Do struts need to be greased?

struts/shocks are designed to be self-lubricating.

DO not introduce any foreign grease/lubricant that may get into the oil and upset it's chemical composition.

Try keeping your strut/shock shaft dirt-free is the only way to go.

Previous questionWhich SUVs hold their value best?
Next questionHow fast is 34 km in mph?

Related question

Do cars need to be greased?

If yes, which parts would get greased? All cars need periodic oil and filter changes, usually every 3000-5000 miles.Modern cars do not have grease points and all those joints are permanently lubricated.

Read more

Why would strut bearing plates need to be replaced?

They can wear out and make crunching noises especially when dirt gets into them.

Read more

Do you need to grease wheel bearings?

When to Grease Your Bearings If you only go on a few short trips every year, then you probably don't need to have those wheel bearings greased every season.On the other hand, if you travel frequently in your RV and rack up a lot of miles while doing so, then you may need to have it done more tha...

Read more

Need to replace all 4 struts on minivan how much?

Struts can cost anywhere from $25 to $350 each, depending on the make, model, and size of your vehicle. Depending on which mechanic you go to, it can take about four to five hours to replace all of the struts on your vehicle. Mechanics charge an average of $50 to $120 per hour which would put you...

Read more

How do you know you need new shocks and struts?

the_front_end_of_the_vechicle_will_ethier_allow_the_front_to_droop_and_it_will_also_end_up_being_stiffer in_the_ride.Another_way_is_too_bounce_the_car_by_hand_watching_for_the_number_of_bounces_that_it_takes more_than_two_is_considered_sloppy_and_in_need_of_replacement.

Read more

How do I know if I need shocks or struts?

Read more

Why do you need a grease gun for a tractor?

A tractor has numerous fittings which require grease to maintain the proper lubricationto moving joints. No lube and the fitting will either lock up or waer out much faster.

Read more

Can grease fittings be added to 2005 Jeep Liberty?

Aftermarket replacement parts will come with grease fittings such as tie rod ends, ball joints, etc.

Read more

Do new struts have to break in?

For the first hundred or so miles after installing your new gear, the driver will notice that the suspension feels a little stiff and bouncy.This is normal and happens primarily for two reasons: First, a new set of shocks and struts needs to be broken in just like anything else.

Read more

Do lug nuts need to be torqued?

Lug nuts must be torqued to the manufacturer's recommended values, and they must be re-torqued to those values after driving approximately 50 to 100 miles on your new tires after the tire service.Both under and over tightening can be dangerous.To tighten lug nuts correctly, a torque wrench is req...

Read more

Do shocks need to be broken in?

The shock however, will begin working normally after several strokes or as the vehicle begins driving.Again, shock priming is not required, but it's quick and easy and can help reduce any “break-in period” for your new shocks.

Read more

Do modern cars need to be waxed?

CARS.COM — How often do you need to wax your car? This is easy to remember no matter your level of auto adeptness: If your vehicle is usually parked in a garage or otherwise sheltered from the elements, waxing it twice a year should be enough to protect the paint finish.

Read more

Do scooters need to be registered?

In Arizona, scooters are categorized as either motor-driven cycles or regular motorcycles.You still need a motorcycle license to drive a motor scooter on Arizona roads, regardless of how powerful its engine is, and you must register your vehicle with the Arizona Motor Vehicle Division.

Read more

Do tow dollies need to be registered?

License Requirments for Tow Dollies In many states a tow dolly does not need to be licensed and tagged, but many require that the tow dolly be titled and registered.The car being towed must be licensed as its wheels come into contact with the pavement.

Read more

Why do cars need to be painted?

To protect the metal from rust on a steel car. On an aluminum, or carbon fiber car it is not necessary to paint the car. As an example all DeLorean's were not painted from the factory as the body panels were made of aluminum.

Read more

Do new cars need to be inspected?

