Pulleys

Types of pulleys?

Lever, wedge, inclined plane, wheel n axle, screw, and pulley.

Read more

Why do cars use belts and pulleys?

It transfers power from the alternator to the crankshaft and the camshaft to make your engine work.

Read more

Can a bad harmonic balancer make an intermittent squealing noise you have replaced all tensioner and idler pulleys but it still makes this noise with the belt removed?

not always usally makes an noise close to a rattle or knocking hence harmonic.use a broom stick or hose to use as a listening device to locate the exact place of your noise could be starter sticking in(ect...)

Read more

What are the types of pulley?

There are fixed, moveable, and compound pulleys.

Read more

Which way does the pulley bolt turn?

Most bolts turn counterclockwise to come off. Year, make, model and which pulley would be helpful.

Read more

What is the pulley in a mouse trap car?

The pulley on a mouse trap car acts as an extender (rods balloons etc.) , allowing the force of the pull to be stronger than one without a pulley based on it's positioning. There are 4 ways to use a pulley with a mouse trap car: 1) Leverage 2) Temperance 3) Steering 4) Balance There are also di...

Read more

WHY IS MY CAR IS NOT TURNING ON COULD IT BE THE PULLEY?

Can be a dead battery, defective starter, loose or corroded battery connection, or blown main fuse. If nothing comes on when you turn on the ignition switch and your interior lights are not working it is not the starter.Have your battery checked .

Read more

Without the engine a car can't run right?

Unless it is all electric - then it has a motor.

Read more

Types of moveable pulleys?

Moveable pulleys are cranes, conveyor belts, and cable cars.

Read more

WHAT PULLEY DO I loosen to get single drive belt on?

If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt. If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the be...

Read more

How do you remove and replace the power steering pulley on a 1997 Ford Aerostar van 3.0 engine?

You will need a special tool to pull the pulley off the shaft. Some parts stores will lend you the tool, free of charge. Thank you. I had to rent the 'pulley puller', and remove the pulley prior to removing the power steering pump. Then replace the pump on the car and use the pulley tool to press...

Read more

How does a pulley car work?

a pulley car works by attaching a motor and a battery to a wooden base with an axle and wheels.the motor is controlled by the batterys power and is useally controling the wheels by using rope,a rubber band or possibly a hair band.

Read more

How do pulleys works in a motor car?

They allow for a mechanical link from the engines crankshaft, to other components of the vehicle. (Via the drive belt)They also allow for variable ratio's, to allow for items attached to the belt to turn at different speeds then that of your crankshaft.Example:Your crankshaft turns at 1000RPM,You...

Read more

Is an idler pulley the same as a tension pulley?

pretty much-the 2 get confused all the time. Technically a tensioner is an assembly with a spring and an idler is a fixed pulley-most newer cars have both.

Read more

How do you remove PS pulley on 93 Camaro?

first of all you crazy if you dont know how to do thatYou will need a power steering pulley puller, no joke.

Read more

What causes a pulley to make noise on a 1992 Nissan maxima?

it is time to change bearing on that pulley

Read more

How do you build a pulley motor car for a science project?

Introduction:Pulley motor car is an electric car using pulleys to transfer the mechanical energy from the motor to the wheels. MiniScience's Pulley Car activity introduces students to compound machines and simple machines including pulley, wheel and axle while incorporating problem solving, mecha...

Read more

What are the two types of pulleys?

there are two types of pulleys1. movable pulley2. fixed pulley

Read more

Where are pulleys liked?

What does this even mean?

Read more

Reverse threading on crank pulley?

What is your question? You have not asked a question or provided enough information for an answer to be given.

Read more

On a 1994 ford aerostar how do you reach the timing mark with a timing gun with the pulleys in the way?

get at it from the bottom get a white marker and mark the timing spot then go up top and you should be able to see it

Read more

How many pulleys are on a 1991 Chrysler lebaron?

