering wheel while braking is a common sign of warp...

Read more

What gears are in a gm 26029188 rear- end?

I just pulled one from the junkyard and mine is a 3.23 Posi with Discs out of a 1994 Camaro. That should be what you have. Make sure your car is sitting on LEVEL ground, Chock the front wheels and set the back on jack stands. throw the car in Neutral and rotate the wheels while looking at the Pin...

Read more

How do you know what gear ratio you have?

Divide one teeth count by the other.Now that you know how many teeth are on each gear, you can find the gear ratio relatively simply.Divide the driven gear teeth by the drive gear teeth.Depending on your assignment, you may write your answer as a decimal, a fraction, or in ratio form (i.e., x : y).

Read more

How do you grease a rear end?

This question is missing make model and year information.Any answer would be incorrect with out this

Read more

How is gear ratio calculated?

Divide the number of teeth on each "driven" gear by the number of teeth on the "drive" gear for each interlocking set of gears to calculate the intermediate gear ratios.In our example, the intermediate gear ratios are 20/7 = 2.9 and 30/20 = 1.5.

Read more

Can you sue someone for rear ending you?

The injured drivers can sue for pain and suffering, but only if their injuries are exceptionally severe.An injured driver can sue the other driver personally or his insurance company, or both! Everyone pays according to each party's degree of fault in the accident.

Read more

How do you get into the rear compartment under the rear end of the vehicle?

Not possible without cutting holes through the steel floor. With many vehicles you can gain access to the trunk by removing the rear seats.

Read more

How do you use gear ratio to increase horsepower?

It doesn't work that way. The gear ratio determines what speed the vehicle is running at when in the (torque) powerband.

Read more

How do you calculate gear ratio and torque?

Read more

How much gear oil does a 12 bolt rear end take?

12 Bolt Car differentials will take between 2-3 quarts dry for most covers.Any good name brand gear oil should be just fine.

Read more

Can you rear end someone and not be at fault?

Rear-End Collisions If someone hits you from behind, it is virtually never your fault, regardless of why you stopped.A basic rule of the road requires a vehicle to be able to stop safely if traffic is stopped ahead of it.If it cannot stop safely, the driver is not driving as safely as the person...

Read more

Can you die from a rear end collision?

Rear end accidents leave certain parts of the body especially vulnerable to injury.The neck, head, and shoulders can all be seriously harmed in a rear end collision.These injuries can affect a victim's life for years to come.The most severe rear-end collisions can result in paralysis or even death.

Read more

Can a rear end collision cause front end damage?

A clear sign that a rear-end collision has caused damage to your vehicle is issues with your trunk.While your trunk opening and closing smoothly may not seem directly impact your driving, it can have a serious impact on resale, can pose serious safety concerns, and may be a sign of other issues.

Read more

How does gear ratio use function?

gear ratio can speed up a device or slow it down. The gears that make up the gear ratio can be used to go from small to bigger thru a series of gears and slow the drive down , say 30 to 1. Or start off with large gears going smaller and speed up the drive say 1 to 30.

Read more

How do you find the gear ratio on a Dodge Ram?

Carefully count the teeth on both gears and divide the pinion number into the ring number (of teeth) and you will get a number like 3.55.That number you get will be the gear ratio.Another idea is to look at the front differential for a tag.The front would be the same ratio.

Read more

Top speed 3.42 gear ratio?

Depends on a number of factors, including tire size and corresponding revolutions per mile, final gear ratio of the transmission, and how many RPMs that engine is allowed to run. 3.42 is used both in light duty vehicles and heavy duty tractor-trailers, with different results for each.

Read more

Can a bad rear end cause vibration?

There are two major causes of vibrations: tires and wheels that are out of balance and, in rear-drive vehicles, worn u-joints.In rare instances, loose, broken, or worn suspension components can also cause a vibration.

Read more

How does insurance work if you get rear ended?

The driver who sustained damage to the rear end of his or her car is virtually never deemed to be at fault for a rear-end accident.Once you file an insurance claim for this accident, your rates will almost certainly rise.Likewise, your insurance rates could go up for matters unrelated to the rear...

Read more

Can a rear end collision damage the transmission?

it is possible to damage the transmission in a rear end collision. this is especially possible in rear wheel drive vehicles. even in a light rear end collision with a rear wheel drive vehicle can shove the drive shaft into the transmission causing serious problems.

Read more

How do you put in rear end fluid?

