Can you put a serpentine belt on backwards?

you actually can put a belt on backwards.

grooves go to grooves, and smooth goes to smooth.

but you have to pay close attention to the belt routing diagram.

if the belt is put on the wrong way it can spin the water pump reversed causing an overheat condition very fast after starting.

Previous questionHow much do shredding companies charge?
Next questionDoes parking on a hill damage your brakes?

Related question

Can a serpentine belt be put on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

What happens if you put a serpentine belt on wrong?

REPLACING A SERPENTINE BELT.In some instances it may be possible to install a serpentine belt the wrong way.If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump.This can cause major pr...

Read more

Can you replace a serpentine belt yourself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

Do you have a diagram of how to put the serpentine belt on the pulley?

You may get an answer if you list the vehicle & engine you are talking about. You are not going to get an answer to this question as is.

Read more

Can you put a thermostat in backwards?

If you installed the thermostat backwards, it would probably not open up enough to allow coolant to flow, and the temp gauge would shoot up into the far right range, the engine would overheat, etc.etc.So the overflow tank provides a way for the engine to only have as much coolant as it needs.

Read more

Can you drive without serpentine belt?

Since the serpentine belt is generally the only accessory drive belt on vehicles these days, this is what you'll lose: Engine cooling* - The serpentine belt drives the water pump.Without the water pump, there will be insufficient coolant flow to maintain engine temperature, and you will overheat ...

Read more

Can you drive a car with a broken serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Can you drive a car with a bad serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Can you drive with a bad serpentine belt?

This is all because many cars have one serpentine belt that drives the water pump, the power steering pump, the alternator and the air conditioning compressor, and the fan.Some cars have an electric fan.It is best to not drive a car with a broken belt, even for a short distance.

Read more

Can you drive a car without a serpentine belt?

As you can see, driving without a serpentine belt is not an option, at least not for very long.*Some cars have an electric water pump and/or electric assist steering.

Read more

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

Can I change a serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How do you replace serpentine belt on a fx 35?

1. Remove front engine undercover.2. Loosen idler pulley (alternator and power steering oil pump belt) lock nut and adjust tension by turning bolt.3. Same is done for the other idlery pulley (A/C compressor belt).

Read more

How can you bypass a serpentine belt on a 2002 converible sebring from the ac compressor?

You realy can't. If your intention is not to power the A/C unplug the wire that connects to the electric clutch. It should be right behind the pully.

Read more

Can I drive without a serpentine belt?

As you can see, driving without a serpentine belt is not an option, at least not for very long.*Some cars have an electric water pump and/or electric assist steering.

Read more

What happens if you put a battery charger on backwards?

Battery Damage If you reverse the polarity of the charger to the battery, the battery may explode.It may also cause the battery to stop holding a charge permanently.When a battery is damaged, you need to dispose of it properly, as it could leak acid.

Read more

How do you change a serpentine belt?

How to Replace a Serpentine Belt Take a good look at both your repair manual and your belt routing diagram under the hood before beginning. Look at the way the old belt wraps around the pulleys. Locate the self-adjusting tensioner and know that you need to be careful when releasing tension ...

Read more

What happens if you put a fuel filter on backwards?

Worse than performance problems, a fuel filter that was installed backward may cause problems that do not produce noticeable symptoms.A backward fuel filter may restrict fuel to the engine, but the restriction is made up by the fuel pump.This will result in increased wear to the fuel pump and may...

Read more

How do you remove serpentine belt on 2005 Chevy Cobalt?

You have to release the stress in the tensioners to remove the serpentine belt. When you put it back on there is a diagram under the hood of the car that takes you step by step.

Read more

How do you replace serpentine belt on 2005 Equinox?

Begin by loosening the tensioner pulley on your 2005 Chevrolet Equinox. The serpentine belt will become loose and can be removed. Reverse the process to install your new serpentine belt.

Read more

Can I change my serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

Can I replace serpentine belt myself?

Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning.Just rotate the tensioner, remove the old belt and install a new one.

Read more

How long can a car drive without a serpentine belt?