Each vehicle registered in New York State must be inspected at least every 12 months.You are not required to have your vehicle repaired or re-inspected at the station that performed the initial inspection.

Read more

Do timing chains need to be replaced?

A timing chain runs inside the engine, as it needs to be lubricated by the engine oil.A timing belt typically needs to be replaced between 40,000 and 100,000 miles depending on the vehicle and it's a few hundred dollar repair.A timing chain doesn't need to be replaced unless there is a problem wi...

Read more

Do joint accounts need to be probated?

Joint Accounts Probate of this type of joint account simply won't be necessary.Instead, all that the surviving owners will need to do is show the bank or investment company a death certificate for the deceased owner, and then the deceased owner's name can be removed from the account.

Read more

Why do batteries need to be replaced?

because they run out of energy

Read more

Do commercial vehicles need to be inspected?

Federal safety regulations require that commercial motor vehicles operating in interstate or foreign commerce must pass an inspection at least annually.

Read more

Why do outlets need to be grounded?

The idea behind grounding is to protect the people who use metal-encased appliances from electric shock.The casing is connected directly to the ground prong.With the case grounded, the electricity from the hot wire flows straight to ground, and this trips the breaker in the breaker box.

Read more

Why do bolts need to be torqued?

When such a bolted joint is tightened further, a torque is applied to the nut which, (after the initial friction is overcome), causes the nut to turn and stretch the bolt.The body of the bolt acts like a stiff spring.The stretching of the bolt causes a predictable preload to exist in the bolted j...

Read more

Why do organisms need to be classified?

All living things are organized into groups by scientists as they are identified.Different scientists use various systems of classification to organize all living things into groups.Overall, the reason scientists classify living things is to understand the relationships between different organisms.

Read more

What do you need to be able to use GPS?

All you need is a GPS receiver from companies like Garmin, Tomtom etc.

Read more

Can the standard shifter be greased?

yes you can grease a standard shifter.

Read more

How do you change grease in a grease gun?

you buy a new tube of grease and put it in the grease gun

Read more

Is die electric grease needed at distributor contacts?

No, dielectric grease is to provide insulation from corrosion on electrical contact points. It is normally used in lamp sockets and electrical plug in connectors that are subject to some exposure to the elements. The intent of distributor contact points is to intermittently conduct electricity. T...

Read more

Grease guns are used to insert grease into?

A grease gun is used to force grease through a grease nipple, and so protect moving parts in a vehicle (for instance) from excessive wear.

Read more

Can the air suspension on a 96 continental be changed to a regular strut?

Yes.Many auto parts stores sell a conversion kit.It's possible, but may not be particularly cost effective, especially for a vehicle of such age.

Read more

Do handicap vehicles need to be special ordered?

In most cases I think you should special order to how you want it, but a few body shops that are listed and licensed for medical mechanical approved adjustments can just modify an existing vehicle. Unless there are special measurements then it would be best to special order.

Read more

What skills do you need to be a defensive end?

You need to be good a tackling if you want to be a defensive end. You also need to be able to work your team mates.

Read more

How often do car engines need to be replaced?

If a modern fuel injected engine is serviced and maintained according to the maintenance schedule listed in the owner's manual and only quality OEM type parts are used it can easily last 200,000 or more miles without any major problems. When it does need a major overhaul you can have the engine r...

Read more

How often do commercial vehicles need to be inspected?

Every commercial vehicle, including each segment of a combination vehicle requires periodic inspection that must be performed at least once every 12 months.

Read more

How often do rear brakes need to be replaced?

How to tell if your brakes need replacing.Generally, brake pads need to be replaced after about 50,000 miles.Some need to be replaced after 25,000, while others can last for 70,000 miles – it all depends on the factors listed above.

Read more

Do diesel gas tanks need to be vented?

Gasoline fuel tanks are required in many places to have breathing vents which retain vapors for vapor recovery systems.Diesel tanks for emergency generators do not have this requirement and are typically open to the atmosphere.The tank vent is required to disperse vapors that are discharged from ...