How to Put Gear Oil in a Rear Axle Park the vehicle and engage the emergency brake. Raise the vehicle with a jack under the axle for each side of the vehicle, if necessary. Remove the differential fill plug. Push the screwdriver into the fill hole and spin it around some. Attach one side o...

Read more

Which gear ratio is faster?

The lower the number, the faster the car will go with the same number of engine revolutions.The higher the number the better the car will accelerate, but at the expense of high speed cruising.Now for the confusing part of the story.A high numerical gear ratio is called a low gear or low rear end,...

Read more

Does gear ratio affect horsepower?

Motor HP does not change when you change gear ratios.A dynamometer measures torque and RPM, and from those two values calculates horsepower.When you change gear ratios both RPM and torque will change but horsepower will not.

Read more

What gear ratio is gu6?

GM RPO Codes – Factory Identification Labels and Interpretation RPO CodeDescriptionRatioGU3Axle Rear2.93GU4Axle Rear3.08GU5Axle Rear3.23GU6Axle Rear3.42115 more rows

Read more

How do different Differential gear ratios affect top speed?

Lower differential gear ratios, such as a 4.11 for example will help you get up to speed sooner in all gears, but your top speed will be limited vs a differential gear ratio of 3.08. In other words more torque less speed, less torque more speed. 4.11 for example means that your drive shaft from t...

Read more

How does gear ratio relate to speed and torque?

in simplest terms, gear ratio is all about leveragethe same concept that makes a larger lever able to apply more force while moving a longer distance applies to gears. instead of comparing the length of the lever, you compare the size of the gears or number of teeth (which is the same as a measur...

Read more

How much faster will it make your car by replacing the 300 rear end with a 390 rear end?

You will be quicker not faster.

Read more

How do you tell if your gears are grinding?

As noted in a previous section, with a manual transmission, a common sign of trouble is a grinding sound or feeling when you shift into a new gear.If you fully engage the clutch, shift and then hear a grinding sound, you may have a worn clutch or you may just need to have it adjusted [source: AAM...

Read more

How common are rear end collisions?

Rear-End Collisions: The Most Common Type of Auto Accident in the U.S.According to figures from the National Highway Traffic Safety Administration (NHTSA), out of the 6 million car accidents that happen on U.S.roads every year, over 40% of them (2.5 million) are rear-end collisions.

Read more

Will the rear end out of a 2003 silverado 4x4 fit a 1999 silverado 4x4and you have no idea what the gear ratios are in the 1999 someone pulled the label out of the glove box to tell you what it is?

The rears should be compatible.. as for determining what the gear ratio is, if the RPO code isn't available to you, you would have to contact the service department of any Chevrolet dealership with the VIN number of the vehicle, and they could give you the specs of the vehicle.

Read more

Is 3.73 a good gear ratio?

So, a truck with optional 3.73 gears will tow a heavier trailer than one with 3.55 or 3.21.But it will also use more fuel in all situations because the engine's rpm will be higher.Four-wheel-drive trucks will have a ratio in the front axle's differential that closely matches that of the rear axle.

Read more

Is a bigger gear ratio better?

The lower the number, the faster the car will go with the same number of engine revolutions.The higher the number the better the car will accelerate, but at the expense of high speed cruising.Now for the confusing part of the story.A high numerical gear ratio is called a low gear or low rear end,...

Read more

Which RPO code is for gear ratio?

GM RPO Codes – Factory Identification Labels and Interpretation RPO CodeDescriptionRatioGU5Axle Rear3.23GU6Axle Rear3.42GU7Axle Rear2.77GU8Axle Rear3.90115 more rows

Read more

What is the best gear ratio for towing?

So, a truck with optional 3.73 gears will tow a heavier trailer than one with 3.55 or 3.21.But it will also use more fuel in all situations because the engine's rpm will be higher.

Read more

How do I know my rear axle ratio?

Turn the wheel TWO revolutions and count the number of driveshaft turns.The number of driveshaft rotations will help you determine your rear axle ratio.For example, if it turned 3 and a half times, it's a 3.50:1 ratio.If it turned 4 and a quarter times, it's a 4.25:1 ratio.

Read more

How does gear ratio affect speed and torque?

The gear ratio expresses the ratio of the output torque to the input torque.Thus, we can multiply the torque supplied at the motor shaft (the input) by the gear ratio to find the torque at the wheel axle (the output).Transmitting power through a series of gears can also affect rotational speed.