Not very long if it powers the water pump, -possibly 5-7 minutes before you overheat.

Read more

What happens when you put directional tires on backwards?

Directional tires can be moved from side-to-side for testing purposes.The short time that they are on the vehicle backwards will not harm the tire.Results 1.If the vehicle pulls in the opposite direction, the defective tire is 1 of the front tires.

Read more

Can a bad serpentine belt make car not start?

No only if it's a broken cam belt

Read more

Can you pedal backwards on a Freecoaster?

With the standard coaster brake hub, if you roll backwards and do not exert any force forwards or backwards on the pedals, the pedals will not move and you will roll freely backwards.

Read more

How can you tell if you have a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

What happens when the serpentine belt breaks on a car?

when serpentine belt breaks alternator and water pump stop working along with power steering pump

Read more

Is a serpentine belt the same as a timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

Can you get a diagram of a serpentine belt for a 2000 Ford Escort ZX2 please?

lift the hood. usually there.

Read more

Where can you obtain a serpentine belt diagram for a 1993 VW?

Go to your closest Autozone and they can print you one out.

Read more

How do you change a serpentine belt on a Chevy Silverado?

Shop Products Familiarize yourself with the belt routing diagram.Insert a 3/8 inch drive ratchet into the belt tensioner.Pull the tensioner counterclockwise to loosen the belt.Pull the belt off the idler pulley.Release the tensioner.Pull the belt off and out.

Read more

How do you replace a serpentine belt on a 1995 Chevrolet Camero?

Replacing the serpentine belt on both V6 & V8 rear drive engine are fairly easy than front wheel drive. The belt is located just between the front of the engine and the radiator. You have plenty of clearance to work. Just need to losen the tension and the belt should come out. Putting the new...

Read more

How do you change a serpentine belt on a 2001 Chevy Suburban?

Read more

Where can you find a diagram for installing a serpentine belt?

This should be on a sticker under the hood of the car, or in the owners manual, or available from your local auto parts store at no charge.

Read more

How do you change a serpentine belt on a 2001 Chrysler Town and Country?

How to Replace the Serpentine Belt in a Chrysler Town & Country Open the hood and find the belt tensioner pulley. Look at how the belt is routed around various pulleys. Use a wrench to rotate the belt tensioner pulley bolt and slide the old belt off of the tensioner pulley. Make sure y...

Read more

How do you change a serpentine belt on a 2008 Toyota Corolla?

Read more

How do you install a serpentine belt on a 99 Isuzu Rodeo?

There is a belt tensioner (spring loaded pulley that automatically keeps the belt tight) that needs to be temporarily slackened while the now loose belt is slipped off one of the accessories. Sorry, but I can't remember what tool is needed to loosen the belt tensioner. Just opening the hood and o...

Read more

How do you change a serpentine belt on a Mazda 3?

How to Replace a Mazda 3 Serpentine Belt Open the Mazda 3's hood and support it with the prop rod. Connect the belt-tensioner tool into serpentine belt tensioner and move the tensioner pulley away from the belt with the tool. Pull the belt off the engine accessory pulleys by hand. Stretch ...

Read more

What happens when a fly wheel is put on backwards?

It rotates the other way.Yeah, right.You CANNOT put a flywheel on backwards. It's not physically possible to mate the flywheel with the crankshaft unless it is the correct direction.

Read more

How do you align a serpentine belt pulley?

Read more

How do you change the serpentine belt on a 1994 mercury cougar xr7?

with a 1/2" rachet or breaker bar placed in the square whole on the tensioner pully, you push (from passenger side to drivers) which will release the presure on the belt. Might want to draw a "map" of how the belt goes cause it ain't obvious when its off the car.

Read more

Do you losen the altinator to change serpentine belt on a 94 Jimmy?

You'll have to loosen the alternator to get the belt off, unless you have a tensioner pulley in the sequence of the serpentine. yes it removes the tension to make it easier just did it last weekend.

Read more

How do you repair the serpentine belt on a 1998 Mitsubishi Galant?

You don't repair a serpentine belt. You replace the worn or broken belt with a new one.