Read more

Do new brake rotors need to be machined?

It has often been said that you should never machine new rotors, but in some cases, a new rotor should be machined to match the vehicle with an on-the-car brake lathe.The main advantage of these lathes is that they are able to cut a rotor in its operating plane.This means that the rotor is machin...

Read more

Why do lug nuts need to be Retorqued?

Re-torquing the wheels involves tightening the lug nuts to help ensure they're not too tight or too loose.Too tight, and the nuts can damage bolt threads, break fasteners or warp new rotors.Too loose, and your wheel could fall off when you're driving.

Read more

Do you need a license to be a repo man?

In order to become a repo man (or woman), you'll need to: Learn about your state's licensing regulations and other state laws related to repossession.Obtain the necessary licenses.Obtain a driver or a truck (a tow truck if you plan to repossess cars).

Read more

What subjects do you need to be a mechanic?

Automotive mechanic programs include courses like general mechanics, engine reconditioning, automotive brakes, steering and suspension, air conditioning, and standard transmissions.After finishing required course work, you will be placed in an internship or apprenticeship, to gain experience in a...

Read more

How do I know if bushings need to be replaced?

Typical tell-tale signs of worn bushings under a vehicle include the following symptoms: The vehicle makes rattling noises when driven over gravelly roads.The vehicle sounds as though it is clunking when you make sharp turns or hit the brakes.The vehicle feels as though it is trembling along ...

Read more

How often do starters need to be replaced?

As a rule of thumb, you can expect about 80,000 starts from a brand new starter with no defects.Starters in warmer climates will typically last longer also, which is why car trouble is more likely on the worst day of the year when you need your car the most.

Read more

What education do you need to be a car designer?

Most employers require automobile designers to earn at least a bachelor's degree in engineering, industrial design, transportation design, or mechanical engineering with an automotive design concentration.

Read more

What degree do you need to be a auto mechanic?

Degrees are far to theoretical to be applied directly to the problem of auto repairs. Most car mechanics learn through on-the-job training such as apprenticeships.

Read more

Why do lorries some lorries need to be earthed?

because of static electriciry.lorries carrying certain chemicals,petrol,gas and aviation fuel must be earthed and the drivers must hold a hazchem license to carry these products.

Read more

What do you need to be a truck driver?

First, training. Second, you need to be able to pass a physical exam and a drug test. Third, you must be able to read, write, and speak English. Fourth, you must have a CDL. Last, you must be willing to spend long periods of time away from home and family.

Read more

What skills do you need to be a car engineer?

Math, science- physics, chemist, computer science and art would also be a plus.

Read more

What qualifications do you need to be a automotive engeer?

Generally you will need A level Maths and Physics at B or above. Some courses do vary though. You may also need to learn how to spell engineer

Read more

What education do you need to be a automotive engineer?

An automotive engineer's career training begins with a four-year bachelor's degree from an accredited college or university.This is generally the basic requirement for entry-level jobs in the career.

Read more

Do all 4 tires need to be balanced?

If it is not, he will attach small lead weights to the rim of the wheel to ensure that they are balanced.Most manufacturers recommend that all four tires should be rotated and balanced approximately every seven thousand miles.Typically, tread wears away quicker on the front tires than on the back...

Read more

How often do electric car batteries need to be replaced?

Most new car batteries are designed to last over 300,000 miles.This can take 15 — 20 years for a household car with average 50 miles a day.So literally you are not replacing the battery for the lifetime of the car.However, for commercial vehicles, this can be just about 2 to 3 years.

Read more

Do Toyota timing chains need to be replaced?

A timing chain runs inside the engine, as it needs to be lubricated by the engine oil.A timing belt typically needs to be replaced between 40,000 and 100,000 miles depending on the vehicle and it's a few hundred dollar repair.A timing chain doesn't need to be replaced unless there is a problem wi...