Read more

Is gear ratio the same as mechanical advantage?

The mechanical advantage is the ratio of the number of teeth on the output gear to the number of teeth on the input gear.This ratio is the mechanical advantage of the whole gear system.Compound machines typically must overcome more friction than simple machines because they tend to have many movi...

Read more

How do you check gear ratio by spinning tire and counting pinion rotations?

Jack up the vehicle on one side. mark the drive shaft with a piece of chalk or tape a piece of string to the drive shaft, at a specific location, say at the point closest to the ground. Also mark the tire as well so that you can determine exactly how many revolutions you turn the wheel. If you do...

Read more

What is the calculation of the gear ratio?

Calculating the gear ratio for a car entails a lot of information. How high do you want the car engine to rev(turn-RPM) at 60 MPH? How much horsepower is the engine making and how much can be developed at the rear wheels?(I am assuming you're are referring to a rear wheel drive vehicle). How Much...

Read more

What is the towing capacity of a 92 GMC K1500 5.7 3.42 rear end gear with 700R4 trans?

Stay under 5,000 lbs. with that combination.

Read more

What damage can a rear end collision cause?

One commonly missed type of auto collision damage sustained during rear-end collisions involves the bumper cover.In many vehicles, the bumper is plastic and doesn't provide a great deal of protection.During a rear-end collision, even a minor bump can cause damage to the frame behind the bumper.

Read more

Can a rear end collision also cause damage to transmission?

In an all-wheel or rear-wheel drive vehicle, the driveshaft runs from the rear axle to the rear of the transmission.If the vehicle is hit from behind in an accident, the force of impact may bend or push the driveshaft into the rear of the transmission.This could cause damage to the transmission, ...

Read more

How full do you fill the rear end in an 1987 EZGO golf cart?

As soon as lube runs out of the fill hole, it is full.

Read more

How do you identify the rear end of a 2005 ram 1500?

It is a chyrsler 9.25, has a diff cover that looks like a stop sign(octagon) and has 12 diff. cover bolts.

Read more

Are you always at fault if you rear end someone?

Rear-end collisions are one of the most common types of accidents.If a car hits you from behind, it'll almost never be your fault, even if you were stopped.One basic driving rule is that you're supposed to leave enough room in front of your car to stop when the car in front of you stops suddenly.

Read more

Are you automatically at fault if you rear end someone?

If You Rear-End Someone, Are You Automatically At Fault? In general, the driver who rear-ends another vehicle is held responsible for the accident due to negligence on their behalf.This is not always the case, however, so we'll look at a few guidelines for determining who is at fault for an accid...

Read more

Can you just change the gear on rear window of a 1989 ford bronco?

No, the gears are stamped as part of the regulator arms. If the gears are bad the regulator unit would need replaced. More likely a problem with the gear on the motor. I've never seen the motor gear offered separately. Motor would have to be replaced.

Read more

Chevy s10 5 speed transmission gear ratios?

Chevrolet S 10 five-speed transmission gear ratio is; first gear 1.15, second gear 1.63, third-year 2.37, and the drive gear 2.81. Chevrolet does offer optional gear ratios.I think those numbers above are backwards. It should look something more like this.For the type MW2 5 speed, 1st: 3.96, 2nd:...

Read more

Will bigger tires affect gear ratio?

good point, this also effects your odometer.A bigger than stock rolling diameter slows the rate miles are accumulated, whereas a smaller than stock rolling diameter accumulates miles faster.tires will not change any gear ratio a gear ratio is just that, a ratio of the size of the driving gear to ...

Read more

What does a 4.10 gear ratio mean?

When you hear people refer to numbers like 3.08, 3.73, or 4.10, they're talking about the ratio of the ring-and-pinion gears in the rear axle—hence, the numbers are more accurately 3.08:1, 3.73:1, or 4.10:1.That also means that for every one turn of the ring gear, the pinion will turn 4.11 times.

Read more

What gear ratio is best for towing?

The most popular rear end ratio in trucks today is the 3:55, which sort of averages towing power and fuel economy.This is a good ratio for the occasional towing or hauling individual.For a person who tows more often, and heavier loads, the 3:73 or 4:10 may be more appropriate.

Read more

Can a rear end collision total a car?

Rear end collisions are the most common, and will likely leave you and your vehicle in some pain.This rear end collision may total your car and will likely cause some injury, but what actually happens in a rear end collision shows us just how deadly the automobile can be.