Read more

What does a serpentine belt do?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

How many miles can you get out of a serpentine belt?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

How do you release serpentine belt on a 89 Mercury Cougar?

You have to release your tensioners in order to release your serpentine belt. When you put the belt back on you have to follow the diagram on the hood of your car.

Read more

How do you replace the serpentine belt on a 1993 Mercury Cougar?

To remove the serpenteen belt on this vehicle, you must first locate the spring loaded tensioner. You will need a 1/2" breaker bar or a socket to recoil the spring load. doing this will release the tension on the belt. You can then remove the belt.NOTE: If you are just changing the belt with a ne...

Read more

Does driving backwards put miles on a car?

yes. you are still moving in a direction, and the wheels are still spinning, and the engine is still running, and the transmission is still being used.

Read more

How do you adjust serpentine belt on a 1999 Holden jackaroo?

On all U.S. vehicles that use A single serpentene the belt has an automatic tensioner. I suspect that your can does too. It could be stuck.

Read more

How do you tighten the serpentine belt on a 1997 Saturn?

You don't. The belt tension is automatically adjusted via a spring loaded tensioner. If the serpentine belt is noisy or worn out prematurely. replace the tensioner. The belt should be inspected for cracks and other signs of wear. Replace worn out belt(s) before they break leaving you stranded.

Read more

How do you get the accessory drive belt or serpentine belt off of a 1989 sunbird?

To remove the accessory drive belt or the serpentine belt from the motor on a 1989 Sunbird, it is necessary to loosen the belt tensioner. Look for a pulley that has a bolt in a slot. Loosen the bolt and move the tensioner so there is a gap in the belt. Then remove the belt from each pulley.

Read more

Where could you find an illustration on replacing serpentine belt on '97 Buick Park Avenue?

There should be an illustration in your ownners manual.Just had mine done.. mechanic had to remove psgr side motor mount to release belt. Not a fun job.trust me this ne job you want to pay someone to do, you need to lower the engine cradle to remover the PS motor mount,you could also visithttp://...

Read more

What happens if you put a clutch in backwards?

Normally if the clutch is installed backwards it would be very hard to get into gear cause the throw out bearing will not have enough room to engage and disengage the clutch.It goes into gear easily when the car is not running.

Read more

How important is a serpentine belt?

Well, it won't keep your pants up, but it does transport power to your vital automotive components.The serpentine belt is one long, snaking, winding belt that keeps your alternator, power steering pump, air conditioning and — in some cases — your water pump running smoothly and effectively.

Read more

How do you take find out how to put on a serpentine belt for a 3.3L V6 if you dont have the diagram on the van anymore or the original belt?

you don't say wot make an model... so i presume its the Chrysler new yorker as i cant think of another with a 3.3 v6.. easy answer.. buy a haynes manual.. if your gonna replace the belt.. you might as well do other stuff like replace the water pump and front engine seal while your at it..

Read more

Routing new serpentine belt on 94 Plymouth Voyager?

When routing a new serpentine belt, make note of how the old belt was routed. Take a picture of the belt routing if possible. Also most cars have a sticker under the hood with the routing on it.

Read more

Why cant you detension the serpentine belt tentioner the bolt keeps rotating and not letting you get the belt on?

because the bolt is striped or you pulley is no bad take it off and get another one

Read more

Does wd40 damage serpentine belt?

WD-40 doesn't stop rubber squeaks Spraying an oil based lube onto a serpentine or poly-ribbed drive belt may make the squeak disappear for a while, but it doesn't fix the underlying problem.Plus, it damages the belt.Bottom line to nutjobs: WD-40 should NEVER by used on rubber.

Read more

Do you put car in neutral if towing backwards on a tow dolly?

yes you could do that or to be really safe you can disconnect the drive shaft

Read more

You put your battery cable on back wards on the battery?

as long as it wasnt left on backwards very long the battery may be ok connect it the right way,make sure it is charged check the fuses and try again

Read more

How do you stop serpentine belt from squeeking?

Replace belt and check all pulleys for wear or rough spot

Read more

Is the serpentine belt the same as the timing belt?