Read more

Do wheel bearings need to be replaced in pairs?

You should replace your hub assembly and wheel bearings.Here's how to replace wheel bearings.Even if only one side is bad, it makes sense to replace them in pairs.Typically, a hub assembly that is worn out will be hotter than the other hub assemblies on the vehicle.

Read more

What license do you need to be a mechanic?

You need a repair licence to open a repair shop. You don't need a licence to be a mechanic but, it would be to your benefit to be a certified mechanic.

Read more

Why do Valves keep needing to be adjusted?

Depending on the vehicle there are many wear points involved. There is wear at the valve seats, valve guides, valve stem, rocker arm to valve, rocker arm to pushrod, pushrod to lifter, lifter to camshaft and cam shaft. Some of these are eliminated if you have a overhead camshaft type engine. As t...

Read more

What do you need to be a car engineer?

First you need to understand the basic mechanics which enables the automobile to function. The list of functional theory mentioned below has to be understood, through practical knowledge (i.e) hands on experience.1. Thermodynamics2. Engineering Mechanics (Static and Dynamic)

Read more

How often do motor mounts need to be replaced?

In general, motor mounts do not have a scheduled replacement but should last between 5 to 10 years before dry rot or breaking from age-related failure.Motor mounts can get broken from slamming the vehicle, gears over-revving, and letting out clutch or power braking the engine before takeoff.

Read more

How often do brake rotors need to be replaced?

First rotors are a disposable items and will need replacing anywhere from 15,000 to 70,000 miles into their use depending on your driving style and the type of brake pads used.Some brake pads are much more aggressive than others.A sign of a fairly aggressive pad is one which makes a lot of dust.

Read more

Do you need a license to be a courier?

Get a license for your courier service before starting your business.A license provides legal authority for the business to operate within the city, county and state boundaries.A courier service may require both a business license and a driving license, depending on your location and businesses y...

Read more

What qualifications do you need to be a car painter?

Education Requirements You need to have at least a high school diploma to qualify for most automotive painting jobs.Increasingly, transportation equipment painters go through postsecondary training programs at community and technical colleges.

Read more

Do you need good grades to be a lawyer?

As early as high school, aspiring lawyers should begin planning for their academic future.To gain acceptance into a good college -- which will be integral to getting into a good law school later on -- students must maintain a high GPA.Anything above a 3.5 is ideal.

Read more

How often do wheel bearings need to be replaced?

Typically, you should check and maintain your wheel bearings every 25,000 to 30,000 miles.An average sealed wheel bearing lasts 85,000 to 100,000 miles although some can last as long as 150,000 miles.

Read more

How often do gas cylinders need to be tested?

Usually, cylinders must be retested or inspected every five or ten years.The date of each test must be stamped on the cylinder.

Read more

Do caravans need to be kept on level ground?

As with all vehicles, only to get a correct fluid level reading.

Read more

Do all wheel tires need to be rotated?

This reason alone is why regular tire rotation is necessary.For front-wheel drive vehicles, the Forward-X rotation is recommended.For rear-wheel drive vehicles, the Rearward-X or X-rotation is best.Front-to-rear rotation is applicable for directional tread patterns with the same size front and rear.

Read more

What skills do you need to be a car salesman?

The top skills recruiters look for in car sales executives Sales and negotiation. The clue is in the name, sales and negotiation skills are obviously a vital aspect to the role of a car sales executive. Understanding of financials. Verbal communication. Customer service. Resilience.

Read more

Do I need special insurance to be a delivery driver?

For most takeaways it's essential that their delivery drivers have their own vehicle to use.To be properly covered and work within the law, you will need to ensure that you have fast food delivery driver insurance.Hot food delivery insurance is a special form of hire and reward insurance.

Read more

Do tire pressure sensors need to be replaced?