Read more

Can a rear end collision cause electrical problems?

Motor damage will not result from a rear-end collision, but there are damages that can impact your car's drivetrain.The impact can shove the exhaust system forward, which can then cause damage to the exhaust manifold, catalytic converter, engine mounts, or a "Y" pipe which runs into your car's en...

Read more

What damage can be caused by a rear end collision?

One commonly missed type of auto collision damage sustained during rear-end collisions involves the bumper cover.In many vehicles, the bumper is plastic and doesn't provide a great deal of protection.During a rear-end collision, even a minor bump can cause damage to the frame behind the bumper.

Read more

Whats the Gear ratios for a 72 challenger?

The 72 Challenger had 3 different gear ratios depending on the motor the car came with. If the car came with the 225 or 318 cu. in. motor it had 2.76 or 3.23 gears in the rear end. If it was a Rallye Car with the 340 cu.in. motor it had the 3.23 or 3.55 gears. The approximate ratio can be determi...

Read more

What is the difference between 3.73 and 4.10 gear ratio?

What is the difference between a 3.73 gear ratio and 4.10? The ratio is the number of teeth on the driven gear (ring) divided by the number of teeth on the drive gear (pinion).So, if the ring gear has 37 teeth and the pinion has 9 teeth, the ratio is 4.11:1.

Read more

Can a rear end collision cause frame damage?

Even during a light impact rear end collision the damage to your vehicle can be devastating.A rear end collision is felt through the entire vehicle and can cause structural damaged in other parts of the vehicle that may be over looked or missed upon safety inspections.

Read more

How much gear oil goes in the rear axle?

5 quartz depending if it come out of the differentals

Read more

Is a higher gear ratio faster?

Gear ratios can be boiled down to a single statement: Higher ratios (with a lower numerical value) give better torque/acceleration and lower ratios allow for higher top speeds and better fuel economy.Higher ratios mean the engine has to run faster to achieve a given speed.

Read more

Is a 4.10 gear ratio good?

It may help if you read the “Gearing Lingo” in the right column first.When you hear people refer to numbers like 3.08, 3.73, or 4.10, they're talking about the ratio of the ring-and-pinion gears in the rear axle—hence, the numbers are more accurately 3.08:1, 3.73:1, or 4.10:1.

Read more

What does changing your gear ratio do?

Having the correct gear ratio for your truck and its tires will give you the best fuel economy, improve acceleration, throttle response, and your ability to maintain highway speeds.When changing gears for taller tires, you are heading to a numerically higher gear ratio.

Read more

What is the gear ratio on a 1996 GMC 1500?

You would need to look at the RPO codes on the sticker in the glove compartment. If it's a 4x4, you most likely have either 3.73 (GT4) or 4.10 (GT5) ratios. 3.08 (GU4), 3.42 (GU6), and 3.55 (GV0) are also seen sometimes. The best way to know for sure is to call the service department of a GMC dea...

Read more

What is the gear ratio of a Turbo 350?

Typical Transmission Ratios Transmission1st2ndPowerglide1.821.00Turbo 3502.521.52Turbo 4002.481.48700R43.061.639 more rows

Read more

How can i find out the front gear ratio on a 1999 Chevy Tahoe four wheel drive?

It'll be the same as the rear. If you don't know what that is, you'll have a list of RPO codes in the glove compartment. Do a search for "GM RPO codes", and you'll have multiple sources that'll provide you lists to compare to what you see on that sticker. This is, of course, assuming that you sti...

Read more

Swap 52 Chevy truck rear end with 54 Chevy powerglide rear end?

the '52 should have a 4.11:1 ratio in it currently. If you change it out for the '54 rear end you will have a 3.55:1 ratio. As far as changing it, it should bolt right up. Do you have a more specific question?

Read more

Can you put a 4th gen firebird rear end on a 4th gen camaro?

It should, but may be a tad wider

Read more

What kind of injuries can you get from a rear end collision?

Some of the most common injuries that Rear-End Car Accident Victims suffer from are; Whiplash: Whiplash is the most commonly-cited injury from a rear-end collision. Back Injuries: Spinal Cord Paralysis: Head and Brain Injuries: Facial Disfigurement: Wrist and Arm Injuries: Seat Belt Inj...

Read more

What is different between a 8.5 rear end and a 8.6 rear end?

The numbers 8.5 and 8.6 in this case refer to axles. The only major difference between the two is the width of the carrier bearings, which itself connects to a device known as a differential case, which not only protects the axle from the bearing, but also drives a number of gears in the mechanisms.