There are 7 acording to Haynes

Read more

How do you set serpentine belt tension on a Chrysler?

The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.

Read more

Can you change a crankshaft pulley wheel your self or is it a job for a garage?

hi your best let a garage do the job they can be very tight to remove and in most cases you ned a special tool to do so.

Read more

How do you remove the crank bolt on a 1994 Honda civic?

Use a harmonic balancer holding tool DenLors 648796 to keep the pulley stationary while loosening the bolt.

Read more

How do you take off crankshaft pulley on 2 liter diesel year 2001 without the engine turning?

Use a strap wrench or chain wrench on the pulley to hold it secure.

Read more

What is a pulley made of?

depends on what the pulley is on...some pulleys on air compressors are cast aluminum... others are made of steel both machined and pressed2. Pulleys on older sail ships were commonly made of wood for cheapness and corrosion resistance. Today, any suitably rigid material may be used, depending on ...

Read more

How do you break loose the crankshaft pulley bolt on a 1997 Honda Accord?

Impact wrench. It's the ONLY thing that works.

Read more

Do idler pulleys rotate?

ldle in english means to sit at rest or be still so i can see where this term may confuse you. but an idler pulley on a car rides on a bearing that spins. so YESit turns. it is used as an adjustment that your fan or SERPENTINE belt rides on .to keep tension on your belt.to clarify, the pulley by ...

Read more

What pulley drives alternator belt What is wrong if this pulley isn't turning?

the pulley on the harmonic balance drives the alternator belt. this is the pulley at the bottom of the engine ,on the front of the crank shaft if this pulley is not turning you have a problem. this means either the key is missing or the crankshaft is broken

Read more

Can you change snowblower pulley size?

It depends on the snowblower, belt type and what you arer trying to achieve by making the change. The replacement pulley(s) will have to be the same shaft id as the original to start. Next make sure that there is room inside the snowblower for the new pulley. Thirdly the belt may have to change d...

Read more

What is the function of the idler pulley on cars?

Idler pulleys are used to maximize belt contact with other pulleys and to redirect belt around other parts that might interfere with the belt.

Read more

Does a camshaft pulley interchange with a 1990 Honda accord to a 1992 Honda accord?

Yes it does interchange. 1990-1993 Accords have the same camshaft pulley (or cog).

Read more

What is moveable pulley?

it is a pulley that is very moveable

Read more

How do you fix or change tensioner pulley?

The tensioner pulley has a sealed bearing and cannot be serviced, it must be replaced when it goes bad. You should inspect the tensioner assembly carefully before replacing just the pulley, the mounting bolt tends to literally wear right through the arm on a lot of the factory tensioners, causing...

Read more

Where is the car pulley located?

It has the car belt wrapped around it, on the end of the car shaft.

Read more

How do you losen the tensioning pulley Ford Focus?

You don't loosen it, you pry it back to remove tension.

Read more

You have removed the crankshaft pulley nut but pulley will not come off?

You may need a pulley (aka gear) puller to pull it off of the crank. The puller comes usually with bolts or claws you can ancor onto the pulley...

Read more

How do you replace a crankshaft pulley?

remove center bolt and use the required puller

Read more

Can the bearings on the end of the supercharger that connect to the pulley be replaced by part or does the complete unit need to be replaced?

What manufacturer of super charger, Roots or Centrifical

Read more

What causes a pulley to wobble?

Things that might cause a pulley to wobble:The pulley is bent.The shaft the pulley is on is bent.The pulley is mounted crooked.

Read more

Serpentine belt rides off tensioner pulley. this pully looks out of line where do i adjust it?

It more than likely needs new bearings. That is why it is out of line, unless the vehicle has been in an accident. Remove the belt, and remove the tensioner idler pulley and repair it.

Read more

What is the pulley system for a mousetrap car?

Slows down the power output of the spring on the trap. So that makes it go slower, and go much further.

Read more