Tire pressure monitoring systems include sensors that are mounted on the wheels or on valve stems, and the tire pressure sensors can wear out or be damaged by potholes, debris or the weather and need replacing.On many vehicles, the TPMS needs to be electronically reset after changing or replacing...

Read more

Do you need a license to be a car broker?

Though specific requirements vary from state to state, to obtain a license to operate as an auto broker you must secure an appropriate location, register your business with state authorities and purchase sufficient insurance and bonding.Remember to obtain a dealer license application packet durin...

Read more

What qualifications do you need to be car mechanic?

mechanis degree, smart head on your shoulders, and most of all know what you are doing.

Read more

What do you need to be a car designer?

It's a common predicament. You're 16 years old and desperate to become a car designer but have little idea about how to achieve that burning ambition. Well, discovering Car Design News is a good start, but if you're serious about training as a designer to work in a major car studio then you need ...

Read more

Do cars need to be warmed up before they're driven?

It all depends on what kind of driving you plan on doing if you are trying to go 0 - 60 i would recomend warmining it up. If it is winter most people warm up their cars so it's not like an ice box!

Read more

Do you need a CDL to be a delivery driver?

Most places hiring delivery drivers require a high school education, a valid driver's license and a clean driving record.However, if you'd like to drive heavy trucks or tractor trailers, you'll need your CDL (commercial driver's license) and will need to attend special classes.

Read more

What qualifications do you need to be a car detailer?

Step 1: Take some automotive classes.You don't need a master's degree or a college education to become a car detailer.However, you should have a high school diploma, and some experience working with cars.

Read more

How long do anchor bolts need to be?

The bolts are required to be embedded a minimum 7" into the concrete, so standard length bolts aren''t long enough.

Read more

How deep do concrete anchors need to be?

The hole needs to be drilled a minimum of 1/2” deeper than the anchor will penetrate the concrete.Each diameter anchor has a minimum embedment for installation to allow the anchor to achieve its minimum holding values.

Read more

What qualifications do you need to be a car mechanic?

While a high school diploma is the minimum education requirement for mechanics, many employers prefer to hire those who have completed certificate or associate's programs in automotive technology or related fields.Mechanics can earn voluntary certification to enhance job opportunities.

Read more

Do car air conditioners need to be recharged?

There's no service or maintenance schedule here – you don't need to recharge your air conditioning system every year, or even every two years.The best indicator that you need to recharge the refrigerant is when the system begins to cool less than it used to, but before it stops cooling completely.

Read more

Do tires need to be replaced in pairs?

Tires should be replaced in pairs, both in the front, or both in the back.If your vehicle is an all time all wheel drive, manufacturers recommend replacing all four tires to keep the rotations per mile uniform.It's also recommended that new tires go on the rear.You want to change brand or model o...

Read more

How often do timing belts need to be replaced?

Many car owners may wonder how often to replace a timing belt.The old rule was every 60,000 miles.As technology has improved, many manufacturers recommend intervals up to 100,000 miles.To be safe you should check what the vehicle's manufacturer recommends and stay within that mileage.

Read more

Where do L plates need to be displayed?

L plate regulations They should be visible from both the front and rear, meaning you will need to display at least two on your vehicle.L plates should only be displayed while a learner is driving the vehicle.

Read more

What degree do you need to be an automotive designer?

The minimum requirement for most auto design jobs is a bachelor's degree in a related field, although some designers have master's degrees.

Read more

Why do some lorries need to be earthed?

Lorries that transport inflammable liquids, gases and powders must be earthed. This is because when a lorry drives along the road the rubbing of it's tires against the tarmac creates an electrostatic charge build up on the metal chassis of the vehicle. When unloading the load from the lorry this ...

Read more

Do you need to be advised it's a salvage car?

When buying the salvage vehicle, ensure that you search the history of the vehicle.

Read more

What degree do you need to be a truck driver?