A serpentine belt does more work than a timing belt.Timing belts synchronize the movement of the crankshaft and the camshaft while the serpentine belt transmits mechanical power which drives the air conditioner, water pump, alternator, etc.To replace a serpentine belt is easy because it is outsid...

Read more

How do you reroute serpentine belt to bypass ac compressor on 1995 town car?

If that model was available without a/c, you will need to purchase the belt for a 95 town car w/out ac, and follow the appropriate belt routing diagram for that model.

Read more

How do you put belt on pulley on Kenmore dryer?

Hard to GUESS -as you haven't given Model # or year ! -You wouldn't believe how many different dryers, Kenmore makes, so this info is ESSENTIAL. -Just as a wild guess, I'd say, fit it around the pulley FIRST, then the drum.

Read more

Your serpantine belt screeches after you put a new belt tentioner and belt dressing on you cant figure out why?

Never use belt dressing on a serpentine belt. Clean the dressing off and recheck the pulleys.

Read more

How do you install serpentine belt on 88 Chevy silverado 4x4 350 auto?

Loosen tensioner and follow label (under hood) for routing

Read more

Can you help changing V-belt to serpentine using an electric water pump?

The big issue isn't an electric water pump, but the fact that you have to replace the pulleys. If you can pull that off you should be good to go, even with a belt-driven water pump.

Read more

Why does your serpentine belt squeak when you turn your 1998 Dodge avenger on?

The Serpentine Belt needs to be tightend with the tensioner pulley (Idler Pulley)

Read more

What is a serpentine belt in a car?

A rubber belt that goes around all pulleys & has idlers as tensioners. On cars there are either v belts (belts shaped like a "v" that are tightened by moving accessories) or serpentine, which is usually one ribbed belt with idlers.

Read more

What is the correct routing for a serpentine belt on a 1999 BMW 740 il car?

It is important to have the belts of a car put in the right direction. This serpentine belt goes around the AC compressor, above the AC tensioner,under the crank pulley, around the power steering, over the alternator pulley, under the idle pulley, around the w/p,and behind the tensioner.ÊÊ

Read more

What is the serpentine drive belt?

The serpentine drive belt is the rubber belt that is connected to all the pullys 5-6 like the water pump, altenator, a/c clutch, fan, and crankshaft. usually located behind the radiator or on the side of the motor depending on what the motor is and what its in.

Read more

Does Jiffy Lube change serpentine belts?

The serpentine belt! For this key component, rely on the Jiffy Lube® serpentine belt replacement to help keep your vehicle on the road.

Read more

What happens when the serpentine belt breaks?

That means when your belt breaks, slips and, ultimately, wears out, everything—from the power steering pump to the alternator and air conditioner—stops working.What's more, the parts it controls can become severely damaged.Broken hoses and belts are bad; a damaged engine is even worse.

Read more

Does serpentine belt affect air conditioner?

Yes, a worn serpentine belt can slip slightly and generate heat due to which AC stops working.The heat generated by the slipping belt over-heats the air conditioner clutch and can cause it to release.

Read more

What happens when the catalyic converter is put on backwards?

the exhaust wont flow as good. i recommend for the best flow is to just take a broom stick and punch a hole in it and make sure it is on the right direction.+++ If that nonsense is what you think the right answer I am glad there's no chance of you ever working on my car. For a start I doubt it's ...

Read more

How do you get the tensioner to move on 1988 caravan to replace serpentine belt having a diffucut time trying to get belt on?

You don't mention which engine but on my 90 3.3 I put a wrench on it and just move it. It's kinda hard.

Read more

What would cause a serpentine belt to squeal?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).Squealing sound: Belt slipping.

Read more

What does a bad serpentine belt look like?

The symptoms of a loose serpentine belt include a loud squealing noise when the engine is started or when the steering is turned all the way to one side.A serpentine belt that keeps slipping off the pulley is another symptom of a bad tensioner.

Read more

What causes a serpentine belt to slip off?