Read more

What happens if you rear ended someone without insurance?

Also, there will be an additional fine for driving without insurance.Doesn't really matter; if you rear end the person, you are almost certainly at fault, and you or your insurance company will pay for the other guy's damages and injury.EXACTLY the same as would happen if the other driver DID hav...

Read more

What is posi rear end?

Posi is short for "Positraction".A limited-slip differential is a type of diferential that is intended to spin both wheels if the speed difference between them becomes too great.This is beneficial when taking off in slippery conditions.

Read more

What do you do after a rear end collision?

What to Do After the Car Accident.If you are involved in a rear-end collision, contact the police, take photographs of the accident scene and of both vehicles, get witness information (names and contact information), fill out a report if the police do not come to the scene, and call your insuranc...

Read more

What do you do when someone rear ends your car?

What to Do When You're Rear-Ended Take a deep breath, and don't panic.Check for injuries. Seek medical attention for those injured.Call the police and report the accident.Take pictures and document the positions of the vehicles. Get a copy of the accident report.Contact your insurance company.

Read more

Who's at fault if you get rear ended?

Rear-End Collisions If someone hits you from behind, it is virtually never your fault, regardless of why you stopped.A basic rule of the road requires a vehicle to be able to stop safely if traffic is stopped ahead of it.If it cannot stop safely, the driver is not driving as safely as the person...

Read more

What do you do if someone rear ends your car?

What to Do If You Rear-End Another Car Take a deep breath. Don't panic and do not flee the scene of the accident.Check for injuries. Call the police and report the accident.Take pictures and document the positions of the vehicles. Get a copy of the accident report.Contact your insurance com...

Read more

How wide is a Chevy 10 bolt rear end?

The 10-bolt can handle just about anything you throw at it, as long as you use the right axle, either the 8.5- or 8.6-inch.That is the great caveat; there are four sizes of 10-bolt GM rear ends: 7.5/7.625-, 8.2-, 8.5-, and 8.6-inch.

Read more

How do I know what size rear end I have?

Measure the diameter of the ring gear.This measurement equals the size of your rear end.Count how many bolts are on the inspection cover.If you have 10 bolts, then your Ford has a 7.5-inch or an 8.8-inch rear end.

Read more

How much does a rear end collision cost?

Less than one-third of accidents include injuries.A general rule of thumb is to multiply the direct costs by 1.5 to 4 to come up with the total settlement costs.For example, if you had $1,000 in direct costs, your total settlement would range between $2,500 to $5,000 using this range.

Read more

How do you tell what gear you have with out tacking off cover?

Rear differential.: Jack up car, place in neutral, rotate both tires one revolution forward while counting the revolutions the drive shaft makes.With care full counting and measurement of the partial revolution at the end you will end up with a good idea what the ratio is.

Read more

How do I know what rear end I have?

Read more

How much is a rear end accident worth?

Less than one-third of accidents include injuries.A general rule of thumb is to multiply the direct costs by 1.5 to 4 to come up with the total settlement costs.For example, if you had $1,000 in direct costs, your total settlement would range between $2,500 to $5,000 using this range.

Read more

How to Change drive shaft between motor and rear end?

1 put car in neutrol 2 put e brake on 3 drain transmission fluid 4 unbolt drive shaft from rear end pull shaft out or if your car is newer 2005 have a shop take care of it

Read more

How do I identify my Chevy rear end?

Casting codes can also be used to identify the manufacture date. Count the number of inspection cover bolts on the rear end housing. Identify the most common GM rear-end types. Look at the shape of the inspection cover and the gasket. Locate the GM manufactured rear-end casting date on the...

Read more

How wide is a Ford 8.8 rear end?

The cover is not quite square, measuring about 10 1/2 inches high by 11 inches long (the 7 1/2-inch rear end uses a cover that measures 10 9/16 inches square).The pinion shaft is 1 5/8 inches and has a 30-spline count.

Read more

How long does a rear end collision settlement take?

That usually becomes clear within the first 30 to 90 days after an accident, during which time settlement would be likely.That means the insurance company representing the at-fault driver writes a settlement check to the injured person, who in turn signs a release giving up any future right to su...

Read more

How do headrests help against rear end shunts?

The headrest prevents the head from being thrown backwards (and damaging the neck) - and injury called whiplash, when a vehicle is hit from the rear.

Read more