No Degree, but You do need a CDL (commercial driver's license) which classs depends on what you are transporting/Class of truck. There are CDLs - A, B, C. A is for Semi trucks 80,000GVW. I think CDL C is for like school bus driver's.

Read more

How often do fusible links need to be replaced?

All Fusible Links shall be replaced once a year.The Links shall be replaced sooner during annual inspection if the conditions in (4) exist.The Fusible alloy that is used in the manufacturing of the Fusible Links undergoes a phenomenon known as Creep or Cold flow.

Read more

What skills do you need to be an automotive engineer?

To become an automotive engineer, you will need: effective technical and problem-solving skills.commercial awareness.good attention to detail.creativity.interpersonal and communication skills.presentation skills.the ability to work as part of a team.

Read more

Do you need a license to be a car salesman?

The requirements to get a car salesman license in the states that require them are all very different.Depending on the state the fees are all over the board.The states that do not require you to have a license to sell cars require the dealerships where you work to have a car dealers license.

Read more

How many feet do tail lights need to be visible?

Tail lights must be visible for 500 feet.6.Headlights must illuminate persons and objects for 350 feet on high beam and 100 feet on low beam.

Read more

Do you need a license to be a mechanic?

In a word, yes.Rules vary from state to state, but with the exception of a few outliers such as Texas, auto mechanics are required to carry not one but several licenses to operate.In addition, many states require mechanics to obtain a state business license specifically to run a repair shop.

Read more

Do oxygen sensors need to be replaced in pairs?

Do I need to replace all of my oxygen sensors at once? It is best to replace your sensors in pairs.However, on most vehicles produced since 1996, replacing one sensor (especially the front engine monitoring sensor) will cause the ECU to set a code for the other sensors.

Read more

Do Honda timing chains need to be replaced?

A timing chain runs inside the engine, as it needs to be lubricated by the engine oil.A timing belt typically needs to be replaced between 40,000 and 100,000 miles depending on the vehicle and it's a few hundred dollar repair.A timing chain doesn't need to be replaced unless there is a problem wi...

Read more

What GCSEs do you need to be an automotive engineer?

You'll usually need: 4 or 5 GCSEs at grades 9 to 4 (A* to C) and college qualifications like A levels for a degree apprenticeship.

Read more

Do older cars need to be inspected in NJ?

Beginning May 1, the New Jersey Motor Vehicle Commission (NJMVC) will change the inspection requirements for certain older passenger vehicles, which will no longer have to undergo tailpipe emission testing.

Read more

How much do front struts cost to replace?

Know what price you should pay to get your vehicle fixed.The average cost for a suspension shock or strut assembly replacement is between $1,342 and $1,440.Labor costs are estimated between $134 and $170 while parts are priced between $1208 and $1270.Estimate does not include taxes and fees.

Read more

How do you measure gas struts to replace?

Read more

Do you have to grease new ball joints?

Many ball joints are sealed these days and do not come with grease zerk fittings.Theoretically, these ball joints will not need any extra grease and are sealed up tight so contaminates can't get inside, but if you notice a groaning while turning then the culprit might be a grease-thirsty ball joint.

Read more

What size tip do you use on a grease gun to grease the ball joints on a 2002 Chevy 1500?

It takes a standard Zerk fitting. If your having trouble with the Alemite fitting on the end of the grease gun, it may be worn out or just loose.

Read more

How often should shocks and struts be replaced?

Like all automotive parts, your vehicle's shocks and struts follow a specific maintenance schedule.Experts say that shocks and struts should be replaced every 50,000 to 100,000 miles.However, that's just a general recommendation.

Read more

What do struts sound like?

They should make no noise.

Read more

What do you need to do to be a truck driver?

Before joining the industry as a professional truck driver, there are a few requirements to become a truck driver that you'll need to meet. Obtain a CDL. Attend a Truck Driving School. Clean Driving Record & Solid Work History. Be at Least 21 Years Old. Pass a Drug & Alcohol Test ...

Read more