Slipping can be the result of a loss of belt tension (or a weak automatic tensioner) or pulley misalignment.When the belt slips off the track, the friction between the belt and accessory drive pulleys causes the belt to overheat.If you hear a high pitched squealing noise, it's probably time for a...

Read more

What are signs of a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

How much does it cost to replace a serpentine belt?

Typical costs: Hiring a mechanic to replace a serpentine belt typically costs about $60-$200 or more.This includes $25-$75 for the belt plus half an hour to an hour of labor, at $75-$120 per hour.The job could even take longer on some vehicles, if the belt is difficult to access or install quickly.

Read more

What causes a serpentine belt to come off?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).

Read more

Need diagram for 2004 freightliner serpentine belt?

Need an engine make and model to answer this. You either have a Detroit Diesel, Mercedes Benz, Cummins, or Caterpillar engine.

Read more

How often should serpentine belt be changed?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more

Does 2002 Camry XL have serpentine belt?

The 2.4 engine has a timing chain. The 3.0 engine has a timing belt, assuming the timing belt is what your asking about.

Read more

Does the serpentine belt affect the transmission?

Effect of Serpentine Belts on Transmission.As a result, if the serpentine belt is worn out or breaks, it results in engine overheating and losing the powered steering and charging system.

Read more

What happens if you put an air filter in backwards?

By installing your filter backwards, air will have a harder time flowing through the filter and your air handler will have to work harder to make up for the loss of airflow.That arrow must always face toward the furnace and away from the return duct that carries the air in need of heating or cool...

Read more

Does serpentine belts slow your car down?

Probably, a little. However, they are required for every other function your car uses, including the generator. So you kinda need it.

Read more

Diagram for changing the serpentine belt?

As you listed no make, model, engine, or year, all I can say is look under the hood for a placard diagram. Usually there is one there.

Read more

How long do BMW serpentine belts last?

With that being said most serpentine/drive belts can last for a very long time before they need to be replaced.The lifespan of the belt will depend mostly on the type of material it's made of.Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 mi...

Read more

What causes the serpentine belt to break?

Serpentine belt problems usually result from one of three causes: a defective belt tensioner; misalignment of a pulley; or, defective bearings in the tensioner, idler, or one of accessories driven by the belt (including the water pump).Squealing sound: Belt slipping.

Read more

Does Jiffy Lube replace serpentine belts?

The serpentine belt! For this key component, rely on the Jiffy Lube® serpentine belt replacement to help keep your vehicle on the road.

Read more

What is the purpose of a serpentine belt?

A serpentine belt is a single, continuous belt used to drive multiple peripheral devices in an automotive engine, such as an alternator, power steering pump, water pump, air conditioning compressor, air pump, etc.

Read more

What happens if a serpentine belt breaks while driving?

A broken serpentine belt leads to a sudden loss of power assist for the steering system, where the steering wheel all-of-a-sudden becomes very hard to turn.A broken serpentine belt stops the water pump from circulating coolant (antifreeze) through the cooling system, and the engine can overheat -...

Read more

What are the signs of a bad serpentine belt?

Symptoms of a Bad or Failing Serpentine/Drive Belt Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. Power steering and AC not working. If the serpentine belt completely fails and breaks...

Read more

How do you do you find the serpentine belt diagram for a Toyota RAV4 2001?

There should be a diagram under the hood somewhere. Normally on the fan shroud. Click the link for a diagram. If you do not see one search with the term "2001 Toyota Rav 4 belt diagram" and you will find a diagram.

Read more

Where is the serpentine belt adjustment bolt on a 1997 Chrysler Town and Country?

The serpentine belt tensioner is spring loaded. There is no adjustment.

Read more

Will a serpentine belt failure damage the engine on the 2001 Rodeo V6?

Not usually but it can be an indication of a problem with one of the driven accessories.A timing belt in many circumstances can indeed do damage if it breaks so replace it at the proper intervals.

Read more

How often does a serpentine belt need to be replaced?

How often does a serpentine belt need to be replaced? Serpentine belts are built to last—much longer than before because of advancements in rubber technology.Under ideal conditions, a belt should stick with you for an average of 60,000 to 100,000 miles.

Read more