You can use a multi meter and connect it to the battery and set it for like 20 volts dc. Crank it up and see what it's reading. It should read about 13 volts or more. You can turn on the lights and see if it still reads the same. It should. If it's lower than 13 I would assume that it's not charg...
ebc company Dennis kirk parts 4 metric pg 660 133.99 free shipping (toolmanx3 @netzero.com )just order
they use the rugular your mums motor i actually want to know e.g 5w 40
the oil mix is 32 to 1 or 50 to 1 for synthetic oil the oil mix is 32 to 1 or 50 to 1 for synthetic oil
there are two bolts in the back of the seat. remove them and then slide the seat back about an inch and remove
no its inergrated into the pcm. you have to change the program with a programer or a chip
I'm pretty positive there is a clear window on the side of the motor case,window should be about half full when the machine is turned off
PW 80 is a 2 stroke. It does not have oil in the crank case. I think you mean transmission oil. I use 10w40 engine oil in mine and it works great.
The VIN should be etched on the tube frame of the ATV. It's on the left side, right behind the left front tire. It's should be 16 characters long. * The VIN begins with the prefix "JKA", "JKB", "JK1", "JSA", or "LM4" * On all motorcycles it is stamped on the side of the steering head. On street-l...
pressure test your coolant system, if it wont hold pressure you most likely have cracked some part of the engine internally, hence leaking coolant into the oil
Acceleration1/4 mile12.91 sec @ 109.09mph (176km)0-30mph1.8 secs0-40mph2.5 secs0-50mph3.5 secs0-60mph4.6 secs0-70mph6.0 secs0-80mph7.8 secs0-90mph9.8 secs0-100mph12.7 secsSpeedo error30mph30 mph (mph = miles per hour)60mph55.96 mphBraking30mph32 ft (9.8m)60mph135ft (41.1m)Speed in gears measured ...
the numbers on the oil determine the viscosity of it (thickness) so it means that after the engine warms up the oil will either be thinner or thicker for a certain amount of time, but to answer the question for the bike the best bet would be Castrol SAE 10W-40. that's what i use for my bike.(07 n...
Go to WalMart and look it up in their application guide.
The oil capacity of a 1996 Kawasaki Vulcan 800 is 2.9L with a filter change, 2.8L without, and 3.1L for a dry engine.
The 10th digit represents the year. Here is a great article to help you decode the full atv vin number. http://www.atvstyle.com/index.php/atv-vin-number
well it depends how fast your going!!if your going 40mph it will take an hourif you want to know how fast at other speedsjust take how fast your going and if it is double 40 (80), then you must half the time and vice versathough for your convenience10mph-4 hours20mph-2 hours30mph-1 and a half hou...
About 3 3/4 - 4 quarts. Don't forget to pull BOTH drain plugs on the bottom of the engine or you will leave about 1 qt of dirty oil in the engine.
remove the air scoops, the rear side panels, the seat and the gas tank------- tools needed will be 10 and 8 mm sockets, #3 Phillips screw driver and a 18 mm socket for the plug.
What is the average and cost for a kawasaki ninja 250r
put the piston at top dear center and have the timing mark point to the 12 o clock position realitive to the engine. and assemble the chain
* The VIN begins with the prefix "JKA", "JKB", "JK1", "JSA", or "LM4" * On all motorcycles it is stamped on the side of the steering head. On street-legal motorcycles, the VIN also appears on the Safety Certification Label affixed to, or near, the side of the steering head. * On ATV's it is stamp...
When you open the toolbox on back of the seat, there are two bolts inside. Remove the and the seat lifts right off.
3.2L W/ FILTER, 3.5L AT FILTER CHANGE, 4L COMPLETELYDRY